How to use this file...(Parts Manuals) ————————————————————————————————————————————––– Instructions for Print Vendors (Paper Manuals) Paper Size: * 11 x 17 * Body—50 lbs brilliant white offset or equivalent. * Cover—on pre-printed grid stock whenever available.
Parts Manual LARGE FRAME SNOWTHROWERS (MODELS 860, 970 & 1180) MODEL 860 SNOWTHROWERS MODEL 970 SNOWTHROWERS Mfg. No. Description Mfg. No.
Table of Contents SNOWTHROWER COMPONENTS PAGES Handles and Controls Group ....................................2 Engine & Frame Group - 8HP, Manual Start .........14 Engine & Frame Group - 8HP, Manual Start .........16 Engine & Frame Group - 8HP, Manual Start .........20 Engine & Frame Group - 8HP, Electric Start .........22 Engine & Frame Group - 8HP, Electric Start .........24 Engine & Frame Group - 9HP, Manual Start .........28 Engine & Frame Group - 9HP, Electric Start .........
Handles and Controls Group 985771 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 7 6 Apply adheasive to secure grips. 10 9 8 5 43 11 Ref. 12 required on slotted holes only. 12 32 33 31 25 4 29 34 14 28 13 40 35 17 37 3 15 25 33 3 16 38 30 11 37 29 2 7 36 39 27 28 18 27 28 29 1 19 20 Shift rod assembly (Ref. 38) must pivot freely on pivot blocks, (Ref. 33). 4 41 26 25 21 43 34 22 44 23 3 50 Mount bushings (Ref.
Handles and Controls Group REF NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 PART NO. QTY.
Handles and Controls Group 985771 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 7 6 Apply adheasive to secure grips. 10 9 8 5 43 11 Ref. 12 required on slotted holes only. 12 32 33 31 25 4 29 34 14 28 13 40 35 17 37 3 15 25 33 3 16 38 30 11 37 29 2 7 36 39 27 28 18 27 28 29 1 19 20 Shift rod assembly (Ref. 38) must pivot freely on pivot blocks, (Ref. 33). 4 41 26 25 21 43 34 22 44 23 3 50 Mount bushings (Ref.
Handles and Controls Group REF NO. 50 51 52 53 54 55 PART NO. QTY. 916168 1960294 1960518 1668526 1707452 1917372 2 2 2 1 1 1 DESCRIPTION PIN, Spring NUT, Hex Flange, 1/4-20 PUSH NUT, Bolt Retainer 1/4 CLUTCH ROD, Lower, LH SPRING, Clutch Rod NUT, Hex, 5/16-18 Footnotes: The above parts group applies to the following Mfg. Nos.
Handles and Controls Group 985916 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Must slide freely in dash assembly (Ref 8). Apply lubricant as required. 7 6 14 5 Apply adhesive to secure grips. 15 11 10 8 16 12 9 13 62 Insert shift rod (Ref. 55) into outter hole of Ref. 61. 58 61 51 4 Ref. 13 required on slotted holes only.
Handles and Controls Group REF NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 PART NO. QTY.
Handles and Controls Group 985916 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Must slide freely in dash assembly (Ref 8). Apply lubricant as required. 7 6 14 5 Apply adhesive to secure grips. 15 11 10 8 16 12 9 13 62 Insert shift rod (Ref. 55) into outter hole of Ref. 61. 58 61 51 4 Ref. 13 required on slotted holes only.
Handles and Controls Group REF NO. 50 51 52 53 54 55 56 57 58 59 60 61 62 63 PART NO. QTY.
Handles and Controls Group 985643 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 1 5 Apply adheasive to secure grips. 4 6 49 72 9 70 3 11 2 16 6 73 15 8 71 17 18 10 59 20 19 7 6 60 38 34 21 35 23 22 13 25 36 75 6 24 69 57 26 56 62 59 54 6 76 8 58 68 14 61 74 28 55 63 64 67 65 56 29 Shift rod assembly (Ref. 54) must pivot freely on pivot blocks (Ref. 59).
Handles and Controls Group REF NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 PART NO. QTY.
Handles and Controls Group 985643 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 1 5 Apply adheasive to secure grips. 4 6 49 72 9 70 3 11 2 16 6 73 15 8 71 17 18 10 59 20 19 7 6 60 38 34 21 35 23 22 13 25 36 75 6 24 69 57 26 56 62 59 54 6 76 8 58 68 14 61 74 28 55 63 64 67 65 56 29 Shift rod assembly (Ref. 54) must pivot freely on pivot blocks (Ref. 59).
Handles and Controls Group REF NO. 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 PART NO. QTY.
Engine & Frame Group - 8HP, Manual Start 985633 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Position idler pulley (Ref. 25) at center of slot in clutch arm (Ref. 22). 3 1 Use 0-2 washers between Ref. 40 & 22 to assure a centered belt and no interference between pulleys Ref. 19 & 25. 5 25 39 26 39 6 4 40 39 Hook one end of spring (Ref. 27) over clutch rod assembly (Ref. 22) between tabs and other end into slot in frame.
Engine & Frame Group - 8HP, Manual Start REF NO. PART NO. QTY.
Engine & Frame Group - 8HP, Manual Start 985634 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 3 Position idler pulley (Ref. 34) at center of slot in clutch arm (Ref. 31). 1 Use 0-2 washers between Ref. 58 & 31 to assure a centered belt and no interference between pulleys Ref. 27 & 34. 4 6 35 57 34 5 Hook one end of spring (Ref. 36) over clutch rod assembly (Ref. 31) between tabs and other end into slot in frame.
Engine & Frame Group - 8HP, Manual Start REF NO. PART NO. QTY.
Engine & Frame Group - 8HP, Manual Start 985634 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 3 Position idler pulley (Ref. 34) at center of slot in clutch arm (Ref. 31). 1 Use 0-2 washers between Ref. 58 & 31 to assure a centered belt and no interference between pulleys Ref. 27 & 34. 4 6 35 57 34 5 Hook one end of spring (Ref. 36) over clutch rod assembly (Ref. 31) between tabs and other end into slot in frame.
Engine & Frame Group - 8HP, Manual Start REF NO. 49 50 51 52 53 54 55 56 57 58 PART NO. QTY. 1702979 ** 1702017 1701776 1922755 1916965 1960345 1701011 1924940 157081 1 1 1 1 1 1 1 1 3 1 DESCRIPTION SPRING, Compression WICK, Oil PULLEY, Drive PULLEY, Drive WASHER,13/32 x 1 LOCKWASHER, Spring, 3/8 CAPSCREW, Hex Head, 3/8-24 x 2 TIE, Self Locking WASHER, Flat,13/32 SPACER Footnotes: * See your local Tecumseh distributor for Parts and Service. ** Not a Service Part.
Engine & Frame Group - 8HP, Manual Start 985773 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Position idler pulley (Ref. 25) at center of slot in clutch arm (Ref. 22). 3 1 Use 0-2 washers between Ref. 40 & 22 to assure a centered belt and no interference between pulleys Ref. 19 & 25. 5 25 39 26 39 6 4 40 39 Hook one end of spring (Ref. 27) over clutch rod assembly (Ref. 22) between tabs and other end into slot in frame.
Engine & Frame Group - 8HP, Manual Start REF NO. PART NO. QTY.
Engine & Frame Group - 8HP, Electric Start 986111 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Position idler pulley (Ref. 25) at center of slot in clutch arm (Ref. 22). 3 1 Use 0-2 washers between Ref. 40 & 22 to assure a centered belt and no interference between pulleys Ref. 19 & 25. 5 25 39 26 39 6 4 40 39 Hook one end of spring (Ref. 27) over clutch rod assembly (Ref. 22) between tabs and other end into slot in frame.
Engine & Frame Group - 8HP, Electric Start REF NO. PART NO. QTY.
Engine & Frame Group - 8HP, Electric Start 986095 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 3 Position idler pulley (Ref. 34) at center of slot in clutch arm (Ref. 31). 1 Use 0-2 washers between Ref. 58 & 31 to assure a centered belt and no interference between pulleys Ref. 27 & 34. 59 4 6 35 57 34 5 Hook one end of spring (Ref. 36) over clutch rod assembly (Ref. 31) between tabs and other end into slot in frame.
Engine & Frame Group - 8HP, Electric Start REF NO. PART NO. QTY.
Engine & Frame Group - 8HP, Electric Start 986095 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 3 Position idler pulley (Ref. 34) at center of slot in clutch arm (Ref. 31). 1 Use 0-2 washers between Ref. 58 & 31 to assure a centered belt and no interference between pulleys Ref. 27 & 34. 59 4 6 35 57 34 5 Hook one end of spring (Ref. 36) over clutch rod assembly (Ref. 31) between tabs and other end into slot in frame.
Engine & Frame Group - 8HP, Electric Start REF NO. 49 50 51 52 53 54 55 56 57 58 59 PART NO. QTY. 1702979 ** 1702017 1701776 1922755 1916965 1960345 1701011 1924940 157081 1717432 1 1 1 1 1 1 1 1 3 1 1 DESCRIPTION SPRING, Compression WICK, Oil PULLEY, Drive PULLEY, Drive WASHER,13/32 x 1 LOCKWASHER, Spring, 3/8 CAPSCREW, Hex Head, 3/8-24 x 2 TIE, Self Locking WASHER, Flat,13/32 SPACER CORD, Electric, 3 Prong Footnotes: * See your local Tecumseh distributor for Parts and Service.
Engine & Frame Group - 9HP, Manual Start 985635 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 3 Position idler pulley (Ref. 34) at center of slot in clutch arm (Ref. 31). 1 Use 0-2 washers between Ref. 58 & 31 to assure a centered belt and no interference between pulleys Ref. 27 & 34. 4 6 35 57 34 5 Hook one end of spring (Ref. 36) over clutch rod assembly (Ref. 31) between tabs and other end into slot in frame.
Engine & Frame Group - 9HP, Manual Start REF NO. PART NO. QTY.
Engine & Frame Group - 9HP, Manual Start 985635 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 3 Position idler pulley (Ref. 34) at center of slot in clutch arm (Ref. 31). 1 Use 0-2 washers between Ref. 58 & 31 to assure a centered belt and no interference between pulleys Ref. 27 & 34. 4 6 35 57 34 5 Hook one end of spring (Ref. 36) over clutch rod assembly (Ref. 31) between tabs and other end into slot in frame.
Engine & Frame Group - 9HP, Manual Start REF NO. 49 50 51 52 53 54 55 56 57 58 PART NO. QTY. 1702979 ** 1702017 1701776 1922755 1916965 1960345 1701011 1924940 157081 1 1 1 1 1 1 1 1 3 1 DESCRIPTION SPRING, Compression WICK, Oil PULLEY, Drive PULLEY, Drive WASHER,13/32 x 1 LOCKWASHER, Spring, 3/8 CAPSCREW, Hex Head, 3/8-24 x 2 TIE, Self Locking WASHER, Flat,13/32 SPACER Footnotes: * See your local Tecumseh distributor for Parts and Service. ** Not a Service Part.
Engine & Frame Group - 9HP, Electric Start 986098 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 3 Position idler pulley (Ref. 34) at center of slot in clutch arm (Ref. 31). 1 Use 0-2 washers between Ref. 58 & 31 to assure a centered belt and no interference between pulleys Ref. 27 & 34. 59 4 57 34 5 6 35 Hook one end of spring (Ref. 36) over clutch rod assembly (Ref. 31) between tabs and other end into slot in frame.
Engine & Frame Group - 9HP, Electric Start REF NO. PART NO. QTY.
Engine & Frame Group - 9HP, Electric Start 986098 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 3 Position idler pulley (Ref. 34) at center of slot in clutch arm (Ref. 31). 1 Use 0-2 washers between Ref. 58 & 31 to assure a centered belt and no interference between pulleys Ref. 27 & 34. 59 4 57 34 5 6 35 Hook one end of spring (Ref. 36) over clutch rod assembly (Ref. 31) between tabs and other end into slot in frame.
Engine & Frame Group - 9HP, Electric Start REF NO. 49 50 51 52 53 54 55 56 57 58 59 PART NO. QTY. 1702979 ** 1702017 1701776 1922755 1916965 1960345 1701011 1924940 157081 1717432 1 1 1 1 1 1 1 1 3 1 1 DESCRIPTION SPRING, Compression WICK, Oil PULLEY, Drive PULLEY, Drive WASHER,13/32 x 1 LOCKWASHER, Spring, 3/8 CAPSCREW, Hex Head, 3/8-24 x 2 TIE, Self Locking WASHER, Flat,13/32 SPACER CORD, Electric, 3 Prong Footnotes: * See your local Tecumseh distributor for Parts and Service.
Engine & Frame Group - 11HP, Manual Start 985636 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 3 Position idler pulley (Ref. 34) at center of slot in clutch arm (Ref. 31). 1 Use 0-2 washers between Ref. 58 & 31 to assure a centered belt and no interference between pulleys Ref. 27 & 34. 4 6 35 57 34 5 Hook one end of spring (Ref. 36) over clutch rod assembly (Ref. 31) between tabs and other end into slot in frame.
Engine & Frame Group - 11HP, Manual Start REF NO. PART NO. QTY.
Engine & Frame Group - 11HP, Manual Start 985636 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 3 Position idler pulley (Ref. 34) at center of slot in clutch arm (Ref. 31). 1 Use 0-2 washers between Ref. 58 & 31 to assure a centered belt and no interference between pulleys Ref. 27 & 34. 4 6 35 57 34 5 Hook one end of spring (Ref. 36) over clutch rod assembly (Ref. 31) between tabs and other end into slot in frame.
Engine & Frame Group - 11HP, Manual Start REF NO. 49 50 51 52 53 54 55 56 57 58 PART NO. QTY. 1701849 ** 1702017 1701776 1922755 1916965 1960345 1701011 1924940 157081 1 1 1 1 1 1 1 1 3 1 DESCRIPTION SPRING, Compression WICK, Oil PULLEY, Drive PULLEY, Drive WASHER,13/32 x 1 LOCKWASHER, Spring, 3/8 CAPSCREW, Hex Head, 3/8-24 x 2 TIE, Self Locking WASHER, Flat,13/32 SPACER Footnotes: * See your local Tecumseh distributor for Parts and Service. ** Not a Service Part.
Engine & Frame Group - 11HP, Electric Start 986099 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 3 Position idler pulley (Ref. 34) at center of slot in clutch arm (Ref. 31). 1 Use 0-2 washers between Ref. 58 & 31 to assure a centered belt and no interference between pulleys Ref. 27 & 34. 59 4 6 35 57 34 5 Hook one end of spring (Ref. 36) over clutch rod assembly (Ref. 31) between tabs and other end into slot in frame.
Engine & Frame Group - 11HP, Electric Start REF NO. PART NO. QTY.
Engine & Frame Group - 11HP, Electric Start 986099 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 3 Position idler pulley (Ref. 34) at center of slot in clutch arm (Ref. 31). 1 Use 0-2 washers between Ref. 58 & 31 to assure a centered belt and no interference between pulleys Ref. 27 & 34. 59 4 6 35 57 34 5 Hook one end of spring (Ref. 36) over clutch rod assembly (Ref. 31) between tabs and other end into slot in frame.
Engine & Frame Group - 11HP, Electric Start REF NO. 49 50 51 52 53 54 55 56 57 58 59 PART NO. QTY. 1701849 ** 1702017 1701776 1922755 1916965 1960345 1701011 1924940 157081 1717432 1 1 1 1 1 1 1 1 3 1 1 DESCRIPTION SPRING, Compression WICK, Oil PULLEY, Drive PULLEY, Drive WASHER,13/32 x 1 LOCKWASHER, Spring, 3/8 CAPSCREW, Hex Head, 3/8-24 x 2 TIE, Self Locking WASHER, Flat,13/32 SPACER CORD, Electric, 3 Prong Footnotes: * See your local Tecumseh distributor for Parts and Service.
Auger and Impeller Group - 24” 985466 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 4 End of hub to be flush with end of rolled down shaft (Ref. 9). 1 2 Torque to 30 -34 ft-lbs. 40 - 46 Nm. 5 10 7 6 2 14 16 10 17 10 18 12 19 9 Impeller to be positioned against bearing before tightening set screw. 13 20 Marked side of worm gear must contact against left thrust washer to assure proper gear mesh. 24 - 28 Nm. 11 6 15 3 8 Torque to 18-21 ft-lbs.
Auger and Impeller Group - 24” REF NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 PART NO. QTY.
Auger and Impeller Group - 28” 985467 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 4 End of hub to be flush with end of rolled down shaft (Ref. 9). 1 2 Torque to 30 -34 ft-lbs. 40 - 46 Nm. 5 10 7 6 2 14 16 10 17 3 10 18 12 19 9 Impeller to be positioned against bearing before tightening set screw. 6 20 Marked side of worm gear must contact against left thrust washer to assure proper gear mesh. 24 - 28 Nm. 8 11 13 15 Torque to 18-21 ft-lbs.
Auger and Impeller Group - 28” REF NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 PART NO. QTY.
Auger and Impeller Group - 32” 985468 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 4 End of hub to be flush with end of rolled down shaft (Ref. 9). 1 2 Torque to 30 -34 ft-lbs. 40 - 46 Nm. 5 10 7 6 33 2 16 10 17 14 3 10 9 11 18 12 19 30 13 6 8 Torque to 18-21 ft-lbs. 24 - 28 Nm. Impeller to be positioned against bearing before tightening set screw.
Auger and Impeller Group - 32” REF NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 PART NO. QTY.
Auger Housing and Chute Group - 24” 983960 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Decal must cover gap at hinge pivot. 6 5 4 3 7 Plastic washer (Ref. 3) goes between chute and deflector. 33 2 1 1 16 8 9 12 10 Coat top and bottom of chute ring with grease. 13 14 11 15 17 31 16 32 30 Scraper blade should be on inside of housing. 17 13 21 28 29 20 19 18 27 26 22 25 24 23 The above parts group applies to the following Mfg. Nos.
Auger Housing and Chute Group - 24” REF NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 PART NO. QTY.
Auger Housing and Chute Group - 28” 985639 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 22 Decal must cover gap at hinge pivot. 21 9 7 5 10 10 1 1 20 19 6 14 9 18 16 12 4 3 13 17 8 2 1 15 Mount cable bracket (Ref. 20) on right hand side of handle using shift control bracket hardware. 1 25 32 23 Coat top and bottom of chute ring with grease. 24 27 When installing cable, make sure it does not come into contact with muffler.
Auger Housing and Chute Group - 28” REF NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 PART NO. QTY.
Auger Housing and Chute Group - 32” 985640 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 22 Decal must cover gap at hinge pivot. 21 9 7 5 10 10 1 1 20 19 6 14 9 18 15 12 4 3 13 17 8 2 Mount cable bracket (Ref. 20) on right hand side of handle using shift control bracket hardware. 1 1 16 25 32 23 Coat top and bottom of chute ring with grease. 24 27 When installing cable, make sure it does not come into contact with muffler.
Auger Housing and Chute Group - 32” REF NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 PART NO. QTY.
Traction Drive Group 985637 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Mounted inside of frame. 4 5 6 7 Mount to bracket in frame weldment. 8 9 1 2 12 Hook end to top left corner slot of frame. 14 13 16 11 Mounted outside of frame. 3 15 Pack groove with grease. Lubricate with 5W 50 Synthetic oil. Apply locktite, torque to 55 - 60 in-lbs. when all parts are tight against hub. 10 2 3 22 26 3 20 21 17 5 Mounted inside of frame.
Traction Drive Group REF NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 PART NO. QTY.
Traction Drive Group 985637 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Mounted inside of frame. 4 5 6 7 Mount to bracket in frame weldment. 8 9 1 2 12 Hook end to top left corner slot of frame. 14 13 16 11 Mounted outside of frame. 3 15 Pack groove with grease. Lubricate with 5W 50 Synthetic oil. Apply locktite, torque to 55 - 60 in-lbs. when all parts are tight against hub. 10 2 3 22 26 3 20 21 17 5 Mounted inside of frame.
Traction Drive Group REF NO. 50 51 52 PART NO. QTY. 1707002 1919326 1700473 1 2 1 DESCRIPTION SPRING WASHER, Flat, 11/32 BELLCRANK Footnotes: The above parts group applies to the following Mfg. Nos.
Traction Drive Group 985772 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Mounted inside of frame. 4 5 6 7 Mount to bracket in frame weldment. 8 9 1 2 12 Hook end to top left corner slot of frame. 14 13 16 11 Mounted outside of frame. 3 15 Pack groove with grease. Lubricate with 5W 50 Synthetic oil. Apply locktite, torque to 55 - 60 in-lbs. when all parts are tight against hub. 10 2 3 22 26 3 20 21 17 5 Mounted inside of frame.
Traction Drive Group REF NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 PART NO. QTY.
Traction Drive Group 985772 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Mounted inside of frame. 4 5 6 7 Mount to bracket in frame weldment. 8 9 1 2 12 Hook end to top left corner slot of frame. 14 13 16 11 Mounted outside of frame. 3 15 Pack groove with grease. Lubricate with 5W 50 Synthetic oil. Apply locktite, torque to 55 - 60 in-lbs. when all parts are tight against hub. 10 2 3 22 26 3 20 21 17 5 Mounted inside of frame.
Traction Drive Group REF NO. 50 51 52 53 54 PART NO. QTY. 1707002 1919326 1700473 1666106 1922127 1 2 1 1 1 DESCRIPTION SPRING WASHER, Flat, 11/32 BELLCRANK BUSHING, Pivot CAPSCREW, Hex Head, 5/16-18 x 1-3/4 Footnotes: The above parts group applies to the following Mfg. Nos.
Traction Drive Group 985638 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Mounted inside of frame. 4 Pack groove with grease. 5 1 14 7 2 3 15 Lubricate with 5W 50 Synthetic oil. 6 8 4 Hook end to top left corner slot of frame. 13 12 Mount to bracket in frame weldment. 16 9 5 2 27 11 26 28 Apply Loctite and Torque to 55 - 60 in-lbs. when all parts are against hub. Mounted 22 3 2 outside of frame. 10 3 20 Mounted outside of frame.
Traction Drive Group REF NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 PART NO. QTY.
Traction Drive Group 985638 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Mounted inside of frame. 4 Pack groove with grease. 5 1 14 7 2 3 15 Lubricate with 5W 50 Synthetic oil. 6 8 4 Hook end to top left corner slot of frame. 13 12 Mount to bracket in frame weldment. 16 9 5 2 27 11 26 28 Apply Loctite and Torque to 55 - 60 in-lbs. when all parts are against hub. Mounted 22 3 2 outside of frame. 10 3 20 Mounted outside of frame.
Traction Drive Group REF NO. 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 PART NO. QTY.
Decals Group - 860 D985670 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 3 WARNING TO AVOID SERIOUS INJURY 3 1 • Read Owner’s Manual before operating unit. • Never allow children to operate snowthrower. 2 • Always direct discharge chute so as to avoid injury to persons—or damage to property y • Stop engine and disconnect spark plug wire before removing debris or servicing unit. • Keep all shields and guards in place while running.
Decals Group - 860 REF NO. 1 1 2 3 3 3 4 5 6 6 7 8 8 9 10 11 PART NO. QTY.
Decals Group - 860DLX, 970 & 1180 D985935 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 2 2 2 3 1 3 1 4 5 4 6 7 1716532 6 5 10 8 9 9 The above parts group applies to the following Mfg. Nos.: 1693652 1693653 1694241 1693654 1693655 860DLX, 8HP Manual Start 860DLX, 8HP Manual Start (Export) 860DLXE, 8HP Electric Start 970M, 9HP Manual Start 970M, 9HP Manual Start (Export) 1694243 1693656 1693657 1694244 © Copyright 2002 Simplicity Manufacturing, Inc.
Decals Group - 860DLX, 970 & 1180 REF NO. 1 2 2 2 3 4 4 4 5 5 6 6 7 8 8 9 10 PART NO. QTY.
Wheels & Tires Group - 860 W983851 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 1 2 3 4 5 6 The above parts group applies to the following Mfg. Nos.: 1693650 1693651 1693763 1693775 1693984 860M, 8HP Manual Start 860M, 8HP Manual Start (Export) 860M, 8HP Manual Start 860M, 8HP Manual Start (Export) 860M, 8HP Manual Start 1693985 860M, 8HP Manual Start (Export) 1694242 860E, 8HP Electric Start © Copyright 2002 Simplicity Manufacturing, Inc. All Rights Reserved.
Wheels & Tires Group - 860 REF NO. 1 2 3 4 5 6 PART NO. QTY. 1714235 1612000 1714242 172353 153038 1666969 2 2 2 2 2 2 DESCRIPTION WHEEL & TIRE ASSEMBLY (Includes Ref. Nos. 2, 3 & 4) TIRE, 4.80-4.00-8 HUB, Wheel VALVE STEM & CAP TUBE, Tire KLIK-PIN Footnotes: The above parts group applies to the following Mfg. Nos.
Wheels & Tires Group - 860DLX & 970 W985644 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 1 2 6 3 4 5 8 5 7 3 9 10 The above parts group applies to the following Mfg. Nos.: 1693652 1693653 1694241 1693654 1693655 860DLX, 8HP Manual Start 860DLX, 8HP Manual Start (Export) 860DLXE, 8HP Electric Start 970M, 9HP Manual Start 970M, 9HP Manual Start (Export) 1694243 970E, 9HP Electricl Start © Copyright 2002 Simplicity Manufacturing, Inc. All Rights Reserved.
Wheels & Tires Group - 860DLX & 970 REF NO. 1 2 3 4 5 6 7 8 9 10 PART NO. QTY. 1921978 1919438 172353 1714242 1612000 1714235 1720307 1720306 153038 1666969 1 1 2 1 2 1 1 1 2 1 DESCRIPTION CAPSCREW, Hex Head, 5/16-18 x 2 NUT, Hex Lock ESNA Light, 5/16-18 VALVE STEM & CAP HUB, Wheel, RH TIRE, 4.80-4.00-8 WHEEL & TIRE ASSEMBLY, RH (Includes Ref. Nos. 3, 4 & 5) HUB, Wheel, LH WHEEL & TIRE ASSEMBLY, LH (Includes Ref. Nos.
Wheels & Tires Group - 1180 & 1390 W985879 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 1 2 6 3 4 5 8 5 7 3 9 10 The above parts group applies to the following Mfg. Nos.: 1693656 1180M, 11HP Manual Start 1693657 1180M, 11HP Manual Start (Export) 1694244 1180E, 11HP Electricl Start © Copyright 2002 Simplicity Manufacturing, Inc. All Rights Reserved.
Wheels & Tires Group - 1180 & 1390 REF NO. 1 2 3 4 5 6 7 8 9 10 PART NO. QTY. 1921978 1919438 172353 1722762 1722597 1722599 1722761 1722598 153038 1666969 1 1 2 1 2 1 1 1 2 1 DESCRIPTION CAPSCREW, Hex Head, 5/16-18 x 2 NUT, Hex Lock ESNA Light, 5/16-18 VALVE STEM & CAP HUB, Wheel, RH TIRE, 16 x 6.50-6 WHEEL & TIRE ASSEMBLY, RH (Includes Ref. Nos. 3, 4 & 5) HUB, Wheel, LH WHEEL & TIRE ASSEMBLY, LH (Includes Ref. Nos.
Headlight Group 985652 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 2 Light mounting hardware is included with light. 5 6 3 4 1 The above parts group applies to the following Mfg. Nos.: 1693654 1693655 1694243 1693656 1693657 970M, 9HP Manual Start 970M, 9HP Manual Start (Export) 970E, 9HP Electrical Start 1180M, 11HP Manual Start 1180M, 11HP Manual Start (Export) 1694244 1180E, 11HP Electrical Start © Copyright 2002 Simplicity Manufacturing, Inc.
Headlight Group REF NO. PART NO. QTY. 1 2 3 4 4 5 6 1921978 1919438 172353 1714242 1722762 1722597 1714235 1 1 2 2(1) 1 2 2(1) 6 1722599 1 7 8 8 9 1612000 1720307 1722761 1720306 2 1 1 1 9 1722598 1 10 11 153038 1666969 2 2(1) DESCRIPTION CAPSCREW, Hex Head, 5/16-18 x 2 NUT, Hex Lock ESNA Light, 5/16-18 VALVE STEM & CAP HUB, Wheel (860, 860DLX, 970 & 1180 Models) (Qty. 1 on 1180 Models) HUB, Wheel, RH, (1180 & 1390 Models) TIRE, (1180 & 1390), 16 x 6.
Hardware Identification & Torque Specifications Common Hardware Types Torque Specification Chart Hex Head Capscrew FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) Washer Hardware Grade Lockwasher Carriage Bolt No Marks SAE Grade 2 Hex Nut Size Of Hardware Standard Hardware Sizing 8-32 8-36 10-24 10-32 1/4-20 1/4-28 5/16-18 5/16-24 3/8-16 3/8-24 7/16-14 7/16-20 1/2-13 1/2-20 9/16-12 9/16-18 5/8-11 5/8-18 3/4-10 3/4-16 7/8-9 7/8-14 1-8 1-12 When a washer or nut is identified as 1/2”, this is the
MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 USA www.simplicitymfg.com © Copyright 2002 Simplicity Manufacturing, Inc. All Rights Reserved. Printed In USA.