SDS

ManualsBrandsSimpson Strong-Tie ManualsPaint9 oz. Crack-Pac Injection Kit

CRACK-PAC

Injection Epoxy

SAFETY DATA SHEET

CRACK-PAC

Page 1 of 8

North America SDS

1. Identification

Product Identification

Product Identifier: CRACK-PAC

(ETIPAC10, ETIPAC10KT)

Recommended Use: Two Component Low Viscosity Injection Epoxy

Use Restrictions: None Known.

Company Identification

Company: Simpson Strong-Tie Company Inc.

Address: 5956 W. Las Positas Blvd.

Pleasanton, CA 94588, USA

Phone: 1-800-999-5099

Website: www.strongtie.com

Emergency: 1-800-535-5053 (US/Canada)

1-352-323-3500 (International)

For most current SDS, please visit our website at www.strongtie.com/sds

2. Hazard Identification

General Information

CRACK-PAC® Injection Epoxy is a two part system. The two parts of this product have been assessed according to GHS

and are classified below. The final hardened material is considered nonhazardous.

Resin (blue side) GHS Classification

Physical Hazards: Not Classified.

Health Hazards: Skin Corrosion/Irritation Category 2

Serious Eye Damage/Irritation Category 2A

Sensitization, Skin Category 1

Environmental Hazards: Acute Aquatic Environmental Hazard Category 2

Chronic Aquatic Environmental Hazard Category 2

Signal Word: WARNING!

Hazard Statements: Causes skin irritation. Causes serious eye irritation. May cause an allergic skin reaction.

Toxic to aquatic life with long lasting effects.

Precautionary Statements:

Prevention: Wear protective gloves/protective clothing/eye protection/face protection. Contaminated

work clothing should not be allowed out of the workplace. Avoid breathing mist or vapor.

Wash thoroughly after handling. Avoid release to the environment.

Response: If on skin: Wash with plenty of water. If skin irritation or rash occurs: Get medical

advice/attention. Take off contaminated clothing and wash before re-use. If in eyes: Rinse

cautiously with water for several minutes. Remove contact lenses, if present and easy to

do. Continue rinsing. If eye irritation persists: Get medical advice/attention. Collect

Spillage.

Storage: Store locked up. Store in a well-ventilated place. Store between 45-90°F (7-32°C).

Disposal: Dispose of contents/container in accordance with local/regional/national regulations.

Hardener (clear side) GHS Classification

Physical Hazards: Not Classified.

Health Hazards: Acute Toxicity, Oral Category 4

Acute Toxicity, Dermal Category 4

Acute Toxicity, Inhalation Category 4

Summary of content (16 pages)

PAGE 1
CRACK-PAC® Injection Epoxy SAFETY DATA SHEET 1. Identification Product Identification Product Identifier: Recommended Use: Use Restrictions: Company Identification Company: Address: CRACK-PAC® (ETIPAC10, ETIPAC10KT) Two Component Low Viscosity Injection Epoxy None Known. Simpson Strong-Tie Company Inc. 5956 W. Las Positas Blvd. Pleasanton, CA 94588, USA Phone: 1-800-999-5099 Website: www.strongtie.
PAGE 2
CRACK-PAC® Injection Epoxy SAFETY DATA SHEET Environmental Hazards: Signal Word: Hazard Statements: Precautionary Statements: Prevention: Response: Storage: Disposal: Skin Corrosion/Irritation Serious Eye Damage/Irritation Sensitization, Skin STOT, Single Exposure Acute Aquatic Environmental Hazard Chronic Aquatic Environmental Hazard Category 1B Category 1 Category 1 Category 1(corrosive to the respiratory tract) Category 3 Category 3 DANGER! Harmful if swallowed. Harmful in contact with skin.
PAGE 3
CRACK-PAC® Injection Epoxy SAFETY DATA SHEET Ingestion: Inhalation: Rinse mouth immediately. Give large amounts of milk or water, if person is conscious. Only induce vomiting at the instruction of medical personnel. Consult a physician. Immediately remove from further exposure. Get immediate medical assistance. For those providing assistance, avoid exposure to yourself or others. Use adequate respiratory protection. Give supplemental oxygen, if available.
PAGE 4
CRACK-PAC® Injection Epoxy SAFETY DATA SHEET 8. Exposure Controls / Personal Protection Personal Protective Equipment General Protection: Eye Protection: Hand Protection: Skin and Body Protection: Respirator Protection: General Hygiene: Wear appropriate personal protective equipment. Wear chemical splash goggles or safety glasses with side shield. Wear chemical-resistant gloves such as: Nitrile, neoprene, butyl. Wear long sleeve shirt/long pants and other clothing as required to minimize contact.
PAGE 5
CRACK-PAC® Injection Epoxy SAFETY DATA SHEET Hazardous Reactions: Decomposition Products: Hardener (clear side) Reactivity: Chemical Stability: Condition to Avoid: Substances to Avoid: Hazardous Reactions: Decomposition Products: 11. Hazardous polymerization does not occur. Carbon dioxide, carbon monoxide, oxides of nitrogen, and other organic compounds. This product is stable and non-reactive under normal conditions. Stable under normal storage conditions. High heat and open flame.
PAGE 6
CRACK-PAC® Injection Epoxy SAFETY DATA SHEET Mobility in soil: Further Information No data available. No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation potential, endocrine disruption, global warming potential) are expected from this product. 13. Disposal Consideration Waste Disposal of Substance: Container Disposal: Disposal of Cured Product: 14. Do not allow this material to drain into sewers/water supplies.
PAGE 7
CRACK-PAC® Injection Epoxy SAFETY DATA SHEET SARA 313 (TRI reporting) Chemical Name Naphthalene CAS Number 91-20-3 % by weight < 0.1 US State Right-To-Know Lists Massachusetts RTK Chemical Benzene-1,3-dimethaneamine (CAS 1477-55-0) Diethylenetriamine (CAS 111-40-0) New Jersey Work and Community RTK Act Pennsylvania Worker and Community RTK Law Listed Listed Listed Listed Rhode Island RTK US.
PAGE 8
CRACK-PAC® Injection Epoxy SAFETY DATA SHEET Additional Hardener (black side) Classifications NFPA Ratings HMIS Rating 1 3 0 HEALTH HAZARD 3 FLAMMABILTY HAZARD 1 PHYSICAL HAZARD 0 PERSONAL PROTECTION B Abbreviations ACGIH: CAS No.
PAGE 9
CRACK-PAC® Injection Epoxy SAFETY DATA SHEET 1. Identification Product Identification Product Identifier: Recommended Use: Use Restrictions: Company Identification Company: Address: CRACK-PAC® (ETIPAC10, ETIPAC10KT) Two Component Low Viscosity Injection Epoxy None Known. Simpson Strong-Tie Company Inc. 5956 W. Las Positas Blvd. Pleasanton, CA 94588, USA Phone: 1-800-999-5099 Website: www.strongtie.
PAGE 10
CRACK-PAC® Injection Epoxy SAFETY DATA SHEET Environmental Hazards: Signal Word: Hazard Statements: Precautionary Statements: Prevention: Response: Storage: Disposal: Skin Corrosion/Irritation Serious Eye Damage/Irritation Sensitization, Skin STOT, Single Exposure Acute Aquatic Environmental Hazard Chronic Aquatic Environmental Hazard Category 1B Category 1 Category 1 Category 1(corrosive to the respiratory tract) Category 3 Category 3 DANGER! Harmful if swallowed. Harmful in contact with skin.
PAGE 11
CRACK-PAC® Injection Epoxy SAFETY DATA SHEET Ingestion: Inhalation: Rinse mouth immediately. Give large amounts of milk or water, if person is conscious. Only induce vomiting at the instruction of medical personnel. Consult a physician. Immediately remove from further exposure. Get immediate medical assistance. For those providing assistance, avoid exposure to yourself or others. Use adequate respiratory protection. Give supplemental oxygen, if available.
PAGE 12
CRACK-PAC® Injection Epoxy SAFETY DATA SHEET 8. Exposure Controls / Personal Protection Personal Protective Equipment General Protection: Eye Protection: Hand Protection: Skin and Body Protection: Respirator Protection: General Hygiene: Wear appropriate personal protective equipment. Wear chemical splash goggles or safety glasses with side shield. Wear chemical-resistant gloves such as: Nitrile, neoprene, butyl. Wear long sleeve shirt/long pants and other clothing as required to minimize contact.
PAGE 13
CRACK-PAC® Injection Epoxy SAFETY DATA SHEET Hazardous Reactions: Decomposition Products: Hardener (clear side) Reactivity: Chemical Stability: Condition to Avoid: Substances to Avoid: Hazardous Reactions: Decomposition Products: 11. Hazardous polymerization does not occur. Carbon dioxide, carbon monoxide, oxides of nitrogen, and other organic compounds. This product is stable and non-reactive under normal conditions. Stable under normal storage conditions. High heat and open flame.
PAGE 14
CRACK-PAC® Injection Epoxy SAFETY DATA SHEET Mobility in soil: Further Information No data available. No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation potential, endocrine disruption, global warming potential) are expected from this product. 13. Disposal Consideration Waste Disposal of Substance: Container Disposal: Disposal of Cured Product: 14. Do not allow this material to drain into sewers/water supplies.
PAGE 15
CRACK-PAC® Injection Epoxy SAFETY DATA SHEET SARA 313 (TRI reporting) Chemical Name Naphthalene CAS Number 91-20-3 % by weight < 0.1 US State Right-To-Know Lists Massachusetts RTK Chemical Benzene-1,3-dimethaneamine (CAS 1477-55-0) Diethylenetriamine (CAS 111-40-0) New Jersey Work and Community RTK Act Pennsylvania Worker and Community RTK Law Listed Listed Listed Listed Rhode Island RTK US.
PAGE 16
CRACK-PAC® Injection Epoxy SAFETY DATA SHEET Additional Hardener (black side) Classifications NFPA Ratings HMIS Rating 1 3 0 HEALTH HAZARD 3 FLAMMABILTY HAZARD 1 PHYSICAL HAZARD 0 PERSONAL PROTECTION B Abbreviations ACGIH: CAS No.