Operation Manual
Table Of Contents
- AP300X INSTRUCTION MANUAL
- FRONT MATTER
- GENERAL INFORMATION
- Introduction
- How to use this manual
- System components
- Optional components
- NI300X NMEA Interface Unit
- CI300X Compass Interface
- Rudder" indicator
- Compass" Indicator
- CDI35 Course Detector Interface
- LF3000 Linear Feedback
- LFI3000 Linear Feedback Interface
- Robnet cables
- R3000X Remote Control
- S100 NFU steering lever
- S3 NFU steering lever
- JP300 Jack Point
- Mounting brackets
- Top mount bezel
- Flush mount bezel
- AP300X AUTOPILOT OPERATION
- Overview
- AP300X with MSD50 Stern Drive unit
- ON/OFF / Standby mode
- Automatic Steering
- Navigating with the AP300X
- Wind vane steering
- Automatic Speed selection
- Multiple station system
- Lock function
- The User Set-up Menu
- AP300DLX Main features
- Operation of Graphic Display
- Waypoints
- Routes
- Navigating with the AP300DLX
- Glossary
- INSTALLATION
- General
- RF300 Rudder feedback installation
- Junction unit installation
- Drive unit installation
- Control unit installation
- RFC35 Fluxgate Compass installation
- JP300 Jack Point installation
- R3000X Remote Control installation
- S3 NFU Lever installation
- S100 NFU Lever installation
- Interfacing
- Software Setup Procedure
- Sea Trial
- MAINTENANCE
- TROUBLE SHOOTING
- TECHNICAL SPECIFICATIONS
- AP300X AUTOPILOT SPARE PARTS LIST
Robertson AP300X Autopilot
34 22081814H
2.10 The User Set-up Menu
- SETUP -
- SETUP -
- SETUP -
- SETUP -
- SETUP -
Backlight
03
Contrast
05
Seastate
Filt.: OFF
NAV. source:
GPS 1
POS. Source:
GPS 1
NAV
SETUP
NAV
SETUP
Sequences
FWD in MENU
Sequences
BACK in MENU
Adjusts
b
acklight of display and pushbuttons in 10 steps.
(0 - dim, 10 - brightest). Setting is stored when system is
turned off, and resets to stored level at turn on.
Adjustment is local to the control head you adjust.
Adjusts contrast of displays in 10 steps. Setting is stored
when system is turned off, and resets to stored level at
turn on. Adjustment is local.
All steps not available at high temperature due to
automatic temperature compensation.
Selects the heading sensor used for AUTO steering.
Robertson
Scrolls through menu
selections or sets
value on menu items
Sets the Sea State filter.
OFF: Provides precise steering but increases rudder activity.
AUTO: Reduces rudder activity and reduces sensitivity o
f
autopilot in rough weather automatically.
MANUAL: Sets yawband manually.
OPTIONAL (only appears if configured for sailboat.
Selects whether NAV mode pushbutton will activate
NAVigation mode steering or WIND mode steering.
Selects the source for NAV mode steering as
configured in the INSTALLATION SETUP. (AP300DLX
always appears even if AP300DLX is not connected in the system).
Selects the source of position data used by the AP300DLX.
This option will appear whenever there is more than one
navigation receiver or position sensor connected to the
system. Selection of POS source is required only when an
AP300DLX is installed in the system, or if automatic speed
selection (HI/LO) is taken from a position source.
The menu will disappear after 60 seconds if no key is pressed,
or immediately if any mode key (STBY, AUTO, NAV) is pressed.
- SETUP -
Select Comp.:
RFC300 COMP.
- SETUP -
NAV/WIND func
Navigation
Test functions for analysing system data.
NMEA TEST?
SYSTEM DATA?
Quick double
press
Enter User
Setup Menu
Displays User
Set-up Menu
- SETUP -
Backlight
03
Robertson
TOP
Robertson
Robertson
Robertson
Robertson
Robertson
Robertson
Robertson
Robertson
BAC
K
FWD