User's Manual

5. Commissioning
5.1 Specic safety recommendations
Once the awning and Windy Hz Accel have been commissioned,
make sure that activation of Windy Hz Accel causes the awning to
be raised.
5.2 Recording of the sensor
See illustration E )
Take a remote control that is already programmed in the memory of -
the motor.
Press the PROG button on the remote control until the awning does a -
short up and down movement: the motor is in programming mode.
Press the PROG button (5) on the Windy Hz Accel sensor until the
-
awning does a short up and down movement: the Windy Hz Accel
sensor is programmed in the memory of the motor.
5.3 Pre-dened threshold adjustment method
See illustration F )
Set the potentiometer (4) to the desired threshold using a at -
screwdriver: 1 = high sensitivity to shaking; 9 = low sensitivity to
shaking
Insert the sensor (2) into the casing (1). -
Slide the sensor (2) onto the support (3) until the end stop: the sensor -
is set.
Check the adjustement and modify it in the event of incorrect sensitivity -
to shaking.
5.4 Personalized threshold adjustment method
See illustration H )
5.4.1 Adjustment to «Personalized threshold»
See illustration G )
Set the potentiometer (4) to 0 using a at screwdriver. -
Insert the sensor (2) into the casing (1). -
Slide the sensor (2) onto the support (3) until the end stop: the sensor -
is in «Personalized threshold» mode.
To Check the adjustment :
Shake the awning to simulate the maximum level of vibration permitted, -
until the awning rises automatically: the sensor is set and it switches to
demonstration mode.
Lower the awning then gently shake it to simulate the effect of wind; -
this should cause the awning to rise:
If the awning reacts satisfactorily, this means the sensor is set -
correctly,
If the awning does not react satisfactorily, stop the rising of the awning -
by pressing the STOP button and go to the next step «Changing the
threshold ajustement”.
5.4.2 Changing the threshold adjustment
Lower the awning. -
Release the casing and sensor assembly from the support (3) then -
wait for 2 secs.
Engage the casing and sensor assembly on the support (3): the -
sensor is in «Personalized threshold» mode.
If the casing and sensor assembly is disengaged from the support
for more than 4 seconds, re-engage it and then repeat the two
previous steps.
Shake the awning to simulate the maximum level of desired vibration,
-
until the awning rises automatically: the sensor is set.
6. Operation
6.1 When the wind comes up
When the wind comes up, the awning will start to vibrate. If the vibration
is greater than the set threshold, the awning will rise automatically:
It is impossible to prevent the awning from being raside and to lower
it until at least 30 secs after it has been raised.
6.2 When the wind dies down
When the wind dies down, the awning can be lowered using the remote
control after a time lag of 30 secs.
If the Windy Hz Accel sensor is linked to a sun sensor, the awning can
be lowered using the remote control after a time lag of 30 secs.
When the day is sunny and windy, deactivate the ‘Sun’ function so
as to protect the awning.
7. Repairs
7.1 Replacing of the batteries
See illustration D )
Never use rechargeable batteries to power the Windy Hz Accel
sensor.
The specic adjustments of the sensor are retained in the sensor’s
memory when batteries are changed.
Withdraw the sensor (2) from the support (3).
-
Remove the sensor (2) from its casing (1) using a at screwdriver. -
Replace the AAA alkaline batteries (6) with batteries of identical -
characteristics according to the polarity indicated: the LED will come on
for 1 sec to conrm that the batteries have been correctly inserted.
Replace the sensor (2) in its casing (1) and then on the support (3).
-
7.2 Deleting the sensor
See illustration I )
Follow the ‘Recording the sensor’ procedure to delete the sensor from -
the motor memory.
7.3 Disabling all the sensors.
Resetting disables all the sensors (sun, wind, etc) associated with
the awning motor.
Take a remote control recorded in the motor.
-
Give a long press on the PROG button on the remote control: the -
motor is in programming mode and performs a short up and down
movement.
Give a long press (7 seconds) on the PROG key of a sensor associated -
with the awning motor: the awning makes two short up and down
movements; all sensors are deleted in the motor’s memory.
7.4 Questions about the Windy Hz Accel ?
Observations Possible causes Solutions
The LED does not
come on after the
batteries have been
inserted.
The batteries are
incorrectly tted.
Check the direction
in which the batteries
are inserted into the
sensor.
The awning
does not rise
automatically when
the wind comes up.
The threshold is
incorrectly set.
Modify the threshold.
The threshold is
incorrectly set.
Modify the threshold.
Radio reception is
bad because there
is a metal obstacle
preventing radio
transmission.
Check that there are
no metal items near
the sensor.
The sensor or the
motor is out of
order.
Shake the awning to
raise it back up.
If this does not
happen,
replace the batteries.
If the awning still does
not move, check the
sensor and motor.
The awning rises
every 30 mins and
the LED is on all
the time.
The batteries are
low.
Replace the
batteries with
batteries of identical
characteristics.
Observations Possible causes Solutions
The awning rises
once an hour.
The sensor
is incorrectly
inserted in the
support.
Engage the sensor
into the support.
The radio link
between the
sensor and the
motor does not
work.
Replace the batteries
with ones having
exactly the same
characteristics. If the
awning still does not
rise, check the sensor.
The sensor is not
operating.
Replace the batteries
with ones having
exactly the same
characteristics.
If the awning
continues to rise,
replace the sensor.
7.5 Technical data
Power supply: 2 AAA alkaline batteries
Size: 25 x 38 x 153 mm (h x l x L)
Space between the oblong:
A = 93,5 mm B = 120,5 mm
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including
interference that may cause undesired operation.
Warning !
Changes or modications not expressly approved by the manufacturer
could void the user’s authority to operate the equipment.
h
L
l
A
B
EN
5
5
4
2
1
4
2
1
E
I
G
H
F
5070670A00_WINDY HZ ACCEL_EN.indd 2 26/11/10 10:21:59