. 2 (A)
Content sinaCAM Content 1. About this Document .............................................................................................................. 3 2. Safety Instructions .................................................................................................................. 4 2.1 Warning Signs and Indications ..................................................................................... 4 2.2 General Safety...................................................................
sinaCAM 1. About this Document About this Document Document Revision History Table 1: Revision History Revision Date 1.0 April 18, 2012 First edition Description 1.1 May 29, 2012 Amendment of power terminal (figures), system battery description, technical specifications. Minor text corrections. 1.2 (A) July 12, 2012 Alignment of contents in several chapters with the sinaCAM user manual, revision A.
Safety Instructions sinaCAM 2. Safety Instructions 2.1 Warning Signs and Indications CAUTION Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE Indicates a potentially hazardous situation which, if not avoided, may result in property damage. 2.2 General Safety 2.3 4 Read and follow all safety and operating instructions before installing and operating the camera system.
sinaCAM 3. Regulatory Compliance Always put the protection cap onto the lens mount when transporting the remote camera heads without lenses. Do not allow laser beams to enter the camera lens or the lens mount opening, as this could cause damage to the CCD sensor. Regulatory Compliance The sinaCAM base station and the sinaCAM remote heads comply with the following regulations: 4.
Description sinaCAM 6. Description 6.
sinaCAM 6.2 Description Base Unit HDC1-200 Figure 2: The Base Unit B B D B C B A Table 3: Item Elements of the Base Unit Designation Description A Control panel Controls and graphical user interface display B Mounting points M4 thread for attaching a handle or to fix the base unit to a mounting plate C System battery compartment The system battery supplies power to the internal clock only. It does not supply the camera with power. Do not open the system battery compartment.
Description 6.2.1 sinaCAM The Control Panel Figure 3: The Control Panel A B C F1 POWER D Table 4: Item 8 F2 E F G H Controls and their Functions Designation Description A USB 2.
sinaCAM 6.2.2 Description The Rear Panel Figure 4: Arrangement of the Terminals A B D C E F Table 5: Terminals on the Rear Panel Item Designation G H Description A Remote head terminals (1, 2) CoaXPress interface with 18 V power supply for the remote camera heads, connection via 75 ohms coaxial cable with BNC plug B SYNC (OUT, IN) Terminals for, e.g. an additional camera an external sync generator C HD-SDI output (1A, 1B) Terminals for, e.g.
Installation sinaCAM 7. Installation 7.1 Minimum System Requirements Shooting with sinaCAM requires the below listed minimum equipment: 7.
sinaCAM 7.5 Installation Connection Examples Figure 5: Standard Single-Link Setup 3D Monitor REC DC IN 12...24V REC EVF 3D Recorder Figure 6: (Electronic View Finder) Advanced Dual-Link Setup HD Monitor DL C RE Figure 7: Dual Link Recorder DC IN 12...24V DL C RE Dual Link Recorder Broadcast Setup Genlock OUT Genlock IN DC IN 12...24V LIVE Broadcast Quick Start Guide Remote Control Unit Rev.: 1.
The Menus at a Glance The Menus at a Glance F2 - Save F1 - S A FPS 50i Shutter FULL Gain ASA 200 WBalance 5600K Gamma&CM R709LEG LEVEL MODE SYS 24p; 24psf; 25p; 25psf; 50i; 30p; 30psf; 60i; 48pDL; 50pDL; 60pDL; 23,9p; 23,9psf; 29,9p; 29,9psf; 59,9i; 59,9pDL; 720 24p; 720 25p; ... 720 30p; 720 50p; 720 60p; 720 23p; 720 29p; 720 59p ... FULL; 1/50; 1/60; 1/125; 1/250; 1/500; 1/1000; 1/2000; 1/5000 ... ASA 200; ASA 400; ASA 800 ... 3200K; 4300K; 5600K; 6500K; USER ...
sinaCAM Operation 9. Operation 9.1 Switching ON and OFF After the base unit is connected to the power supply, the power LED glows red. Switching ON Push the power switch. – The power LED of the base unit changes from red to green. – The HOME menu screen comes on. – The system LED of the remote head lights up in orange, starts flashing green and finally glows green continuously. Note: The system LED of the remote head can indicate additional status information.
Technical Specifications 10. sinaCAM Technical Specifications Remote Head HDC1-100 Image Sensor 2/3” Single Chip Kodak CCD Sensor (RGB) 2004x1144 Pixels, Progressive Scan Sensitivity 2000 Lux @ f 8.0 / 0 dB Gain (100% video out) 160 Lux @ f 2.2 / 0 dB Gain (100% video out) Resolution 1920x1080 Pixels Dynamic Range 13.5 f-stops Signal/Noise Ratio 64 dB @ 0 dB Gain Interface CoaXPress, 75 ohms BNC Cable Max.
sinaCAM Technical Specifications Base Unit HDC1-200 HD-SDI Video Formats YCbCr 4:2:2 / 10 Bit 1920x1080 / 24p, 24psf, 25p, 25psf, 50i, 30p, 30psf, 60i, 48pDL*, 50pDL*, 60pDL*, 23.98p, 23.98psf, 29.97p, 29.97psf, 59.94i, 59.94pDL* * = HD-SDI Dual-Link Mode With May 2012 firmware update: 1280x720 / 24p, 25p, 30p, 50p, 60p, 23.98p, 29.97p, 59.
