SUPER® STRIPPER Operating Manual Read before use and keep safe Table of Contents 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.
1.0 Technical data/technical description Power supply Power consumption Number of strokes Sound pressure level Sound energy level Hand/Arm-Vibration Weight Comes with: 110-120V AC 2200W, 20A with current limitor 5000 strokes/min 93 dB(A) 106 dB(A) 6 m/s2 220 lbs Super® Stripper, 2 blades, ear & eye protection and tool kit. 2.0 Safety The Sinclair Super® Stripper is state of the art designed and meets all standard safety requirements. 3.
.2 Danger while working with the machine The Super® Stripper is designed to the highest technical standards. Incorrect use can be dangerous! Use this machine only: - As instructed in this operating manual. - With the machine in perfect working order. Disturbances that could impair safety have to be eliminated at once. 3.3 Restriction of use The Super® Stripper is exclusively for removing bonded floor covering in dry environments. It should not be used for any other purpose.
.0 Maintenance The Super® Stripper is virtually maintenance free. The guide shaft castings require lubrication from time to time. (After approx. 1650 sq. feet). Initially the machine is fully’ lubricated and should not require any additional lubrication for the first 5000 square feet. The zirc fittings are located on each side (see diagram). 1) To Grease the gearbox on its right side, remove left wheel and bottom cover. Spin axel/gearbox to expose zirc fitting.
Changing the driving wheels Remove the lynch-pins and pull the wheels from the axle. Do not loose the wheel key under any circumstances. 5.0 Use The Super® Stripper removes bonded, flexible floor covering in strips. This procedure corresponds with the customary method of using a hand floor scraper. The stripper works with a steel blade at a very high frequency, minimizing vibration and noise. The Super® Stripper is self propelled. The motor actuates both the blade and the machine movement.
.0 Information about various floorings CV-floorings, PVC-floorings and carpets without foam backing Cut strips of approx. 30 cm (12 inch) width. If the flooring is bonded very tight, cut strips smaller. The machine should remove the flooring without slipping wheels. Carpets with foam backing A sharp blade is essential in order to ensure the floor covering is removed together with the foam backing. Remove floorings across the width, particularly if you have any uneven sub-floor.
8.
59 60 61 63 64 65 66 67 68 69 70 71 72 73 74 75 76 78 79 80 81 82 83 84 85 86 87 88 92 93 94 95 97 98 100 101 102 1 24 6 1 1 1 1 1 2 2 2 2 1 1 1 1 2 1 1 1 1 2 1 1 1 5 4 1 1 1 1 6 1 4 2 1 2 Motor bracket Safety washer 8mm Elastic stop nut M8 Drive belt 187 L 100 Handle Bracket Handle Angle Brace Handle 88 Electrical short cord Cable Clip Nut Square nut Cyl Screw 8x45 Power cord w/plug Belt pulley ZZ 24 - large Belt pulley ZZ 12 - small Locknut M 10 Green weight handle Foam grip handle Switch Box Housing La
TURBO, EXTRO, SUPER, BRAVO, DURO & ECO STRIPPER 10
SUGGESTED BLADE SELECTION BRAVO/DURO/ECO STRIPPER #10-4906 8”Rigid. Our standard blade for removal of vinyl, carpet, adhesive, etc. Bevel edge of blade should be up for concrete and down for wood sub-surfaces. Precutting of carpet and vinyl needed. #10-4904 8”Flexible. Same as above, yet for uneven concrete surfaces and some soft foam back carpet. #10-4907T 8”Tile Blade. For use on VAT and VCT tile. Prevents tile from jamming in between blade and blade holder.
STANDARD WARRANTY SINCLAIR EQUIPMENT COMPANY’S tools are warranted to be free of defects in workmanship and materials for a period of one year from the date of original purchase. Should any trouble develop during this one year period, return the complete tool, freight prepaid, to SINCLAIR’S authorized Service Center. If inspection shows the trouble is caused by defective workmanship or materials, SINCLAIR EQUIPMENT COMPANY will repair, or, at its option, replace without charge.
