USER MANUAL Read the User Manual before operating the product, and keep the manual at a convenient place near the product. 3dprinter.sindoh.
Safety Instructions Be sure to observe the followIng instructions when using the device. Warning: Failure to observe the instructions may lead to death or serious injury. Directly plug the power cord in the receptacle on the wall. Do not use extension cord. If the power cable or plug is worn or damaged, pull out the power plug. The exposure of the interior of the machine can cause electric shock or burns. Do not remove covers or screws other than specified in this manual. Please be cautious.
Before use Thank you for purchasing our product. This user manual contains detailed information about correct use of device and easy maintenance to maintain the optimal state, and to contribute to the rationalization of office work of your company. Carefully read the user manual before using the device and keep close at hand. In order to use device correctly and safely, please carefully note the precautions before use. Prohibition and limitation 1.
Contents Before using the Machine 1. Preface--------------------------------------------------------------------------------------------------------------------------- 1 2.
Chapter 2 UI Menu Functions 1. UI Home Screen Functions--------------------------------------------------------------------------------------------- 2-2 1.1 Device Status Display------------------------------------------------------------------------------------------------------ 2-2 1.2 UI Function Control--------------------------------------------------------------------------------------------------------- 2-2 1.
1.4 Print Job Management --------------------------------------------------------------------------------------------------3-13 1.5 Printing with Two Types of Filamentst -------------------------------------------------------------------------------3-14 1.6 Changing Filaments -----------------------------------------------------------------------------------------------------3-14 Chapter 4 Printed Output Check 1.
Before using the Machine 1. Preface This User Manual describes detailed explanations and points to note in connection with operating and using the machine. Please read the User Manual carefully before using machine, and keep it for reference purpose. Important - The content of the User Manual is subject to change without any prior notification.
Before using the Machine 2. Conventions Symbols This manual uses the following symbols and meanings. Warning - Indicates importance safety notes. Ignoring these notes could result in serious injury or death. Be sure to read these notes carefully for your safe operations of the machine. Caution - Indicates important safety notes. Ignoring these notes could result in minor injury, or damage to the machine or to property.
Before using the Machine 3. Safety Information Plug the power cord into a properly grounded outlet which is near and quickly accessible from the machine. Do not use or place the machine in wet or humid environment. Caution Hot Surface - When you touch your body with this part, you are burned. - To avoid burns, follow the instructions below. The inside of the machine may be hot. To reduce the risk of injury from a hot component, allow some time to cool down.
Before using the Machine Caution Pain - To prevent personal injuries or damages to the machine, you need to follow the below instructions before moving the machine. Do not open the front and top door during machine operation. When the power is on, do not let any of your body touch the machine except the bed.
Before using the Machine 4. Precautions 4.1 Installation Warning - Install the machine in a well ventilated area. You can small odor during machine operation. It should not be harmful; however, if the area of where the machine is located is not ventilated, make sure to ventilate the area appropriately time to time. Important - Install the machine with its vents spaced at least 10 cm away from walls and other equipments.
Before using the Machine 4.2 Moving the Machine 1 Power off the device. 2 Disconnect the power cord and cables from the device. 3 Make sure that the FLEXIBLE bed and cartridge are installed in the device, and close the front and top doors. 4 Four people are required to hold the transport handles on both sides to move the device with the bottom facing down. Warning - Before moving the machine, be sure to unplug the power cord from the outlet.
Before using the Machine 4.3 Power Switch Before turning the power switch on, check that the power cord is connected to the socket tightly. Then, turn the power on by push the power switch to “│”(ON) position at the right on rear side of the Machine. To turn the power off, push the power switch to “○”(OFF) position. │for “ON” IEC 60417-5007 (DB:2002-10) ○ for “OFF” IEC 60417-5008 (DB:2002-10) The Switch used for this machine meets the requirements on the symbols and complies with its standard.
Before using the Machine 5. Consumables Handling Warning - Do not burn the Cartridge unit or filament. It may be a cause of big fire or burn by ignition. Caution - Keep them out of the reach of children. - If skin irritation occurs after touching the filament, please see a doctor. Important - Do not keep the cartridge unit in the following places.
Before using the Machine 5.3 Flexible When using flexible materials, clean the inside of the nozzle after the filament load. Even if the inside of the nozzle is cleaned, if the inside of the nozzle has debris, the nozzle may be clogged or the filament may be transported. (Refer to P. 5-3 “1.5 Cleaning the Inside of the Nozzle”.) Be careful because it is difficult to set the output condition compared with PLA and ABS materials. Warp or spider web may occur at output.
Before using the Machine 6. Instructions for Use Caution - The nozzle and the bed that are inside the machine are very hot during machine operation. Please be cautious not to touch the nozzle or the bed during removal of the printed objected or during inspection of the machine inside. It may become the cause of injuries or burns. - Never operate the machine in the way this manual does not specifically instruct.
Before using the Machine 7. Ventilation Caution - Use the machine in a place with good ventilation. If the machine is used in a place without good ventilation, this may be harmful for your health. Ventilate it on a regular basis. - Do not block vents. Inappropriate cooling may lead to high temperatures inside the machine. - In general, a new machine may produce small amount of gaseous components, so ensure good ventilation when the machine is used for the first time.
Before using the Machine 8. Notices ❖ Noise Emission Level The following are measured in accordance of ISO 7779 and reported to meet ISO 9296. Some modes may not be available in your purchased products.
Before using the Machine ❖ WLAN Notice Exposure to radio frequency radiation The following notice is applicable if your printer has a wireless network card installed. The radiated output power of this device is far below the FCC radio frequency exposure limits. A minimum clearance of 20 cm (8 inches) must be maintained between the antenna and any persons for this device to satisfy the RF exposure requirements of the FCC.
Before using the Machine 9. Disposal of Used Battery Control board uses a Lithium battery. Please discard used batteries following the environmentally friendly procedure stated on the manufacturer guidelines. To replace batteries, please contact a qualified service engineer.
Before using the Machine 10. Wifi Module Disclaimer ❖ This module includes a Wifi module, compatible only with Sindoh 3DWOX models. Wifi module inside Important - This Wifi module can cause radio interference, therefore it should not be used for any purposes related to human lives. - Do not expose this product to water, humidity or liquid. - Do not expose this product to direct light, hot temperature or fire.
Before using the Machine ❖ Precautions IEEE 802.11b : 2412MHz ~ 2462MHz Frequency IEEE 802.11g : 2412MHz ~ 2462MHz IEEE 802.11n(20MHz) : 2412MHz ~ 2462MHz IEEE 802.11n(40MHz) : 2422MHz ~ 2452MHz Antenna Power Density IEEE 802.11b : 10mW(10dbm)/MHz IEEE 802.11g : 10mW(10dbm)/MHz IEEE 802.11n(20MHz) : 10mW(10dbm)/MHz IEEE 802.11n(40MHz) : 10mW(10dbm)/MHz No. of Channels IEEE 802.11b : 11 IEEE 802.11g : 11 IEEE 802.11n(20MHz) : 11 IEEE 802.11n(40MHz) : 7 Modulation IEEE 802.11b : DSSS/CCK IEEE 802.
Before using the Machine 11. USB Memory Disclaimer ❖ FCC COMPLIANCE STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Before using the Machine ❖ IC Identification on Class of ITE CAN ICES-3 (B)/NMB-3 (B) DECLARATION OF CONFORMITY Product name : USB Flash Drive Model name : 8GB-WJ004, 4GB-WJ004 FCC Rules : Tested to comply with FCC Part 15, Class A Operating Environment : For HOME OR OFFICE USE FCC COMPLIANCE STATEMENT This device complies with part 15 of the FCC Rules.
3DWOX 5X / 7X USER MANUAL Preparations for Machine Operation 1
1 Preparations for Machine Operation 1. Machine Specifications 1.1 Printing Printing Method Fused Filament Fabrication Max. Print Length(mm) 5X : W(max):350, D(max):350, H(max):350 7X : W(max):370, D(max):390, H(max):450 W(max):380, D(max):390, H(max):450 (Expanded print mode) Print Layer Thickness Setting 0.05~0.4mm Basic Nozzle diameter 0.4mm Filament width 1.
Preparations for Machine Operation 1.5 1 Default Setting of Print layer Width Nozzle Width 0.4mm Print Layer Width 0.
1 Preparations for Machine Operation 2. Basic Components Please check all basic components are in the box. Caution - Please keep the box and packaging material; they are needed for product exchange or repair service.
Preparations for Machine Operation 3. 1 Understanding the Device Parts 5 12 11 4 6 3 2 13 8 7 1 9 10 No. Part Name Description 1 Front door handle A handle to open the front door. 2 USB port Connect USB flash drive containing printing information and print directly from USB flash drive. 3 LCD Control panel Screen used to control printer. Caution - Usage of printer is recommended after removing the protection film on LCD control panel.
1 Preparations for Machine Operation 3 4 1 1 2 No. Part Name Description 1 Bed height adjustment Knob Used to level the Flexible bed. 2 Removable bed handle Used to assemble and dismantle Flexible bed 3 Bed heater Heats the printables' bottom surface to stabilize it on the bed. 4 Flexible bed (bed sheet) Seating space for printable. It has both sides of A and B. - Side A is a general purpose sheet for various materials.
1 Preparations for Machine Operation 4. Installation(Product connection, Cartridge Setup and Software installation) 4.1 Device Connection 1 On the rear side of the machine, connect the power cable to the power socket. Next, connect the power cable to the power outlet. 2 Press the power button, located on top of the machine. 3 After main menu is displayed on the LCD screen, install the cartridge (Refer to UI manual “LOAD”).
1 Preparations for Machine Operation 3 When installation of the file is complete, a pop-up window shows up as picture below. Press [Next] button to initiate the installation of 3DWOX Desktop program. 4 Choose the destination location of the file and press [Next] to proceed. 5 The file gets saved and the installation starts.
Preparations for Machine Operation 1 6 After all installation is complete, you can see that the “3DWOX Desktop” created on the desktop of your computer.
3DWOX 5X / 7X USER MANUAL UI Menu Function 2
2 UI Menu Function 1. UI Home Screen Functions 1.1 Device Status Display Displays information about the current state of the device. 1 No. 2 Name 3 Description 1 Termperature Display Displays the current temperature inside the nozzle, bed and device. 2 Cartridge Status Display Displays the material, color, and remaining amount of the filament. Reference - Does not display the remaining amount while operating under "Open Material Mode".
UI Menu Function 1.3 2 Changing Screen / Application Functions You can change the screens or go to the application management screen for additional functions. Display Name Description Return Return to the previous page Home Return to the home screen Programs Enter to the program management screen. Programs You can change the screens or go to the application management screen for additional functions. No.
2 2.
UI Menu Function Information 2 NAME CHANGE NAME & PW MODEL NAME SERIAL NO. VERSION WEB SITE WIRED IP WIRED MAC IP WIRELESS IP WIRELESS MAC IP HISTORY Quick Guide 2.1 PRINT PRINT USB FILES STORED USB This function is to print files stored in the USB memory. 1 From the HOME screen press [Print].
2 UI Menu Function 2 Press the [USB] button, and select the file you want to print from the list. FILES STORED This function is to print files stored in the machine. 1 From the HOME screen press [Print].
UI Menu Function 2 2 Press the [Files Stored] button, and select the file you want to print from the list. 2.
2 UI Menu Function LOAD This function automatically loads filament to the Nozzle. 1 From the HOME screen press [Cartridge]. 2 Select the cartridge and press [Load] to load the cartridge.
2 UI Menu Function 3 When [OK] is pressed at the cartridge load confirming message, cartridge load will automatically proceed. The filament reaches to the nozzle and it is heated up to the specified temperature. Then the filament is inserted into the heated nozzle. After the process has finished, screen will automatically return to the [HOME] screen. UNLOAD This function automatically unloads filament from the nozzle. 1 From the HOME screen press [Cartridge].
2 UI Menu Function 2 Select the cartridge and press [Unload] to unload the cartridge. 3 When [OK] is pressed at the cartridge unload confirming message, cartridge unloading will automatically procceed. To remove filament, the nozzle is heated up to the specified temperature and the filament unload starts. After the filament has been removed, the screen will automatically turn to the [Unlock] screen to let the user remove the cartridge.
UI Menu Function 2 ❖ Unload PVA(PVA+), Flexible Filament. Follow the instructions when you unload soft-materials such as PVA(PVA+), Flexible. 1 From the HOME screen press [Cartridge]. 2 Select the cartridge and press [Unload] to unload the cartridge.
2 UI Menu Function 3 As shown in the following UI screen, remove the snap ring and tube from the nozzle and then press the [OK] button.
UI Menu Function 2 4 Cut the filament that came out of the tube as shown below and press the [OK] button. 5 Reinsert the tube into the nozzle and then install the snap ring. Push the tube toward the nozzle again. Then, press the [OK] button.
2 UI Menu Function 6 After the filament has been removed, the screen will automatically turn to the [Unlock] screen to let the user remove the cartridge. UNLOCK This Function is to remove the cartridge out of the printer. Cartridge unlock automatically initiates when filament unload is finished. Cartridge unlock can also be manually done by the user. ❖ When unlock screen automatically appears after cartridge unload.
UI Menu Function 2 ❖ To manually unlock later. 1 From home screen press [Cartridge]. 2 Select the cartridge and press [Unlock] to unlock the cartridge.
2 UI Menu Function 3 For 10 seconds [Lock] state is deactivated and the user can detach cartridge from printer. If the cartridge can’t be pulled out even after “unlock”, gently push it forward and then try to pull out again. 4 After 10 seconds printer will automatically change to [Lock] state and [Unlock] appears.
UI Menu Function 2.3 2 CLOUD This function enables calling and printing files stored in the server using cloud apps under network connection. 1 On the Home window, click the [Cloud] button. 2 Cloud apps available for users will be listed. Reference - For more details on the cloud function, see p. 3–8, “Cloud-based printing.
2 UI Menu Function 2.
UI Menu Function 2 Extruder This function is used to fine control the filament to its position. 1 From home screen press [Setting]. 2 Press [Extruder] to enter Extruder settings. 3 To Control [Extruder], Nozzle temperature needs to be raised. Press the [Cancel] button to cancel temperature increase during the operation.
2 UI Menu Function 4 Select the nozzle that you will use to move the filament. Press [10], [50], [100], [200] to select an amount. In the image shown below, press the direction to move the filament. Bed Leveling This function is used to perform the leveling of the bed. 1 From home screen press [Setting].
UI Menu Function 2 2 Press the [Bed Leveling] button to enter Bed Leveling settings. If the current Nozzle temperature is too high, process for cooling down the Nozzle temperature is added. 3 Leveling will be automatically done and after completion, the screen will return to its previous page.
2 UI Menu Function Z Offset ※ After bed leveling, it is highly recommended to check the z-offset. This Menu allows user to control the GAP in between Nozzle and BED. Standard is 0.25mm and can be customi zed. [+] button widens the GAP, [-] button shortens the GAP. ※ For higher adhesive strength between the print output and the bed, shorten the distance of the z-offset. For less adhesive strength, widen the distance of the z-offset. 1 From home screen press [Setting].
UI Menu Function 2 4 Use the [Move] and [Save] buttons to adjust the gap and to save the setting. The saved value is applied when next time the print starts. Nozzle Control Nozzle controls include [Nozzle Cleaning (Auto)], [Nozzle Cleaning (Manual)], [Nozzle Calibration], and [Nozzle Replacement]. Nozzle controls can be used to clean, correct the location of, and replace nozzles. 1 From home screen press [Setting].
2 UI Menu Function 2 Press the [Nozzle Control]. ❖ Nozzle Cleaning (Auto) Use Automatic nozzle cleaning to remove the remaining debris inside the nozzle. 1 Press [Nozzle Cleaning Auto] button to access nozzle cleaning settings. Select the nozzle that you want to clean.
UI Menu Function 2 3 In order to get rid of filament residue, the nozzle needs to be heated. When the specified temperature is reached, it moves on to the next step to remove filament residue. Once finished message will appear, printer will return to the settings screen.
2 UI Menu Function ❖ Nozzle Cleaning (Manual) Use Manual nozzle cleaning to remove the remaining debris inside the nozzle. 1 Press [Nozzle cleaning Manual] button to access nozzle cleaning settings. Select the nozzle that you want to clean. 2 Enter the temperature and press the [OK] button. Press the heating nozzle button to set the temperature of the nozzle.
UI Menu Function 2 3 Remove the nozzles to clean its interior. Press the [Nozzle Disconnect] and [Disconnect] button to disconnect the nozzle. Note - Refer to P.3-6 “Nozzle Cleaning” for the details of the operation of each button. - Refer to P.5-3 “1.5 Nozzle Inside Cleaning” for the details of cleaning inside nozzles. 4 Then press the [Connect] button to connect the nozzle.
2 UI Menu Function ❖ Nozzle Calibration The location of the nozzle can be corrected. ▣ Printing of the XY Calibration Patt 1 Press [Nozzle Calibration] button to access the Nozzle Calibration screen. 2 To print the XY calibration pattern, press the [XY Calibration] button.
UI Menu Function 2 3 Press the [Yes] button to access the XY Calibration printing screen. 4 When the temperature of the nozzle and the bed rises and reaches the target temperature, printing will begin. 5 When printing pattern is completed, enter the number of the line that is the most straight line among the lines printed by Nozzle # 1 and # 2 and press [Save] button. If there is no straight line, enter the number of the nearest straight line.
2 UI Menu Function 6 To print the pattern for the calibrating nozzle again, press the [Yes] button. Press the [No] button to return to the Home screen. Note - Generally, the use of PLA material is recommended when performing XY-Calibration. Inevitably, XY-Calibration using ABS material is also possible. After the calibration is complete, there may be remainders on the bed during the process of removing the calibration pattern. (Pattern marks do not affect the function of the bed.
UI Menu Function 2 2 Press the [Enter Pattern Value] button to access the Enter Pattern Value. 3 Enter the values for the horizontal and vertical lines. And press [Save] button. 4 To print the pattern for the calibrating nozzle, press the [Yes] button. Press the [No] button to return to the previous screen.
2 UI Menu Function ❖ Nozzle Change Follow the steps below when replacing a nozzle. 1 Press [Nozzle Change] button and access Nozzle Change screen. 2 Choose the nozzle for replacement. Once selected, the nozzle will move to a proper position for replacement.
UI Menu Function 2 3 Press the [Nozzle Disconnect] and [Disconnect] to disconnect the nozzle. 4 Once released, replace the nozzle. After installing the nozzle, press the [Connect] button to connect the nozzle. Note - Refer to P.5-21 “4.4 Nozzle Change” for the details.
2 UI Menu Function 2-34
UI Menu Function 2 X, Y, Z Use to change the positions of the X, Y axes of Nozzle, and the Z axis of Bed. 1 From home screen press [Setting]. 2 Press the [X,Y,Z] button to enter X, Y, Z. 3 Press either [0.1], [1], [10], [100]to select the length of trasnfer, and press the arrows to move the Bed and the Nozzle in the respective position. To move to each axis' home location, press [All], [X], [Y] or [Z].
2 UI Menu Function NETWORK This is a menu to configure users network setting. IP address can be set up manually or automatically via DHCP setting. Wifi network is also supported. 1 From home screen press [Setting]. 2 Press the [Network] button.
UI Menu Function 2 3 The default network setting is Wired (connection using LAN line). Press [DHCP] for automatic IP address setup. To manually input a fixed IP address press [Static] and enter an IP address. Press [Connect] to save the changes. Press the [Setup] button to set the Ethernet speed and full/half duplex mode for the network environment. In general, when set to [Auto], the speed and duplex/half-duplex mode are automatically selected for the network environment.
2 UI Menu Function 4 In any case to use Wifi press the [Wifi] button. Wifi setting can be turned ON or OFF. 5 To select a Wifi network, you can call up the list of available Wifi by pressing [Search Connections]. 6 Select a wireless network from the list to connect to the network. For a password-protected network, a dialog pops up and asks for the password. You can refresh the network list by clicking [Search Connections].
UI Menu Function 2 7 Once successfully connected to the selected Wi-Fi, [DHCP] and [Fixed] can be set the same as the wired setting. Once set, press the [OK] button to save the setting. Important - Using both network cable and Wifi module together is not recommended for electronic devices which can be connected to a network. Due to characteristics of network communication, data may not be processed properly when data is coming in via both wired and wireless network.
2 UI Menu Function Bed Lowering Use this function, in times of moving printer to a different location. Bed will be lowered to the bottom and will be locked into position. 1 Press [Setting] from the home screen. 2 Press the [Bed Lowering] button to enter Bed Lowering settings.
UI Menu Function 2 3 The bed will automatically be lowered. Cleaning Case Function used to clean out the case for the collected filament residue. 1 From home screen press [Setting]. 2 Press the [Cleaning Case] button to enter Cleaning Case settings.
2 UI Menu Function 3 After entering the screen, press [Start] button to automatically move the bed. Clear the case according to the image on the screen and press [OK] button to return to the home screen.
UI Menu Function 2 OPEN MATERIAL The OPEN MATERIAL enables the usage of a third-party filament without any cartridge and smart chip. In the cartridge mode, the filament is automatically loaded and unloaded in optimal conditions, with our filament and smart chip. On the other hand, the OPEN MATERIAL requires some manual operations by users for loading and unloading the filament. To use the OPEN MATERIAL, change the machine settings in the following procedure. Then, follow the UI guide to load the filament.
2 UI Menu Function 4 Check the pop-up notice and press the [OK] button. Caution - Improper usage of a third-party filament may cause device failure and poor printing quality. Therefore, it is important to create a correct gcode and apply it to a device by fully understanding the characteristics of a third-party filament, including the recommended printing temperature and speed. - As soft filament with shore hardness of 65 D or less (TPU, TPE, etc.
UI Menu Function 2 Although the supports open material mode, we recommend the use of Sindoh filament on the printer. The filament available for use in Open Material Mode is shown below.
2 UI Menu Function 3 Select the test file to print.
UI Menu Function 2 S/W Update With the printer connected to the internet user is able to download the latest software. 1 From the home screen, press [Setting]. 2 Press [Software Update] button. 3 Press the [Start Update] button, and printer will start updating. After it has finished, restart the printer and updates will be applied.
2 UI Menu Function General Setting This menu is used to set various statuses of the printer. 1 From home screen, press [Setting]. 2 Press the [General] button.
UI Menu Function Menu Description Active Leveling This function executes Bed leveling before printing starts and offset the bed leveling by moving the bed in the direction the Z-axis during the printing. On, Off Lamp Menu to configure settings for machine lamp. Always On, On only in Printing, Always Off, Note 2 Value - Lamp will be activated as connecting the Web Monitor Power Saving The volume level of beep sound can be adjusted using this menu.
2 UI Menu Function ❖ Time Setting It shows the time of the current device, which can be changed by a user. If set and the current times are different, it can be changed. ❖ Time Zone The current time zone is displayed, and it can be changed by a user. The current time zone is displayed, and it can be selected and changed by a user. Once a time zone is set, the device will reboot to set the time zone. ❖ E-mail The current printing state of the device will be captured and then e-mailed.
UI Menu Function Menu 2 Description E-mail Address The sender info to be seen by the recipient(e.g. sender@domain.com) The recipient can reply to this email address Address SMTP server address (e.g. smtp.domain.com) - This is the server address of the email service (xxxx@gmail.com) Port SMTP Server Port (e.g. 25) - Normally the port number 25, 587 or 465 is used. Due to the increased security, some service providers do not allow the use of port number 465.
2 UI Menu Function Under [E-mail], input the recipient email address(es) and select the number times that you wish to send the notification emails. Additional recipient addresses can be added by using semicolon. e.g. recipient1@test.com; recipient2@test.com; recipient3@test.com The maximum number of notification emails that can be sent is 10.
UI Menu Function 2 4 Scroll down and there is a "Allow less scure apps" criteria. Set it to "On" to enable the option. ▣ Printer Setting 1 Set "smtp.google.com" for the settings of the email address. 2 For Google, 25 and 587 ports are compatible. Caution - According to the service provider, the email address and port number may be changed. For more information please contact service administrator. FAQ With a network connection, the FAQ home page can be connected to check information.
2 UI Menu Function 2 Press the [FAQs] button to connect to the FAQ home page. 3 The FAQ home page will be displayed, and the user can check any information.
UI Menu Function 2.5 2 Information INFORMATION NAME CHANGE NAME & PW MODEL NAME SERIAL NO. VERSION WEB SITE WIRED IP WIRED MAC IP WIRELESS IP WIRELESS MAC IP HISTORY Quick Guide In this menu user is able to view the detail information of the printer, and set device name & password. In [HISTORY] screen, user is able to view all the records of past works. 1 From home screen, press [Info]. 2 To set password and name for printer, select [Change Name & PW].
2 UI Menu Function 3 By entering the password, you can edit name and set a new password. Pressing [Save] saves the changes. Reference - Initial password is ‘0000’. - Password is used for security function and web monitoring function. 4 2-56 In [Info] screen, press [History] to access to view all the records of past works.
UI Menu Function 2 Quick Guide The quick guide for this device can be glanced at. 1 Press the [Quick Guide] button in the home screen to access the quick guide screen. 2 Press a button on the left side to see the description of individual items.
3DWOX 5X / 7X USER MANUAL Printing 3
3 1. Printing Printing User can print printables via USB flash drive, USB cable, or over the network. The following on the printer means it is ready to start print. 1.1 Printing from USB Flash Drive 1 Connecting USB flash drive to the printer. In order to print using an USB flash drive, insert the flash drive into the USB port. When the USB flash drive is connected while in the home screen, a list of files in the USB appears.
Printing 3 2 Printing Files Select a file to print in the USB list. 3 Print Preview Once selected, a preview of the model appears on the screen. 4 Printing Once [Print] is pressed the nozzle starts to be heated. When the specified temperature is reached, the printing starts.
3 Printing 5 Pausing Print Pressing [Pause] during a print will pause the progress. Press [Resume] again and nozzle is heated again, and the printer will continue printing.
Printing 3 6 Additional Functions of Pausing When the [Pause] button is pressed during printing, buttons appear in the upper right corner to execute additional function actions. Additional functions include [Nozzle cleaning], [Bed Height Adjustment], [Extruder], [Cartridge] and so on. These additional functions are used for any mechanical problem or if the user needs them.
3 Printing ❖ Nozzle Cleaning ① This menu can be used to clean a nozzle manually if the filament does not come out of the nozzle for printing. ② Select a nozzle to clean. ③ Enter the temperature and press the [OK] button. Press the heating nozzle button to set the temperature of the nozzle. ④ Press the [1], [10], [50], or [100] button to select the desired moving amount. ⑤ Press an arrow button to move the filament to a desired direction.
Printing 3 8 Printing Completion After printing has completed, follow the instructions and remove the printed product. Press the [OK] to return to home screen. Caution - Do not touch the bed or the output until the bed has cooled down. - To remove the printed output before the bed is cold, press the [Cancel] button, wear protective gear, and then remove the output.
3 Printing Reference - Methods of removing printables refer to P. 4-2 “1. Printed Output Check”. 1.2 Printing Via PC 1 Prepare PC connected to the same network where the printer is connected to. 2 Run 3DWOX Slicer program. 3 Press the [Print] button. 4 Following Steps (Same as steps 3~9 of printing via USB) Note - Pause, print cancelation, please refer to P.3-2 Printing from USB Flash Drive. - Refer to “3DWOX Desktop Manual” for the details. 1.
Printing 3 *Additional cloud apps can be added later. 2 When using [CLOUD] for the first time, users must register their printer. * Alexa and Sindoh Cloud Slicer app share Printer registration information. 3 [Generate Code] allows you to connect the device with the account of the user registered in the App. If there is a user registered on the device, [Registered Users] appears, listing the registered users and deleting them by clicking the [ - ] button.
3 Printing 4 When the print job is sent to the printer registered in the app, a menu called [Print Queue] appears, and the names of the sender and the transmitted print job are displayed in the list when the menu is entered. The transferred print job can be deleted with the [ - ] button.
Printing 3 5 When you select the print job you want to print, the preview image of the print job will be displayed, and by clicking the [Print] button, the print job starts immediately after downloading the corresponding output. When the printing is started, the print job in [Print Queue] will be deleted from the list.
3 Printing 6 [Printer Detail] menu lets users check the printer information. 7 [Edit Printer] menu lets users change the [Display name].
Printing 3 8 [Deregister Printer] menu lets users delete the registered printer in the server. * If users delete the printer information, the [Print queue] list and the registered user list will be initialized. * If users want to use the [CLOUD] function again after deletion, printer must be re-registered in the server. 1.4 Print Job Management You can manage print jobs in queue. 1 Press the [Job List] button on the upper right hand corner while printing. 2 The print jobs in queue are listed.
3 Printing 3 You may click the list to look at the information of the print job and delete it if necessary. 1.5 Printing with Two Types of Filaments 1 Two nozzles can cross print the same material. - PLA & PLA - ABS & ABS 2 Two nozzles can cross print the same material. - PLA and PVA(PVA+) 1.
3DWOX 5X / 7X USER MANUAL Printed Output Check 4
4 Printed Output Check 1. Printed Output Check 1.1 Detaching Printed Output Note - If Side B of the FLEXIBLE bed is used, the Printed Output can be detached when the bed cooled down, without detaching the FLEXIBLE bed. - If Printed Output is large that doesn’t detached on its own, detach the flexible bed after the bed has cooled down, and detach the Printed Output by bending the bed up and down. (Scraper is not required). To safely detach the printed model, first let the bed cool down.
Printed Output Check 4 Detach the object from the Flexible Bed. The object can be easily detached by bending the Flexible Bed up and down. Using the scrapper provided with the printer will be useful. Be careful not to apply too much pressure while using the scrapper could damage the bed sheet and the bed. Depending on the filament material the printed output may easily break or damage, please be cautious.
4 Printed Output Check 1.2 PVA(PVA+) Filament Removal Guide 1 After printing a model with PVA supports, Detach the printed output from the bed, and then soak it in water. Once it’s soaked in water, the PVA support will get dissolved. - If the water is warm, the dissolution time can be shorten. Make sure to keep the water temperature doesnot exceed 35°C; otherwise, the shape of the PLA can be deformed due to hot temperature..
Printed Output Check 4 Nozzle Z-offset calibration sheet Z-offset calibration sheet Bed - When ABS materials are output - If outputs are not properly attached to Side B, use only Side A, or carry out printing by adding the raft setting at the slicer. - When one or more arranged small outputs (50 mm × 50 mm or smaller) that have a small area at which they attach to the bed are printed out, it is recommended to print by adding the raft setting to Side A.
4 2. Printed Output Check If problems persist 1 Please visit http://3dprinter.sindoh.com.
3DWOX 5X / 7X USER MANUAL Maintenance 5
5 Maintenance 1. Machine Cleaning 1.1 Cleaning Case Maintenance When the filament residue is filled in the cleaning case, use the “Setup - Cleaning Case” menu to clean the cleaning case. 1.2 Printer Interior Cleaning Over time, there will be a build up of filament residue within the printer. If the residue goes into conveyor belt or fan wings, it can cause printer malfunction. Please clean the inside of the printer regularly or right after a print job. 1.
Maintenance 1.5 5 Cleaning the inside of the Nozzle The leftover in the nozzle interferes with filaments transfer. This interference can cause problems with printing and filament loading. The leftover makes the printing filament uneven or clogs the nozzle. Once melted, the filament can have different properties from the original. If the leftover in the nozzle is repeatedly heated / cooled, the properties will be changed. The changed leftover is harder to pull out, and easily stacked in the nozzle.
5 Maintenance 3 Remove the tube from the nozzle.. TUBE TUBE HOLDER 4 In the home screen, press the [Settings]-[Nozzle Control]-[Nozzle Cleaning (Manual)] buttons to access the nozzle cleaning menu.
Maintenance 5 5 After positioning the nozzle in the center, insert the enclosed Tube for Cleaning into the nozzle.
5 Maintenance 6 Enter the temperature and press the [OK] button. Press the heating nozzle button to set the temperature of the nozzle. Once the target temperature is reached, put a PLA filament into the tube and make it come through the nozzle. Note - Use a white PLA filament longer than 50cm for cleaning. - Use a white PLA filament to distinguish dirt from the nozzle easily. - Filaments have different characteristics based on their colors.
5 Maintenance 7 Remove the tube for cleaning and then pull out the PLA filament. 8 Press the [Disconnect Nozzle] - [Disconnect] buttons to remove the nozzle. As shown in the image, insert a nozzle cleaning tool into the top hole to remove dirt. Caution - When you pull out the filament, if you can not pull it out well, please heat the nozzle after removing it.
5 Maintenance 9 Remove the nozzle cleaning tool and reassemble the nozzle. Assemble the nozzle and then press the [Connect] button in the UI to reconnect it. Once connected, heat the nozzle again, as explained in Step 6. 1 10 Press the home button in the UI to lower the temperature of the nozzle. Slowly push the PLA filament until the nozzle temperature is 180 °C 11 If the nozzle temperature is between 80 ~ 90 ° C, remove the tube and pull out the PLA filament.
Maintenance 5 12 Repeat from step 3 until the filaments are free of contaminants as shown below. If cleaned filament comes out with no contaminants as shown in the figure on the left below, the nozzle cleaning is complete. Cleaned Filament Contaminated Filament 13 Assemble the tube and the snap ring in reverse order from step 3 to step 1, and then turn the lever to its original position.
5 Maintenance In the nozzle cleaning (manual) menu, with the nozzle heated, insert the nozzle cleaning spring from the nozzle inlet side and pivot it from side to side. Caution - Be careful. It may cause burns. - The tip of the nozzle may be hot. Please wear it with heat-resistant gloves. 1.6 Nozzle Tip Cleaning 1 In the home screen, press the [Settings]-[Nozzle Control]-[Nozzle Cleaning (Manual)] buttons to access the nozzle cleaning menu.
Maintenance 5 2 Press the [Heat Nozzle] button, and center it once the nozzle reaches the target temperature.
5 Maintenance 3 Wipe the tip of the nozzle with cotton or leather cloth in the direction shown below. Caution - To prevent burns, wipe the nozzle tip by folding the cloth several times. - Be careful not to damage the silicone adhesive between the nozzle and the silicon cap.
Maintenance 2. 5 Error Message and Solutions Message Description What To Do Booting Please wait until booting is complete. Message means on the first boot user must wait until the booting is finished. Once the boot up process is over and machine is ready, this message disappears automatically. EC 301, 302, 303, 304, 305, 306, 308, 351, 353, 355 There is a problem with the nozzle temperature sensor or heater If the problem persists after rebooting the printer, request for A/S.
5 Maintenance Message 5-14 Description What To Do Notification 434 The filament has already been consumed. Replace the smart chip. (Check if the smart chip was replaced with the filament.) Notification 438, 439 Cartridge Smartchip Error Smartchip Replacement Required. (Check if the smartchip was replaced as replacing the filament.) Notification 447 This error occurs if a newly loaded filament material differs from the previous printing filament material.
Maintenance 3. Problems and Solutions 3.1 In Cases where Filament is Cut Between the Extruder and Nozzle 5 1 Remove the snap ring from the fitting of the nozzle part and then the tube. Move the filament toward the nozzle to push out the broken part in the extruder operation mode. Remove all broken parts, install the nozzle to the tube, and install the snap ring. ※ Push in the tube until the black section of it is fully inserted.
5 Maintenance 3.3 Solution for Notification 401, 601 The Notification 401, 601 error code occurs if the filament was not correctly transferred. There are many possible reasons why the filament was not properly transferred. To solve this issue, follow the instructions below. 1 Press the [OK] button to move the printing screen. Then, press the [Pause] button followed by the [Function] button located on the top of the screen.
Maintenance 5 3 Select the [Extruder] menu. Wait until the nozzle’s temperature reaches the target temperature. Operate the extruder to insert the filament by 50 mm. (If the filament was not injected, repeat step 2 for two to three times. If this does not work, please contact our customer service hotline, and submit a video or image of this issue to a customer service representative.
5 Maintenance 4 A persistent Notification 401, 601 error code may be caused by an insufficient space between the nozzle and the bed, which causes the filament not to be correctly transferred. In such a case, select the [Bed Height Adjustment] menu to adjust the height of the bed so that there is adequate space between the nozzle and the bed. ※ You can also cancel printing and re-execute [Setting]–[Bed Leveling] to set the correct space between the nozzle and the bed.
Maintenance 4. Replenishing Consumables 4.1 Bed Replacement 5 Removing Flexible Bed Reference - Please refer to P. 4-2 “1.1 Detaching Printed Output”. Installing Flexible Bed Reference - Please refer to P. 4-2 “1.1 Detaching Printed Output”.
5 Maintenance 2 Pull the filter toward the direction of the arrow to remove it. 3 Install a new filter, as shown in the image. 4 Close the top door.
Maintenance 4.3 5 Cartridge Replacement Replace cartridge when a cartridge is used up or a different color/material is needed. 1 Initiate Cartridge Unload. Reference - For details on cartridge unload, please refer to P. 2-7 “UNLOAD” 2 Please switch the cartridge first and then load. Reference - For details on cartridge load, please refer to P. 2-5 “LOAD” Note - When replaced with a different color, the previously used color may be seen in the beginning of printing.
5 Maintenance 2 As shown in the image, turn left the nozzle fixing lever on top and then pull down the nozzle while pressing both hooks to remove it. 1 3 Install a new nozzle and then turn right the nozzle fixing lever on top. Once the nozzle is installed, press the [Connect] button in the UI to reconnect it.
Maintenance 4.
5 Maintenance 2 Match one end of a new pad as shown in the following figure, and push it in the arrowed direction. 3 After inserting the pad, check that the pad is held by the hooks in three directions, as shown in the following figure. Caution - When replacing pads, be careful not to damage or deform adjacent parts.
3DWOX 5X / 7X USER MANUAL Appendix 6
6 1. Appendix Type of Filaments (Material, Color) PLA(700g) Color: White, Black, Gray, Red, Yellow, Green, Blue, Pink, Purple PLA(1.
Appendix 2. 6 Using an open material Note - For setting the product on using an open material, see p. 2–39, “Open material.” - In the case of the 7X model, you can select a position to insert the spool during the setting of the Open - Material mode. If you are to use any soft or brittle material, make sure to select [Top]. 2.1 Installing from the front 1 On the Home window, click the [Spool] button.
6 Appendix 3 Enter the material and output temperature of the filament, then click [OK]. Caution - If the material and temperature are entered incorrectly, the machine may be damaged during the loading process. 4 After confirming that you will run cartridge loading, clicking [OK] will run filament loading. When the temperature reaches the specified target value, push the filament in fully through the front entry, then click [OK].
Appendix 6 6-5
6 2.2 Appendix Installing from the top Important - In the case of the 5X model, follow the “Installing from the front” procedure because installing from the top is not possible. - Referring to the enclosed “Spool stand instructions,” install the spool stand at the top of the machine, then carry out the following procedure. 1 Open the top door, and remove the tube guiding rod. 2 Pull the snap rings out from the nozzles, then pull the tubes out.
Appendix 6 3 Insert the enclosed cleaning tubes into the nozzles. Tube for Cleaning 4 Click the [Spool] button on the Home window. 5 Select the filament to be activated by clicking either [Filament 1] or [Filament 2].
6 Appendix 6 Enter the material and output temperature of the filament, then click [OK]. 7 After confirming that you will run cartridge loading, clicking [OK] will run filament loading. When the temperature reaches the specified target value, push the filament in fully through the front entry, then click [OK]. Filament loading will run automatically, and upon completion, it will automatically return to the Home window.
Appendix 6 6-9
6 Appendix Important - To return to the Cartridge mode, carry out the following procedure: Install the tube guiding rod at the original position. Remove the cleaning tubes that were inserted into the nozzles, then reconnect the existing tubes. In reconnecting the existing tubes to the nozzles, make sure that the tubes span on the guiding rod. Connect the left tube to the left nozzle then the right tube to the right nozzle.
Notice to Users Type Class A equipment (commercial telecast equipment) Class B equipment (domestic telecast equipment) Notice This equipment is a Class A EMC (electromagnetic compatible) equipment, and should not be used in household locations This equipment is a Class B EMC (electromagnetic compatible) equipment, for household purposes, available to be used in any location. This Product is a Class A equipment.
