3DWOX 5X / 7X/ riZE 7XC USER MANUAL Maintenance 5
5 Maintenance 1. Machine Cleaning 1.1 Cleaning Case Maintenance When the filament residue is filled in the cleaning case, use the “Setup - Cleaning Case” menu to clean the cleaning case. 1.2 Printer Interior Cleaning Over time, there will be a build up of filament residue within the printer. If the residue goes into conveyor belt or fan wings, it can cause printer malfunction. Please clean the inside of the printer regularly or right after a print job. 1.
Maintenance 1.5 5 Cleaning the inside of the Nozzle The leftover in the nozzle interferes with filaments transfer. This interference can cause problems with printing and filament loading. The leftover makes the printing filament uneven or clogs the nozzle. Once melted, the filament can have different properties from the original. If the leftover in the nozzle is repeatedly heated / cooled, the properties will be changed. The changed leftover is harder to pull out, and easily stacked in the nozzle.
5 Maintenance 3 Remove the tube from the nozzle.. TUBE TUBE HOLDER 4 In the home screen, press the [Settings]-[Nozzle Control]-[Nozzle Cleaning (Manual)] buttons to access the nozzle cleaning menu.
Maintenance 5 5 After positioning the nozzle in the center, insert the enclosed Tube for Cleaning into the nozzle.
5 Maintenance 6 Enter the temperature and press the [OK] button. Press the heating nozzle button to set the temperature of the nozzle. Once the target temperature is reached, put a PLA filament into the tube and make it come through the nozzle. Note - Use a white PLA filament longer than 50cm for cleaning. - Use a white PLA filament to distinguish dirt from the nozzle easily. - Filaments have different characteristics based on their colors.
5 Maintenance 7 Remove the tube for cleaning and then pull out the PLA filament. 8 Press the [Disconnect Nozzle] - [Disconnect] buttons to remove the nozzle. As shown in the image, insert a nozzle cleaning tool into the top hole to remove dirt. Caution - When you pull out the filament, if you can not pull it out well, please heat the nozzle after removing it.
5 Maintenance 9 Remove the nozzle cleaning tool and reassemble the nozzle. Assemble the nozzle and then press the [Connect] button in the UI to reconnect it. Once connected, heat the nozzle again, as explained in Step 6. 1 10 Press the home button in the UI to lower the temperature of the nozzle. Slowly push the PLA filament until the nozzle temperature is 180 °C 11 If the nozzle temperature is between 80 ~ 90 ° C, remove the tube and pull out the PLA filament.
Maintenance 5 12 Repeat from step 3 until the filaments are free of contaminants as shown below. If cleaned filament comes out with no contaminants as shown in the figure on the left below, the nozzle cleaning is complete. Cleaned Filament Contaminated Filament 13 Assemble the tube and the snap ring in reverse order from step 3 to step 1, and then turn the lever to its original position.
5 Maintenance In the nozzle cleaning (manual) menu, with the nozzle heated, insert the nozzle cleaning spring from the nozzle inlet side and pivot it from side to side. Caution - Be careful. It may cause burns. - The tip of the nozzle may be hot. Please wear it with heat-resistant gloves. 1.6 Nozzle Tip Cleaning 1 In the home screen, press the [Settings]-[Nozzle Control]-[Nozzle Cleaning (Manual)] buttons to access the nozzle cleaning menu.
Maintenance 5 2 Press the [Heat Nozzle] button, and center it once the nozzle reaches the target temperature.
5 Maintenance 3 Wipe the tip of the nozzle with cotton or leather cloth in the direction shown below. Caution - To prevent burns, wipe the nozzle tip by folding the cloth several times. - Be careful not to damage the silicone adhesive between the nozzle and the silicon cap.
Maintenance 2. 5 Error Message and Solutions Message Description What To Do Booting Please wait until booting is complete. Message means on the first boot user must wait until the booting is finished. Once the boot up process is over and machine is ready, this message disappears automatically. EC 301, 302, 303, 304, 305, 306, 308, 351, 353, 355 There is a problem with the nozzle temperature sensor or heater If the problem persists after rebooting the printer, request for A/S.
5 Maintenance Message 5-14 Description What To Do Notification 434 The filament has already been consumed. Replace the smart chip. (Check if the smart chip was replaced with the filament.) Notification 438, 439 Cartridge Smartchip Error Smartchip Replacement Required. (Check if the smartchip was replaced as replacing the filament.) Notification 447 This error occurs if a newly loaded filament material differs from the previous printing filament material.
Maintenance 3. Problems and Solutions 3.1 In Cases where Filament is Cut Between the Extruder and Nozzle 5 1 Remove the snap ring from the fitting of the nozzle part and then the tube. Move the filament toward the nozzle to push out the broken part in the extruder operation mode. Remove all broken parts, install the nozzle to the tube, and install the snap ring. ※ Push in the tube until the black section of it is fully inserted.
5 Maintenance 3.3 Solution for Notification 401, 601 The Notification 401, 601 error code occurs if the filament was not correctly transferred. There are many possible reasons why the filament was not properly transferred. To solve this issue, follow the instructions below. 1 Press the [OK] button to move the printing screen. Then, press the [Pause] button followed by the [Function] button located on the top of the screen.
Maintenance 5 3 Select the [Extruder] menu. Wait until the nozzle’s temperature reaches the target temperature. Operate the extruder to insert the filament by 50 mm. (If the filament was not injected, repeat step 2 for two to three times. If this does not work, please contact our customer service hotline, and submit a video or image of this issue to a customer service representative.
5 Maintenance 4 A persistent Notification 401, 601 error code may be caused by an insufficient space between the nozzle and the bed, which causes the filament not to be correctly transferred. In such a case, select the [Bed Height Adjustment] menu to adjust the height of the bed so that there is adequate space between the nozzle and the bed. ※ You can also cancel printing and re-execute [Setting]–[Bed Leveling] to set the correct space between the nozzle and the bed.
Maintenance 4. Replenishing Consumables 4.1 Bed Replacement 5 Removing Flexible Bed Reference - Please refer to P. 4-2 “1.1 Detaching Printed Output”. Installing Flexible Bed Reference - Please refer to P. 4-2 “1.1 Detaching Printed Output”.
5 Maintenance 2 Pull the filter toward the direction of the arrow to remove it. 3 Install a new filter, as shown in the image. 4 Close the top door.
Maintenance 4.3 5 Cartridge Replacement Replace cartridge when a cartridge is used up or a different color/material is needed. 1 Initiate Cartridge Unload. Reference - For details on cartridge unload, please refer to P. 2-7 “UNLOAD” 2 Please switch the cartridge first and then load. Reference - For details on cartridge load, please refer to P. 2-5 “LOAD” Note - When replaced with a different color, the previously used color may be seen in the beginning of printing.
5 Maintenance 2 As shown in the image, turn left the nozzle fixing lever on top and then pull down the nozzle while pressing both hooks to remove it. 1 3 Install a new nozzle and then turn right the nozzle fixing lever on top. Once the nozzle is installed, press the [Connect] button in the UI to reconnect it.
Maintenance 4.
5 Maintenance 2 Match one end of a new pad as shown in the following figure, and push it in the arrowed direction. 3 After inserting the pad, check that the pad is held by the hooks in three directions, as shown in the following figure. Caution - When replacing pads, be careful not to damage or deform adjacent parts.
3DWOX 5X / 7X/ riZE 7XC USER MANUAL Appendix 6
