Sindoh A1SD Series User Manual ● ● This user manual contains the product warranty inside. Please read this user manual before using this product and keep the manual nearby. 3dprinter.sindoh.
Safety Instructions Please make sure to follow the instructions below when using the machine. Warning: Failure to observe the instructions may lead to death or serious injury. Do not plug the power cord into extensions. Plug the cord directly into the wall socket. If the power cable or plug is worn or damaged, pull out the power plug. The exposure of the interior of the machine can cause electric shock or burns. Exposure to inside the machine can cause electric shocks or burns.
Before using the machine Thank you for purchasing our product. This user manual contains detailed information about correct use of machine and easy maintenance to maintain the optimal state, and to contribute to the rationalization of office work of your company Please carefully read the user manual before using the machine and keep close at hand. In order to use the machine correctly and safely, please carefully note the precautions before use. Prohibition and limitation 1.
Contents Before using the machine 1. Preface------------------------------------------------------------------------------------------------------------------- 1 2. Conventions ----------------------------------------------------------------------------------------------------------- 2 Symblos ------------------------------------------------------------------------------------------------------------------ 2 3.
1.2 Installed Resin-------------------------------------------------------------------------------------------------------- 2-4 1.
Chapter 5. Maintenance 1. Machine Cleaning--------------------------------------------------------------------------------------------------- 5-2 1.1 Printer Interior Cleaning-------------------------------------------------------------------------------------------- 5-2 1.
Before Using the Machine 1. Preface This user manual describes detailed explanations and points to note in operating the machine. Please read the user manual very carefully before starting use of the machine, and keep it for reference purpose at close. Important - The content of the user manual is subject to be changed without any prior notifications.
Before Using the Machine 2. Conventions Symbols The following symbols are used in this manual and their definitions are as follow. Warning - Indicates important safety notes. Ignoring these notes could result in serious injury or death. Be sure to read these notes carefully for your safe operations of the machine. Caution - Indicates important safety notes. Ignoring these notes could result in minor injury or damage to the machine or to property.
Before Using the Machine 3. Safety Information Please plug the power cord into a properly grounded outlet with is near and quickly accessible from the machine. Do not use or place the machine in wet or humid environment. This machine is very sophisticated 3D printing machine, so please keep in mind the following safety information for safe use. Caution Prohibition of Arbitrary Modification by Users or 3rd Party - Do not modify the machine at user’s will in any cases.
Before Using the Machine Caution Electric Shock - Contact with this part may result in electric shock. - To avoid electric shocks, follow the instructions below. Proceed your work after turning off the machine and unplugging the power cord from the outlet in case of accessing the system board, or installing hardware or optional memory devices. If some other device is connected with the machine, turn the machine off and separate the cables from the machine.
Before Using the Machine 4. Precautions 4.1 Installation Caution Injury Hazard - Install the machine in a well ventilated area. - You can smell odor during the operation. It should not be harmful, but if the area of the place where the machine is located is not well ventilated, make sure to ventilate the area appropriately periodically. - Place the machine in the place where it can’t be touched by children, pets, etc to prevent any accidents.
Before Using the Machine 4.2 Leveling Machine Install the printer on a flat surface. If the printer is not leveled, irregular noise and vibration may occur, resulting in splash resin or printing failure. This product has four screws for the purpose of leveling. The printer can be leveled by turning them according to the indication of the built-in level. For more details of leveling, refer to “Level Printer of 2. UI Menu Function”.
Before Using the Machine 4.3 Moving the Machine 1 Turn off the power by pressing power button. 2 Unplug the power cord and all cables connected to the machine. 3 Make sure if resin tank is removed. Otherwise, resin in the resin tank may overflow. 4 Lift the machine using handles located in the left/right side of the machine. Two people must work together using their both hands because the machine is very heavy.
Before Using the Machine 5. Handling Consumables Warning - Isopropyl alcohol can be flammable, even explosive.. Any containers holding isopropyl alcohol should be kept closed or covered when not in use because it is highly volatile. it should be kept away from heat, fire or sparks. Caution - Keep consumables out of reach of children, pet, etc. - If skin irritation occurs after touching resin, please see a doctor.
Before Using the Machine 5.1 SLA Resin (Photo Curable Resin) Please be cautious of the followings when handling Resin. - Wear nitril gloves all the time while handling the resin. - Resins being used for this machine should not be used for the food, drink and medical purposes. - Do not eat or inhale resin in any forms. Be careful not to let the resin enter your body through eyes or nose. - Do not expose the resin to heaters or stoves, direct sunlight, ultraviolet rays, inert gas and oxidizing agents.
Before Using the Machine 5.2 Isopropyl Alcohol, IPA Please be cautious on the followings when handling the IPA. - Please make sure to wear nitril gloves all the time while using the IPA - Carefully follow the safety instructions provided with the isopropyl alcohol you purchase. You should consult the chemical manufacturer or supplier for more in depth safety information. - Isopropyl alcohol can be flammable, even explosive, and should be kept away from heat, fire or sparks.
Before Using the Machine 6. Instructions for Use Caution - The following items are for user-handling components made of metal, so they are very heavy. Resin tank Platform - If any of them falls while installing/removing or moving it, the machine may be damaged, or if it falls on a person, it may cause an injury. Caution - Do not operate the machine in a manner not specified in the instructions. - Do not remove any caution label or marking.
Before Using the Machine Important - If any of the following optical components positioned in the path of a LED beam reaching the resin is damaged or dirty, it may cause reduced quality or failed printing, so make sure to clean it while preparing the next one after completing the previous printing. Release film of the resin tank. LCD Protective glass. - For details on how to clean the resin tank, refer to “Resin Tank of 5. Maintenance”.
Before Using the Machine 7. Ventilation Caution - Use the machine in a place with good ventilation. Do not block vents. Inappropriate cooling may lead to high temperatures inside the machine. - In general, a new machine may produce small amount of gaseous components, so ensure good ventilation when the machine is used for the first time. If the machine is in operation for an extended time, do not stay in the same room for a long time.
Before Using the Machine 8. Notices ❖ Noise Emission Level The following noise level is measured in accordance of ISO 7779 and reported to meet ISO 9296. Some modes may not be available in products you purchased.
Before Using the Machine ③ CAUTION Any changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment. ④ This product has the certification issued under the authority of the FCC by one of Certification Body. FCC ID : 2AB83-A1SD ⑤ IC Compliance This Class [A] digital apparatus complies with Canadian ICES-003.
Before Using the Machine ❖ Condensation Dramatic change of the ambient temperature may produce water droplets on the interior and exterior of the machine. Wipe the water droplets on the outer surface, but for the inside please let them dry off by leaving front door and cover opened. Note - Do not remove caution labels or notations. If you can’t make them legible, or if caution label or notation is damaged, please contact your service representative.
Before Using the Machine 9. Disposal of Used Battery Control board uses a Lithium battery. Please discard used batteries following the environmentally friendly procedure stated on the manufacturer guidelines. To replace batteries, please contact a qualified service engineer.
Before Using the Machine 10. Wifi Module Disclaimer ❖ This machine includes a WIFI module compatible only with Sindoh’s 3D Printer models. Whether the WIFI module is equipped or not can be differed by models. Wifi Module Inside Important - This Wifi module can cause radio interference, therefore it should not be used for any purposes related to human lives. - Do not expose this product to water, humidity or liquid. - Do not expose this product to direct light, hot temperature or fire.
Before Using the Machine Important Frequency IEEE 802.11b : 2400 ~2483.5 MHz IEEE 802.11g : 2400 ~2483.5 MHz IEEE 802.11n(20MHz) : 2400 ~2483.5 MHz IEEE 802.11n(40MHz) : 2400 ~2483.5 MHz Antenna Power Density IEEE 802.11b : 16 dBm IEEE 802.11g : 15 dBm IEEE 802.11n(20MHz) : 14 dBm IEEE 802.11n(40MHz) : 14 dBm No. of Channels IEEE 802.11b : 14 IEEE 802.11g : 14 IEEE 802.11n(20MHz) : 14 IEEE 802.11n(40MHz) : 10 Modulation IEEE 802.11b : DQPSK, DBPSK, CCK IEEE 802.
Before Using the Machine 11. USB Flash Drive Disclaimer ❖ This USB flash drive is compatible with Sindoh’s 3D printer products. ❖ FCC COMPLIANCE STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Before Using the Machine ❖ IC Identification on Class of ITE CAN ICES-3 (B)/NMB-3 (B) DECLATION OF CONFORMITY Product name : USB Flash Drive Model name : 8GB-WJ004, 4GB-WJ004 FCC Rules : Tested to comply with FCC Part 15, Class B Operating Environment : For HOME OR OFFICE USE FCC COMPLIANCE STATEMENT This device complies with part 15 of the FCC Rules.
Sindoh A1SD Series USER MANUAL Preparation for Machine Operation 1
1 Preparation for Machine Operation 1. Specifications 1.1 Printing ※ Printing Method SLA (Stereo Lithography Apparatus) Max. Print Size (mm) W(max):110, D(max):80, H(max):180 Layer Thickness Setting 25㎛~100㎛ X-Y Resolution 50㎛ LED Wavelength 405nm LED Power 150W Resin Dental Model, Open Materials ※ Temperature Management Fan Heater Type Bed Leveling Manual We are exploring and developing a variety of resins in order to meet user needs.
1 Preparation for Machine Operation 2. Components 2.1 Basic Components Please check all basic components in the packaging box. Caution - Please keep the box and packaging material; they are needed for product exchange or repair service. 3D Printer Power Cord USB Cable USB Memory Quick Installation Guide T-Handle Hexagon Wrench (M5) Platform Leveling Gap Guide Spanner Platform Resin Tank Reference - The types of enclosed components may differ by the model.
1 2.2 Preparation for Machine Operation Finisher Kit Nipper Sprayer Nitril Gloves (2pairs) Washing Tub Cleaning Tray Filters (3pcs) Metal Scrapper Rubber Scrapper Funnel Hammer Empty Bottle Platform Cleaning Brush Kit List Warning - The blade side of metal scraper is very sharp. Please do not use it for other than removing the sculpture. In particular, do not touch or contact the blade side. - Keep rubber scraper clean after use.
Preparation for Machine Operation 3. 1 Understanding the parts [ Front ] [ Rear ] 4 8 7 6 3 2 1 5 11 9 10 10 No. 1 Part Name Description Power Button Press this button shortly to turn on printer. Press and hold for more than 2 seconds to turn off the printer.
1 Preparation for Machine Operation [ Interior ] 1 2 No. ※ Part Name Description 1 Resin Tank Working space where resin is filled and printing is processed. 2 Resin Tank Locking Levers Levers that lock and unlock the resin tank. May not be supported depending on model. [ Platform ] 4 3 2 1 No. 1-6 Part Name Description 1 Platform Workbench to which resin is cured by LED and print is attached. 2 Platform Handles Let users to hold when handling platform.
1 Preparation for Machine Operation 4. Installation (Incl. Connection and -S/W Installation) Caution - Please remove all packaging materials from inside and outside of the device. Furthermore, open the orange cover and remove all protective materials and accessories from interior. 4.1 Device Connection 1 Connect the power cable to the power socket on the rear side of the device, and connect the power cable to the power outlet. 2 Turn on the power switch on the back of the machine.
1 Preparation for Machine Operation 6 Please set the time zone of the machine according to instructions shown on UI. 7 Set time and date of the machine according to instructions shown on UI. 8 After booting up is completed, check if home screen is displayed on UI. 9 Open orange cover and install resin tank and platform. Install resin tank into the device as shown in the images below.
1 Preparation for Machine Operation Release two platform locking knobs from machine, attach the platform as shown below, tighten the locking knobs firmly, and attach the platform cover to the platform. 9 Connection to PC ① Direct Connection : Connects one end of the enclosed USB cable to the back of the device and the other end to the PC. ② Network Connection : Refer to “Network of 2.
1 Preparation for Machine Operation 4.2 S/W Installation 1 Start the S/W installation by clicking on “3DWOX Desktop.exe” file in the enclosed USB flash drive. 2 Install the additional files required by the software list. 3 When installation of the additional files is done, a pop-up window shows up as the picture below. Press [Next] button to start the installation of A Desktop Program.
Preparation for Machine Operation 4 Choose the destination location of the files and press [Next] to proceed. 5 All configurations get saved and the installation starts. 1 6 After all installation is complete, you can see that “A Desktop” icon created on the desktop of your computer.
Sindoh A1SD Series USER MANUAL UI Menu Function 2
2 1. UI Menu Function UI Menu Function Descriptions ※ Please refer to ‘Chapter 3. Printing’ for Print menu.
UI Menu Function 1.1 2 Home The first screen that user can see when turning ON the machine. 3 8 5 6 7 1 2 4 No. 1 Part Name Home Button Description Go to Home screen. ※ When it’s not Home screen, it changes to the Back( 2 Slide Menu Bar Open up Slide Menu. 3 Title Description on the screen you are currently working on. 4 Installed resin The specified installed resin is displayed. 5 Temperature Display the temperature inside the chamber.
2 1.2 UI Menu Function Installed Resin It is used to designate the resin currently installed on the machine. 1 Press [Resin icon] from the Home screen. 2 Select the resin currently installed on the machine. If the resin information on the slider does not match, an error is displayed.
UI Menu Function 1.
2 UI Menu Function XY Scale If the actual printing size differs from the designed model size, this function allows users to adjust the thickness error range and the horizontal(X)/ vertical(Y) scale of the print output. If you are not familiar with the machine, you can use the semi-auto calibration (adjustment) function, which suggests corrected (corrected / adjusted) values after measuring the print output size. 1 Press [Slide Menu Bar] from the Home screen.
UI Menu Function 2 4 XY scale(%) and XY thickness error(㎜) range reconfiguring screen appears.. X, Y(%) : Adjust the scale of model in X/Y axis. Xt, Yt(㎜) : You could modify the thickness(㎜) of outlines. 5 You can adjust and manage the printing scale for each resin separately. To select a resin type, press the [Resin Change] button and choose the resin type with the [<] or [>] button, then press the [Save] button. 6 Adjust each value with the slide bar or by pressing [+] or [-].
2 UI Menu Function 8 The semi-auto calibration is a function to see a suggested corrected value of the machine by printing out a pattern and measuring its dimensions. 9 Press [Print] to print out an embedded pattern. With the print output attached to the platform, measure X1, X2, Y1, and Y2 as shown in the picture. 10 Adjust each measured value with the slide bar on the screen or by pressing [+] or [-]. Measured values of X1 and Y1 can be entered, ranging from 66.5 mm to 73.
UI Menu Function 2 Z Offset This function allows users to adjust the distance between platform and resin tank to change the thickness of the first layer of raft. Change Z Offset value to [-] direction in case of printing failure caused by a drop of raft. On the other hand, change Z offset value to [+] value to increase raft thickness in case that raft is thicker than specified. 1 Press [Slide Menu Bar] from the Home screen. 2 Press [Setting] from the Menu screen. 3 Press [Z Offset].
2 UI Menu Function 4 Z Offset screen shows up. 5 Change a value by pressing [+] or [-] until it reaches the target number. Adjustable range is -0.05mm~+0.5mm in 0.05mm unit. Press [Save] when finished.
UI Menu Function 2 Chamber Heating This option allows the user to turn on/off the use of the heater. If the 3rd party resin that Sindoh does not supply is used, the print quality is not guaranteed by using the heater. Important - In the case of using Sindoh proprietary resin, you should keep the chamber temperature at the right level using the heater for the best printing quality. We recommend to set ON in this case. 1 Press [Slide Menu Bar] from the Home screen.
2 UI Menu Function 3 Press [Chamber Heating]. 4 It is a notice message notifying that the machine doesn’t guarantee the printing quality in Open Mode. If you agree on the message of pop-up window, press [Done] to continue. 5 Select [Off] or [On] for the Enable Chamber Heating. After selecting the Enable Chamber Heating [On], select [Off] or [On] of the Enable Pre Heating. Enable Pre Heating mode in [On], select temperature [25℃] or [High]. Click Save to save the settings.
UI Menu Function 2 Caution - If you select [On] to the Enable Pre Heating mode, the heater will always operate, so be careful about power consumption. - If you select [High] in the Enable Pre Heating mode, the chamber temperature increases. Please be careful of using for a long time may affect the resin’s performance. The First Exposure This function is used to change the strength at which the Raft is attached to the platform.
2 UI Menu Function 3 Press [1st Exposure]. The screen changing the exposure time according to the type of resin will appear. First, select the type of resin to change the exposure time . Then, press the [+] or [-] button to set the exposure time for the selected resin type. The adjustment can be incremented or decremented by 0.5 sec by pressing the active [+] or [-] button. When finishing adjustment, press [SAVE] to save the setting value.
UI Menu Function 2 2 Press [Setting] from the Menu screen. 3 Press [Platform Leveling]. 4 Remove all resin remaining in resin tank. Refer to “Resin tank of 5.Maintenance” for details of how to remove resin from the resin tank. Please note that leveling wil fail or won’t work precisely if resin still remaining in the resin tank.
2 UI Menu Function 5 Platform rises. Click [Next] when the Platform lifting completion message shows up. 6 Loosen six platform locking screws with a T-handle hexagon wrench, and press [Next]. Caution - Do not completely remove the screws from the platform and just loosen them up. If you try to remove the screws, they may drop onto the resin tank, and damage the release film and LCD protective glass.
UI Menu Function 2 7 The platform moves down. When the screen indicates that the lowering is complete, press [Next]. 8 When the platform lowering is complete, fasten back the six platform locking screws using a T-handle hexagon wrench, and press [Next] Lock the platform locking screws in the following order: ① front side → ② left side → ③ right side. ② Left side ① Front side ③ Right side Important - Make sure to lock the platform locking screws in the specified order.
2 UI Menu Function 9 Check the gap of the platform and the resin tank using enclosed gap gauge. The gap of all 4 corners as shown in instruction of UI needs to be checked. If gap gauge is inserted into any corners, it would mean platform is not leveled well. Press [Restart Platform Leveling] to perform the platform leveling process again. If gap checking is OK, press [Next]. 10 The platform moves up. When the screen indicates that the raising is complete, press [Next].
UI Menu Function 2 Cloud Monitoring This function lets users check the state of the machine remotely and send management data through email. 1 Press the [Slide Menu Bar] button from the home screen. 2 Press [Setting]. 3 Press [Cloud Monitoring].
2 UI Menu Function 4 Select [Off] or [On], and then press [Save] to save the settings. Level Printer This function lets users level the printer. Important - Sensor which is used to display the level or the printer should be used within the proper tempearature(20~30 ℃) in order to prevent malfunction. Please run the level printer process after checking if ambient temperature is proper. 1 Press the [Slide Menu Bar] button from the home screen. 2 Press [Setting].
UI Menu Function 2 3 Swipe up the screen, and then select [Level Printer]. 4 The screen shows the leveling state of the printer. The leveling state screen shows the level of the machine with a circular level, which is commonly found in a washing machine. The circular level shows the level state with a bubble. Level the printer so that the orange circle of level is centered.
2 UI Menu Function 5 With the enclosed spinner, properly turn the leveling screws located at the bottom of the printer to level the machine. Turn the leveling screws counterclockwise to lower the printer. Turn the leveling screws clockwise to raise the printer.
UI Menu Function 2 Level it so that the bubble is centered in the level and turns green. Once the bubble turns green, the [Done] button will be activated so that the leveling procedure can be completed. Caution - If the leveling screws are turned clockwise too much, they may be removed from the printer. To prevent this, turn them counterclockwise to lower any higher corner. - Make sure that the four leveling screws touch the ground.
2 UI Menu Function Network This function let users to set up network configurations of the device. Both wired and wireless LAN can be configured in details. Important - Using both wired and wireless network simultaneously is not recommended for electric devices which can be connected to network. Due to characteristics of network communication, data may not be processed properly when data is coming in via both wired and wireless network. 1 Press [Slide Menu Bar] from the Home screen.
UI Menu Function 2 3 Swipe the screen upward, and press [Network]. 4 Network setup screen shows up. Enable to choose wireless or wired connection according to your network connection provider. Wireless (Wifi) Setting 1 2 3 4 No. Part Name Description 1 ON/OFF Turn ON or OFF Wifi. 2 Network Name (SSID) Select SSID or enter the name manually if can’t find the one you’re looking for. 3 DHCP Allocate IP address automatically.
2 UI Menu Function 5 As pressing [Network] button, list of SSIDs is displayed. Select a SSID you want to connect, and press [Save] to store the setting. If selected SSID requires password, enter it. Select DHCP if the SSID gets IP automatically assigned from the network provider. As press [Connect], it will connect to the internet with the SSID. If connecting successfully, the assigned IP will be shown.
UI Menu Function Press [Static] in the network setting screen if a fixed IP address is required. Press the pen icon [ on the right to enter the IP address manually. Then, press [Connect] to connect to an SSID. 2 ] Wired LAN Setting For wired LAN, DHCP and fixed IP settings can be selected to connect to the network in the same procedure as the Wi-Fi. 1 2 3 No. Name Description 1 DHCP Select it to allocate IP addresses automatically. 2 Static Select it to allocate fixed IPs.
2 UI Menu Function Test Print This function allows users to print a sample model already saved in the internal memory of printer. 1 Press [Slide Menu Bar] from the Home screen. 2 Press [Setting] from the Menu screen. 3 Swipe up the screen, and then select [Test Print].
UI Menu Function 2 4 The example files of the machine are listed. Select a file to print. ] button to preview the information of the file to print. 5 Press the [ The information of the selected file is displayed. 6 Press the [ ] button of the file to print to start printing.
