3323 Instruction Manual Manual de Instrucciones Manuel d'Instruction
EN IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic safety should always be followed, including the following: Read all instructions before using this sewing machine. DANGER - To reduce the risk of electric shock: 1. An appliance should never be left unattended when plugged in. 2. Always unplug this appliance from the electric outlet immediately after using and before cleaning. 3. Always unplug before re-lamping.
E IMPORTANTES INSTRUCCIONES DE SEGURIDAD Cuando se utiliza un dispositivo eléctrico, debe seguirse siempre precauciones de seguridad básica, incluyendo las siguientes: Leer todas las instrucciones antes de utilizar está máquina de coser. PELIGRO - Para reducir el riesgo de sacudidas eléctricas: 1. Un dispositivo eléctrico nunca debe dejarse desatendido cuando está conectado. 2. Desenchufar siempre la máquina de la toma de corriente inmediatamente despues de utilizarla y antes de su limpieza. 3.
F INSTRUCTIONS IMPORTANTES DE SÉCURITÉ Lors de l'utilisation d'un appareil électrique, il est important de toujours suivre certaines précautions de sécurité dont certaines sont les suivantes : Lire toutes les instructions avant d'utiliser votre machine à coudre : 7. 8. 9. DANGER - Pour éviter tout risque d'électrocution : 1. 2. 3. Lorsque la machine est branchée, ne jamais la laisser sans surveillance.
EN Congratulations As the owner of a new Singer sewing machine, you are about to begin an exciting adventure in creativity. From the moment you first use your machine, you will know you are sewing on one of the easiest to use sewing machines ever made. May we recommend that, before you start to use your sewing machine, you discover the many features and the ease of operation by going through this instruction book, step by step, seated at your machine.
EN List of contents Machine Basics Principle Parts of the Machine..............................................................................................................................................2/4 Connecting Machine to Power Source ....................................................................................................................................6 Two Step Presser Foot Lifter .......................................................................................................
E Indice Partes de la máquina Partes de la máquina ...........................................................................................................................................................3/5 Conexión de la máquina a la fuente de alimentación eléctrica ...............................................................................................7 Elevador del prensatelas de dos tiempos ........................................................................................................
F Table des matières L'essentiel de la machine Les composantes principales de la machine à coudre .........................................................................................................3/5 Branchement de la machine à une source d'alimentation.......................................................................................................7 Levier du pied presseur à deux niveaux.............................................................................................................
EN Principal Parts of the Machine 1. Thread tension dial 2. Thread take-up lever 3. Reverse sewing lever 8 1 4. Thread cutter 9 5. Presser foot 2 6. Needle plate cover 7. Removable extension table/ accessory storage 3 8. Bobbin stopper 4 10 11 9. Stitch width dial 10. Stitch length dial 5 6 11. Pattern selector dial 12. Automatic threader 7 13.
E Partes de la máquina F Les composantes principales de la machine à coudre 1. Disco de tensión 2. Tirahilos 1. Réglage de la tension 3. Palanca para coser hacia átras 2. Releveur du fil 4. Cortahilos 3. Levier de couture arrière 5. Prensatelas 4. Coupe fil 6. Placa de cubierta de canilla 5. Pied presseur 7. Mesa de coser convertible/ caja de accesorios 6. Couvercle de la canette 8. Tope del devanador 7. Bras amovible / rangement des accessoires 9. Disco selector de ancho de puntada 8.
EN Principal Parts of the Machine 14. Horizontal spool pin 15. Bobbin winding spindle 16. Hole for auxiliary spool pin 20 17. Handwheel 21 18. Power and light switch 14 19. Main plug socket 15 20. Bobbin thread guide 16 21. Upper thread guide 22. Face plate 17 23. Handle 22 23 24 24. Presser foot lifter 25. Foot speed control 26.
E Partes de la máquina F Les composantes principales de la machine à coudre 14. Portacarrete 15. Devanador 14. Porte bobine horizontal 16. Orificio para el portacarrete adicional 15. Axe du bobineur 17. Volante 16. Trou pour insérer un deuxième axe de bobine 18. Interruptor de encendido y apagado 17. Volant 19. Enchufe de conexión a la red 18. Interrupteur d'alimentation et d'éclairage 20. Guía del devanador 19. Prise de branchement du fil d'alimentation 21. Guía del hilo superior 20.
EN Connecting Machine to Power Source Connect the machine to a power source as illustrated. (1) This appliance is equipped with a polarized plug which must be used with the appropriate polarized outlet. (2) Attention: Unplug power cord when machine is not in use. A Foot control The foot control pedal regulates the sewing speed. (3) Attention: Consult a qualified electrician if in doubt of how to connect machine to power source. Unplug power cord when machine is not in use.
E Conexión de la máquina a la fuente de F Branchement de la machine à une source Conecte la máquina a una fuente de alimentación según se ilustra. (1) Esta máquina está provista de un conector polarizado, que debe utilizarse con una toma de corriente polarizada adecuada. (2) Brancher la machine comme indiqué ci-contre. (1) La fiche de la machine est dotée de broches normalisées et doit être utilisée avec une prise de courant conforme aux normes en vigueur.
EN Two Step Presser Foot Lifter When sewing several layers or thick fabrics, the presser foot can be raised to a higher position for easy positioning of the work. (A) E Elevador del prensatelas de dos tiempos Cuando se cose varias capas de tela gruesa, el prensatelas puede elevarse a una posición alta para facilitar la colocación de la tela (A).
EN Accessories 1 Standard accessories (1) a. All purpose foot b. Zipper foot c. Buttonhole foot d. Button sewing foot e. Gathering foot f. Darning/ embroidery foot g. Even Feed foot h. Side cutter i. Seam ripper/ brush j. Edge/ quilting guide k. Pack of needles l. Spool holders m. Bobbin (3x) n. L-screwdriver o. Darning plate p. Auxiliary Spool Pin q. Spool pin felt r.
E Accesorios F Accessoires Accesorios incluidos (1) a. Prensatelas universal b. Prensatelas para cremalleras c. Prensatelas para ojales d. Prensatelas para coser botones e. Prensatelas para plisar f. Prensatelas de zurcido y bordado libre g. Prensatelas de avance simultáneo h. Recortalados i. Brocha descosedor j. Guía para coser bordes/ edredones k. Paquete de agujas l. Portacarrete m. Bobinas (3x) n. Destornillador plano o. Plancha de zurcido p. Portacarrete Auxiliar q.
EN Winding the Bobbin - Place thread and corresponding spool holder on to spool pin. (1/2) - Snap thread into thread guide. (3) - Wind thread clockwise around bobbin winder tension discs. (4) - Thread bobbin as illustrated and place on spindle. (5) - Push bobbin spindle to right. (6) - Hold thread end. (7) 1 - Step on foot control pedal. (8) - Cut thread. (9) 3 2 - Push bobbin spindle to left (10) and remove.
E Devanado de la bobina F Remplissage de la canette - Coloque el hilo y sujete con la tapa grande o pequeña el poste. (1/2) - Placer le fil et le support correspondant sur le porte bobine. (1/2) - Deslice el hilo del carrete a través de la guía del hilo superior. (3) - Glisser le fil dans le guide. (3) - Enrouler le fil dans le sens horaire autour des disques de tension de l'enrouleur de canette.
EN Inserting the Bobbin When inserting or removing the bobbin, the needle must be fully raised. 1. Insert the bobbin in the bobbin case with the thread running counterclockwise direction (arrow). 2. Pull the thread through the slit (A). 3. Draw the thread clockwise until it slips into the notch (B). 4. Pull out about 15 cm (6 inches) of thread and attach the bobbin cover plate. (C) A Attention: Turn power switch to off ("O") before inserting or removing the bobbin.
F Insertion de la canette E Colocación de la bobina Cuando se inserte o retire la canilla, la aguja debe estar completamente elevada. Lorsque vous insérez ou retirez une canette, assurezvous que l'aiguille est complètement relevée. 1. Inserte la canilla en su cápsula con el hilo girando a la izquierda (sentido de la flecha). 1. Insérer la canette dans son logement, le fil étant orienté dans le sens anti-horaire (flèche). 2. Pase el hilo a través de la hendidura (A). 2.
EN Threading the Upper Thread This is a simple operation but it is important to carry out correctly as by not doing so several sewing problems could result. - Start by raising the needle to its highest point (1), and continue turning the handwheel counterclockwise until the needle just slightly begins to descend. Raise the presser foot to release the tension discs. Note: For safety, it is strongly suggested you turn off the power before threading. - Lift up the spool pin.
E Enhebrado del hilo superior F Enfilage supérieur Se trata de una operación sencilla pero es importante realizarla correctamente pues de no hacerlo podría surgir varios problemas en la costura. Cette opération est simple. Il est important de l'exécuter correctement sous peine de faire éventuellement face à plusieurs problèmes de couture. - Comience elevando la aguja a su posición más alta (1) y también eleve el prensatelas para liberar los discos de tensión.
EN Automatic Needle Threader - Raise the needle to its highest position. - Press lever (A) down as far as it will go. - The threader automatically swings to the threading position (B). A - Pass thread around thread guide (C). - Pass the thread in front of the needle around the hook (D) from bottom to top. B C - Release lever (A). - Pull the thread through the needle eye.
E Ensartador automático de la aguja F Enfileur automatique d'aiguille - Eleve la aguja a su posición más alta. - Relever l'aiguille à sa position la plus haute. - Presione la palanca (A) hacia abajo lo más posible en su recorrido. - Abaisser le levier (A) le plus possible. - L'enfileur se met automatiquement en position d'enfilage (B). - El ensartador oscila automáticamente a la posición de enhebrado. (B) - Faire passer le fil autour du guide-fil (C).
EN Raising the Bobbin Thread Hold the upper thread with the left hand. Turn the handwheel (1) towards you (counterclockwise) lowering, then raising needle. Note: If it is difficult to raise the bobbin thread, check to make sure the thread is not trapped by the hinged cover or the Removable Extension Table. 1 Gently pull on the upper thread to bring the bobbin thread up through the needle plate hole. (2) Lay both threads to the back under the presser foot.
F Pour remonter le fil de canette E Elevación del hilo de la bobina Sujete el hilo superior con la mano izquierda. Gire el volante (1) hacia usted hasta que baje totalmente la aguja, siga girando hasta volver a subir la aguja. Tenir le fil supérieur avec la main gauche. Tourner le volant (1) vers vous (sens anti-horaire) pour abaisser et lever l'aiguille.
EN Thread Tension Upper thread tension Basic thread tension setting: "4". (1) To increase the tension, turn the dial to the next number up. To reduce the tension, turn the dial to the next number down. A. Normal thread tension for straight stitch sewing. B. Thread tension too loose for straight stitch sewing. Turn dial to higher number. C. Thread tension too tight for straight stitch sewing. Turn dial to lower number. D. Normal thread tension for zig zag and decorative sewing.
F Tension du fil E Tensión del hilo Tension du fil supérieur Réglage de base pour la tension du fil: "4". (1) Pour augmenter la tension, tourner le cadran de réglage de la tension vers une valeur plus élevée. Pour réduire la tension, tourner le cadran de réglage de la tension vers une valeur inférieure. A. Tension du fil correcte pour une couture à point droit. B. La tension du fil est trop faible pour une couture à point droit. Tourner le cadran de réglage de la tension vers une valeur plus élevée. C.
EN How to Choose Your Pattern The diagram on this page display the stitch patterns available on the machine. a b c Stitches in the top of the diagram are indicated on the Pattern Selector Dial in gray. To select the patterns indicated with the gray color, turn the Pattern Selector Dial. (d) Use the Stitch Length Dial (c) to adjust the stitch length as desired for the project. Use the Stitch Width Dial (b) to adjust the width of the stitch as desired.
F Comment choisir votre motif E Cómo seleccionar su puntada El diagrama en esta página muestra los diseños de las puntadas disponibles en la máquina. Le diagramme sur la page précédente présente les motifs de point disponibles sur la machine. Las puntadas en la parte superior del diagrama están señaladas con gris en el Selector de Puntada. Para elegir los patrones indicados en color gris gire el selector de puntada.
EN Stitch Width Dial & Stitch Length Dial Function of stitch width dial The maximum zigzag stitch width for zigzag stitching is 6mm; however, the width can be reduced on any patterns. The width increases as you move zigzag dial from "0" - "6". (1) The Stitch Width Dial is also the control for the straight stitch infinite needle position. "0" is center needle position, "6" is full left. Function of stitch length dial while zig-zag stitching Set the Pattern Selector Dial to zig-zag.
E Selector de ancho de puntada y F Cadran de largeur de point et cadran de Selector de largo de puntada longueur de point Fonction du cadran de largeur de point La largeur maximum de point zigzag pour la couture en zigzag est 6mm ; toutefois, la largeur peut être réduite sur n'importe quel motif. La largeur augmente au fur et à mesure que vous déplacez le cadran de zigzag de "0" à "6". (1) Le cadran de largeur de point contrôle également la position d'aiguille infini au point droit.
EN Sewing Straight Stitch To begin sewing, set the machine for straight stitch. (1) Place the fabric under the presser foot with the fabric edge lined up with the desired seam guide line on the needle plate. (2) Lower the presser foot lifter, and then step on the foot controller to start sewing.
F Couture au points droits E Puntada recta Para comenzar a coser, gire el selector de puntadas en la puntada recta, puede seleccionar la posición de la aguja en centro o a la derecha. (1) Pour commencer à coudre, régler la machine sur le point droit. (1) Placer le tissu sous le pied presseur avec le bord du tissu aligné au guide de couture souhaité sur la plaque à aiguilles. (2) Coloque la tela bajo prensatelas con el borde de la tela alineado con la línea de guía deseada de la costura en la placa aguja.
EN Reverse Sewing To secure the beginning and the end of a seam, press down the reverse sewing lever (A). Sew a few reverse stitches. Release the lever and the machine will sew forward again. (1) A Removing the Work Turn the handwheel toward you (counterclockwise) to bring the thread take up lever to its highest position, raise the presser foot and remove work behind the needle and presser foot. (2) 1 2 B Cutting the Thread Pull the threads under and behind the presser foot.
E Remate F Couture en marche arrière Para fijar el comienzo y el final de la costura, presione la palanca de retroceso. Haga unas pocas puntadas hacia atrás. Suelte la palanca y la máquina coserá de nuevo hacia delante (A). (1) Afin de renforcer le début et la fin d'une couture, abaisser le bouton marche arrière. Faire quelques points en marche arrière. Lâcher le bouton et la machine reprendra la couture vers l'avant (A).
EN Choosing Stretch Stitch Patterns The Stretch Stitch Patterns are indicated with a blue color on the Pattern Selector Dial. To select these stitches, turn the Pattern Selector Dial to the desired pattern. Then, turn the Stitch Length Dial to the indicator marked "S1". Though there are several stretch patterns, here are two examples: Straight Stretch Stitch (1) Set the Pattern Selector Dial to " ". Used to add triple reinforcement to stretch and hardwearing seams.
E Selección de Puntadas elásticas F Choisir les motifs de point extensible Les motifs de point extensible sont indiqués en bleu sur le cadran de sélection de motifs. Pour sélectionner ces points, tourner le cadran de sélection de motifs sur le motif souhaité. Puis, tourner le cadran de longueur de point sur l'indicateur marqué par "S1".
EN Blind Hem For hems on curtains, trousers, skirts, etc. Blind hem for stretch fabrics. Blind hem for firm fabrics. Set the Stitch Length Dial with the range shown on the diagram at the right. Blind hems, however, are normally sewn with a longer stitch length setting. Set the Stitch Width Dial at a setting appropriate for the weight/type of fabric being sewn, within the range shown in the diagram on the right of the page.
E Dobladillo Invisible F Ourlet invisible Pour les ourlets sur les rideaux, pantalons, jupes, etc. Para dobladillos, cortinas, pantalones, faldas, etc. Ourlet invisible pour tissus extensibles. Para realizar un dobladillo invisible en telas elásticas, seleccione esta puntada. Ourlet invisible pour tissus solides. Régler le cadran de longueur de point dans la gamme tel qu'indiquée sur le diagramme à droite.
EN Sew 1-Step Buttonhole Buttonhole sewing is a simple process that provides reliable results. However, it is strongly suggested to always make a practice buttonhole on a sample of your fabric and stabilizer. Making a Buttonhole 1. Using tailor's chalk, mark the position of the buttonhole on the fabric. 2. Attach the buttonhole foot and set the Pattern Selector Dial to " ". Set stitch length dial to " ". Set the stitch width at "6". The width however may need to be adjusted according to the project.
E Ojal de un sólo paso F Couture de boutonnières en 1 étape Confeccionar ojales es un proceso sencillo que proporciona resultados fiables. Sin embargo, se recomienda realizar siempre un ojal de práctica en una muestra de tela e intercalar. La couture de boutonnière est un processus simple qui assure des résultats fiables. Toutefois, il est fortement suggéré de toujours réaliser une boutonnière d'essai sur un échantillon de tissu et d'entoilage. Confección de un ojal 1.
EN Sewing on Buttons Install the darning plate. (1) Change the all purpose foot to the button sewing foot. (2) Set the stitch length to "0". Place the button and fabric under the Button Sewing foot, as illustrated in (3). Set the machine for zig-zag stitch, then set the width to number "3" - "6". Turn the handwheel to check that the needle goes cleanly into the left and right holes of the button. Adjust the stitch width, as needed, according to the distance between the holes of the button.
E Pegado de botones F Couture de boutons Poser la plaque de reprisage. (1) Changer le pied presseur multi-usage pour le pied de couture de bouton. (2) Régler la longueur de point sur "0". Coloque la placa cubre impelentes (1). Cambie el prensatelas especial para coser botones.(2) Ajuste el largo de puntada en "0". Coloque el botón y tela debajo del Pie de Prensatelas para Botón, como se muestra en (3). Coloque el selector de puntadas en la puntada de Zigzag, y ajuste el ancho de puntada entre "3" y "6".
EN Gathering - Remove the presser foot shank. (1) - Attach the gathering foot. - Sew a single row or multiple rows of straight stitches. - If more gathering is required, loosen the upper thread tension to below 2 so that the lower thread lies on the under side of the material. Setting stitch length to a longer setting will help produce more gathers as well. - Pull the lower thread to gather more of the material.
E Prensatelas para plisar F Pied pour plissage - Retire la abrazadera del prensatelas. (1) - Retirer le pied presseur et l'attache. (1) - Ponga el prensatelas para plisar. - Fixer le pied pour plissage. - Cosa una o varias hileras de puntadas rectas. - Coudre une rangée simple ou des rangées multiples de points droits. - Si se requiere más fruncido, afloje la tensión del hilo superior por debajo de 2, de modo que el hilo inferior quede por debajo de la tela.
EN Free Motion Darning, Stippling Darning: Install the darning plate. (1) Remove the presser foot shank. (2) Attach the darning/ embroidery foot to the presser foot bar. The lever (a) should be behind the needle clamp screw (b). Press the darning/ embroidery foot on firmly from behind with your index finger and tighten the screw (c). (3) For darning, first sew around the edge of the hole (to secure the threads). (4) First row: Always work from left to right. Turn work by 90° and sew over previous stitching.
E Zurcido de brazo libre F Reprisage et matelassage pointillé Instale la placa de zurcir. (1) Placer la plaque de reprisage sur la plaque aiguille. (1) Retire la abrazadera del prensatelas. (2) Fije el prensatelas de zurcir en la barra prensatelas. La palanca (a) debe estar detrás del tornillo de sujeción de la aguja (b). Presione el prensatelas zurcidor con firmeza, desde detrás con el dedo índice y apriete el tornillo (c).
EN The Even Feed Foot Accessory Always try to sew first without the Even Feed Foot accessory which should be used only when necessary. e It is easier to guide the fabric and you have a better view of the seam when using the standard, regular foot on your machine. Your sewing machine offers excellent stitch quality on a wide range of fabrics from delicate chiffons to multiple layers of denim.
E Prensatelas de avance simultáneo F Pied double entraînement Siempre trate de coser primero una muestra antes de coser la prenda final. Toujours tenter de coudre d'abord sans utiliser le pied double entraînement qui doit être employé uniquement si nécessaire. Será más fácil guiar la tela y tendrá una mejor visión de su costura cuando esta cosiendo use el prensatelas normal estándar de su máquina.
EN Side Cutter Lift the presser foot lifter (a) to raise the presser foot bar. (1) Remove the presser foot. (See page 49) b Attach the Side Cutter to the machine as follows (2): - Insert the arm (b) to the needle clamp (c). - Lower the presser foot lifter while making sure the pin (d) of the side cutter fits the presser shank (e) and is secured in place. a c e d Cut an edge of fabric about 2~3 cm. (3) Put fabric on guide plate (f) and push left side of the fabric to go below presser foot (g).
E Cortador lateral F Pied de surjet coupeur Suba la palanca del pie prensatelas (a) para levantar el zanco del pie de prensatelas. (1) Relever la barre du pied presseur (a) pour faire monter l'attache du pied presseur (1) Retire el pie de prensatelas (ver página 49). Retirer le pied presseur (voir page 49).
EN Installing the Removable Extension Table Hold the removable extension table horizontally, and push it in the direction of the arrow. (1) To remove the extension table, pull it toward the left. 1 The inside of the removable extension table can be utilized as an accessory box. To open, flip cover down as shown.
E Instalación de la cubierta removible F Installation du bras amovible Coloque la máquina en una superficie estable, empuje la cubierta removible como indica la flecha, y luego jale hacia afuera. (1) Maintenir le bras amovible en position horizontal et le pousser comme indiqué ci-contre. (1) Pour enlever le bras amovible le tirer vers la gauche. El interior de la cubierta removible, se puede utilizar para guardar los accesorios de la máquina.
EN Attaching the Presser Foot Shank Raise the presser foot bar (a) with the presser foot lifter. Attach the presser foot shank (b) as illustrated. (1) a a Attaching the presser foot Lower the presser foot shank (b) using the presser foot lifter, until the cut-out (c) is directly above the pin (d). (2) The presser foot (f) will engage automatically. e c b Removing the presser foot Raise the presser foot using the presser foot lifter. (3) Raise the lever (e) and the foot disengages.
E Colocación del portaprensatelas F Installer le support du pied presseur Eleve la barra del prensatelas (a). Coloque el portaprensatelas (b) según se ilustra (1). Relever la barre du pied (a) avec le releveur de pied presseur. Attacher le support du pied presseur (b) comme illustré. (1) Colocación del prensatelas Baje el portaprensatelas (b) hasta que el corte (c) esté directamente encima del perno (d).
EN Needle/ Fabric/ Thread Chart NEEDLE, FABRIC, THREAD SELECTION GUIDE NEEDLE SIZE FABRICS 9-11 (70-80) Lightweight fabrics-thin cottons, voile, silk, muslin, interlocks, cotton knits, tricots, jerseys, crepes, woven polyester, shirt & blouse fabrics. 11-14 (80-90) 14 (90) 16 (100) 18 (110) Medium weight fabrics-cotton, satin, kettlecloth, sailcloth, double knits, lightweight woolens. Medium weight fabrics-cotton duck, woolen, heavier knits, terrycloth, denims.
E Guía de selección de agujas/ telas/ hilos GUÍA DE SELECCIÓN DE AGUJAS/ TELAS/ HILOS CALIBRE DE LA AGUJA TELA HILO 9-11 (70-80) Telas de poco peso - algodones delgados, Voile, sarga, seda, muselina, interlocks (puntadas entrelazadas), tejidos de algodón, tricots, jerseys, crepés, poliester tejido, telas para camisas y blusas. Hilo ligeros en algodón, nylon, poliester o poliester bordado. 11-14 (80-90) Telas de peso medio, raso, lona, tela de velas, géneros de punto doble, tejidos de lana.
F Table de correspondance de l'aiguille, du tissu et du fil GUIDE DE SÉLECTION DE L'AIGUILLE, DU TISSU ET DU FIL DIMENSIONS DE L'AIGUILLE TISSUS FIL 9-11 (70-80) Tissus légers, cotons légers, voile, serge, soie, mousseline, Qiana, tissu interlock, tricots de coton, tricots, jerseys, crêpes, polyester tissé, tissus pour chemises et blouses. File de coton léger, nylon, polyester ou de coton enrobé de polyester.
EN Darning Plate For certain types of work, (e.g. darning or free-hand embroidery), the darning plate must be used. Install the darning plate as illustrated. For normal sewing, remove the darning plate.
E Placa cubre impelentes F Plaque à repriser Para ciertos trabajos, como por ejemplo para zurcir o para bordar a mano libre, etc. se debe colocar la placa cubre impelentes. Pour certains types de travaux, (par ex. reprisage ou broderie à main levée), la plaque à repriser doit être utilisée. Installer la plaque à repriser comme illustré. Instalar la placa cubre impelentes según la ilustración. Pour la couture normale, retirer la plaque à repriser.
EN Inserting & Changing Needles Change the needle regularly, especially if it is showing signs of wear and causing problems. For best sewing results ® always use SINGER Brand Needles. D A Insert the needle as illustrated as follows: A. Loosen the needle clamp screw and tighten again after inserting the new needle. (1) B. The flat side of the shaft should be towards the back. C/D.Insert the needle as far up as it will go.
E Colocación y cambio de agujas F Insertion et changement d'aiguille Cambie la aguja preiódicamente, sobre todo si muestra signos de desgaste y origina problemas. Para mejores resultados de la costura, utilice siempre agujas originales de ® SINGER . Remplacer l'aiguille régulièrement, plus particulièrement si elle indique des signes d'usure et cause des problèmes. Pour obtenir les meilleurs résultats, toujours utiliser des aiguilles ® fabriquées par SINGER .
EN Changing the Bulb Disconnect the machine from the power supply by removing the plug from the main socket! Replace bulb with same type rated 10 watts (110-120V area) or 15 watts (220-240V area). - Loosen screw (A) as illustrated. (1) Remove the face plate (B). Unscrew the bulb and install a new one (C). (2) Replace the face plate and tighten screw. B A Should there be any problem, consult your authorized ® SINGER retailer.
E Cambio de la bombilla F Changement de l'ampoule Desconecte la máquina de la alimentación principal retirando el conector desde la toma de corriente. Sustituir la bombilla con otra del mismo tipo de 10 voltios (tensión de 110-120V área) o 15 voltios (tensión de 220-240V área). Débrancher la machine de l'alimentation électrique en retirant la prise! Remplacer l'ampoule par une ampoule du même type de 10 Watts (pour 110-120V) ou 15 watts (pour 220-240V). - - Afloje el tornillo (A) según se ilustra.
EN Troubleshooting Guide Problem Cause Correction Upper thread breaks 1. 2. 3. 4. 5. 6. 1. 2. 3. 4. 5. 6. Lower thread breaks 1. The bobbin case is not inserted correctly. 2. The bobbin case is threaded wrong. 3. The lower thread tension is too tight. 1. Remove and reinsert the bobbin case and pull on the thread. The thread should pull easily. 2. Check both bobbin and bobbin case. 3. Loosen lower thread tension as described. Skipped stitches 1. 2. 3. 4. The needle is not inserted correctly.
E Problemas y soluciones Problema Causa Solución El hilo superior se rompe 1. 2. 3. 4. 5. 6. La máquina está mal enhebrada. La tensión del hilo es demasiado fuerte. El hilo es demasiado grueso para la aguja. La aguja no está colocada correctamente. El hilo se ha enredado en la caja bobina. La aguja está torcida o despuntada. 1. 2. 3. 4. 5. 6. Enhebrar la máquina correctamente. Disminuir la tensión del hilo superior. (número menor) Usar una aguja más gruesa. Colocar la aguja correctamente.
F Guide de dépannage Problème Cause Solution Le fil supérieur casse 1. La machine n'est pas correctement enfilée. 2. La tension du fil est trop élevée. 3. Le fil est trop gros pour l'aiguille. 4. L'aiguille n'est pas bien insérée. 5. Le fil est enroulé autour du porte bobine. 6. L'aiguille est endommagée. 1. Réenfiler la machine. 2. Réduire la tension. (valeur inférieure) 3. Choisir une aiguille plus grosse. 4. La retirer et la réinsérer. (côté plat vers l'arrière) 5.
021Q5A0101( ) Mar/10 SINGER 3323S(Q50A)