ER10 Instruction Manual 34074 Singer ER10 Manual.
This household sewing machine is designed to comply with IEC/EN 60335-2-28 and UL1594 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic safety precautions should always be followed, including the following: Read all instructions before using this household sewing machine. DANGER - To reduce the risk of electric shock: • A sewing machine should never be left unattended when plugged in.
, r e Table of Contents .......................................... 3 Overview of the machine ............................. 3 Accessories ...................................................... 4 Setting Up........................................................ 4 Attaching the power cord and foot control4 Machine speed ............................................... 4 For the USA and Canada .............................. 4 Cloth Presser ...................................................
Accessories 1. 2. 3. 4. 5. 6. Screwdriver 1,5 mm Allen wrench Needles Cleaning brush Machine cover Instruction book Setting Up Attaching the power cord and foot control Plug the power cord into machine socket, then into a wall outlet. Always make sure the power is OFF and remove the plug from the wall outlet when the machine is not in use, or when making any adjustments such as changing needles or light bulb. Note: Before plugging in, check to ensure that the foot control is of type “4C-337G” or “C-9000”.
Cloth Presser English The cloth presser is to prevent cloth/fabric/ materials from lifting during the felting process. 1. Place the cloth/fabric/materials on the needle plate and under the cloth presser. 2. Loosen the cloth presser height adjusting screw to adjust the height of the cloth presser. 3. Move the clear fabric cover with needle guard up or down until the red indicator on the presser bar aligns with the correct height for the thickness of your fabric and felting material.
Getting Started Let your creativity soar with this needle felting machine! Now you can make your projects even more creative. Let your imagination soar to create beautiful felted embellishment on your garments, arts and crafts, home decorating, quilting, sewing, scrap booking and much more. Fabric and trims that can be used Just about any fabric can be felted with the needle felting machine, however, some fabrics tend to have more favorable results when embellishing or laundering afterward.
Start Embellishing English Layer the project fabric with the material that will be felted together to create the embellishment. Make sure that the smaller piece to be felted is on the correct side of the project (right or wrong side). The embellishing fabric can be put on either the right or the wrong side of the project. Experiment rst on scraps to see which look you like best for your project. Place the layers to be felted together under the clear fabric cover with needle guard.
Flat Bed Extension / Free Arm Remove the at bed extension by sliding it to the left and the machine will convert to a free arm. This will allow you to embellish sleeves, pant legs, and small areas that are sewn in the round. This will also give you access to the free arm door to clean out the lint that has accumulated from felting. Accessory Storage Open the accessory storage compartment by pulling the drawer forward. 8 34074 Singer ER10 Manual.
Maintenance English Changing the needle(s) Use #S1037 needles for the needle felting machine. Do not use any other type of needles. Note: #S1037 needle is a very special needle and is exclusive for the needle felting machine. Purchase these needles at the same authorized dealer where you purchased your machine. When you change needle(s), unplug the power cord from the wall outlet. 1. Turn the handwheel until the needle bar is at the highest position. 2.
6. When replacing the needle clamp, make sure the needle bar is in its highest position. Insert the needle clamp into the needlebar, rotate and lightly push upward till the pin seats into the needle bar. Tighten the needle clamp screw clockwise with 1.5mm Allen wrench. Note: Replace the clear fabric cover with needle guard and presser height adjusting screw before continuing to use the machine.
Trouble Shooting Needle bent or Needle breakage English 1. Are you moving the materials too quickly? 2. Are the needles touching the cloth presser or needle plate? 3. Is there dust or lint around the edge of the needles, cloth presser,or in the holes of the needle plate? 4. Does the lint box area need to be cleaned? For problems other than bent needles or needle breakage, please contact your retailer.
Singer Sewing Company 1224 Heil Quaker Blvd., LaVergne 37086 34074 Singer ER10 Manual.
