FABRIC STEAM PRESS INSTRUCTION MANUAL R TABLE OF CONTENTS Important Safety Instructions....................1-3 Getting to Know Your Steam Press .... .......4-5 Features of the Steam Press.........................6 Operation&Instructions................................7 Tips Pressing............................................8-11 Cleaning the Steam Press.............. .............12 Storage................................... ....................12 Troubleshooting..........................................
IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances, especially when children are present, basic safety precautions should always be taken, including the following: READ ALL INSTRUCTIONS BEFORE USING KEEP AWAY FROM WATER DANGER-Any appliance is electrically live even when the switch is off. To reduce the risk of death by electric shock: 1.Always unplug it immediately after using. 2.Do not place or store appliance where it can fall or be pulled into a tub or sink. 3.
operateINSTRUCTIONS this appliance if it has a damaged cord or plug, if it is not working properly, or IMPORTANT4.Never SAFETY 5.Children should be supervised to ensure that they do not play with the appliance. 6.Never operate this appliance if it has a damaged cord or plug, if it is not working properly, or if it has been dropped or damaged, or dropped into water. Do not attempt to repair the appliance.
IMPORTANT SAFETY INSTRUCTIONS or if it is used incorrectly. To reduce the risk of contact with hot water as it escapes through steam vents, test appliance before each use by holding and testing it away from body. 18.Do not operate steamer without properly filling the water container. 19. Never yank cord to disconnect from outlet. Instead, grasp plug and pull to disconnect. 20.Burns could occur from touching hot metal parts, or proximity to hot water or steam.
GETTING TO KNOW YOUR STEAM PRESS 1.The Pressing Handle raises and lowers the Pressing Plate. 2.The Locking Knob will lock together the Pressing Plate and the Ironing Board. Use this to carry or store the Steam Press. 7 8 9 13 10 3.The Steam Burst Buttons on either side of the Pressing Handle produce a burst of steam when pressed. 12 4. The Pressing Plate it the temperature controlled surface that heats and presses the fabric. 6 7 8 2 9 5.
GETTING TO KNOW YOUR STEAM PRESS 10.The Temperature Control Buttons are used to select a desired temperature by cycling through the list of choices above the buttons. Push the Temperature Control Buttons until the indicator light beneath the type of material you are going to press becomes illuminated. 11.The Water Tank 12.The Pressing Cushion is a fabric covered pad used for pressing gathered or contoured areas such as sleeves, darts, yokes 13.
FEATURES OF THE STEAM PRESS Your Steam Press provides clean, professional results every time! .Pressing surface is fourteen times larger than most hand-held irons .Can reduce ironing time up to 50% .Multiple dry and steam settings, burst setting to remove stubborn wrinkles .Variable temperature control .Automatic shut off safety feature while open or closed with audible alert .Power indicator light .
OPERATION INSTRUCTIONS 7.Replace Water Reservoir Cap and push filled Water Reservoir back into main unit. *DO NOT ATTEMPT TO PULL WATER RESERVOIR OUT COMPLETELY. OPERATION INSTRUCTIONS 1.Turn the ON/OFF Switch to the"on"position. 2.Identify the type of fabric you will press and then select the temperature setting that matches the fabric to be pressed. It is best to start with the most delicate fabrics first, as higher heat will cause damage to Nylon and Silks. 3.Lay fabric flat on Ironing Board. 4.
TIPS PRESSING STEAM BURST 1.Hold Pressing Plate approximately 3" above Ironing Board. 2.Press Steam Burst Button to release a burst of steam onto fabric. 3.Lowr Pressing Plate onto fabric, then raise once again. 4.Repeat steps 1-3 above until fabric is smooth and wrinkle-free. IMPORTANT NOTE FOR BEST RESULTS, PRESS BUTTON FOR 2 SECONDS AND RELEASE. STEAMING TIPS Pressing Garments 1. Lay the garment on the Ironing Board. 2. Lower the steam plate and return to the open position after a few seconds.
TIPS PRESSING 4.Lower the Pressing Plate and then raise. 5.Repeat this process until all wrinkles have been removed. Shirts and Blouses 1.Place the shoulder yoke on the Ironing Board first and press. 1 2 2.Then place the sleeves on the Ironing Board with the fold parallel to the long seam and press 3.Place the cuffs on the end of the board and press. 4.Place the bottom o f the shirt behind Ironing board so that you begin pressing pressing the side with the pocket.
TIPS PRESSING Pants 1.Place the Pressing Cushion under the waistband and press, repositioning the waistband until completely pressed. 2.To press the in-seam, place the cushion under the area to be pressed. 3.Place the pleated area on the Ironing Board. Carefully fold pleats and press. 4.Embroidery should be placed face down on the Ironing Board to reduce wear and prevent damage to delicate areas.
TIPS PRESSING Other Techniques 1.Placing the pressing cushion between the fabric and the Pressing Plate may help with delicate fabrics. 2.Buttons and Zippers: if you have older types of buttons or zippers, you may need to take special care to avoid melting. In order to do so, place the garment face down and cover with a pressing cushion before pressing. 3.Spray bottle may be used to spray the fabric lightly. This will further help to remove stubborn wrinkles. 4.
CLEANING THE STEAM PRESS & STORAGE CLEANING THE STEAM PRESS 1.Place the Pressing Cushion in the middle of Ironing Board. 2.Place a clean towel over the Pressing Cushion and the Ironing Board. 3.Set the temperature control Button to its highest setting(LINEN). 4.When the Steam Burst Ready Indicator Light illuminates, lower Pressing Plate onto the pressing cushion. 5.Press the steam burst button six times. 6.Allow the Pressing Plate to cool. 7.Clean the pressing plate with a damp cloth. 8.
TROUBLE SHOOTING Before taking the unit to a service center, please check the following list of common problems for your issue. PROBLEM Unit fails to steam. Power Indicator Light does not illuminate. Unit fails to steam. Power Indicator Light does illuminate. Steam Burst output is weak or intermittent. POSSIBLE CAUSE SOLUTION Unit is not plugged in. Plug into electrical outlet. Household Circuit Breaker/ Ground Fault Interrupter has tripped or blown a fuse.
This electrical appliance complies with directive 2002/96/EC(Waste Electrical and Electronic Equipment----WEEE). The meaning of the crossed-through waste bin symbol on the appliance is that the product must be disposed of separately to other household waste at the end of the useful life of the appliance. The user is responsible for delivering the appliance to an appropriate collection centre at that time.