4423 Instruction Manual Manual de Instrucciones Manuel d'Instruction
EN IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic safety should always be followed, including the following: Read all instructions before using this sewing machine. DANGER - To reduce the risk of electric shock: 1. An appliance should never be left unattended when plugged in. 2. Always unplug this appliance from the electric outlet immediately after using and before cleaning. 3. Always unplug before changing the light bulb.
E IMPORTANTES INSTRUCCIONES DE SEGURIDAD Cuando se utiliza un dispositivo eléctrico, debe seguirse siempre precauciones de seguridad básica, incluyendo las siguientes: Leer todas las instrucciones antes de utilizar está máquina de coser. PELIGRO - Para reducir el riesgo de sacudidas eléctricas: 1. Un dispositivo eléctrico nunca debe dejarse desatendido cuando está conectado. 2. Desenchufar siempre la máquina de la toma de corriente inmediatamente despues de utilizarla y antes de su limpieza. 3.
F INSTRUCTIONS IMPORTANTES DE SÉCURITÉ Lors de l'utilisation d'un appareil électrique, il est important de toujours suivre certaines précautions de sécurité dont certaines sont les suivantes : Lire toutes les instructions avant d'utiliser votre machine à coudre : 7. 8. 9. DANGER - Pour éviter tout risque d'électrocution : 1. 2. 3. Lorsque la machine est branchée, ne jamais la laisser sans surveillance.
EN Congratulations As the owner of a new Singer sewing machine, you are about to begin an exciting adventure in creativity. From the moment you first use your machine, you will know you are sewing on one of the easiest to use sewing machines ever made. May we recommend that, before you start to use your sewing machine, you discover the many features and the ease of operation by going through this instruction book, step by step, seated at your machine.
EN List of contents Machine Basics Principle Parts of the Machine .........................................................................................................................................................2/4 Connecting Machine to Power Source................................................................................................................................................6 Two Step Presser Foot Lifter/ Adjusting Presser Foot Pressure ...............................................
E Indice Partes de la máquina Partes de la máquina .......................................................................................................................................................................3/5 Conexión de la máquina a la fuente de alimentación eléctrica ...........................................................................................................7 Elevador del prensatelas de dos tiempos/ Ajuste de la presión del prensatelas ..........................................
F Table des matières L'essentiel de la machine Les composantes principales de la machine à coudre ....................................................................................................................3/5 Branchement de la machine à une source d'alimentation ..................................................................................................................7 Levier du pied presseur à deux niveaux/ Réglage de la pression du pied-presseur ............................................
EN Principal Parts of the Machine 1. Thread tension dial 2. Presser foot pressure adjustment 3. Thread take-up lever 4. Reverse sewing lever 1 9 2 10 11 3 5. Thread cutter 6. Presser foot 12 4 7. Needle plate cover 5 8. Removable extension table/ accessory storage 9. Three needle position dial 13 6 10. Bobbin stopper 11. Stitch width dial 7 12. Stitch length dial 8 13. Pattern selector dial 14. Automatic threader 15.
E Partes de la máquina F Les composantes principales de la machine à coudre 1. Disco de tensión 2. Ajuste del prensatelas de presión 1. Réglage de la tension 3. Tirahilos 2. Commande de réglage de pression du pied-presseur 4. Palanca para coser hacia átras 3. Releveur du fil 5. Cortahilos 4. Levier de couture arrière 6. Prensatelas 5. Coupe fil 7. Placa de cubierta de canilla 6. Pied presseur 8. Mesa de coser convertible/ caja de accesorios 7. Couvercle de la canette 9.
EN Principal Parts of the Machine 16. Horizontal spool pin 17. Bobbin winding spindle 16 23 18. Hole for second spool pin 17 19. Handwheel 24 18 20. Buttonhole stitch balance adjustment slot 25 21. Power and light switch 19 22. Main plug socket 26 23. Bobbin thread guide 27 24. Upper thread guide 25. Face plate 20 26. Handle 21 27. Presser foot lifter 22 28. Drop feed control 29. Foot speed control 30.
E Partes de la máquina F Les composantes principales de la machine à coudre 16. Portacarrete 17. Devanador 16. Porte bobine horizontal 18. Orificio para el portacarrete auxiliar 17. Axe du bobineur 19. Volante 18. Trou pour insérer un deuxième axe de bobine 20. Ranura de ajuste del balance de ojales 19. Volant 21. Interruptor de encendido y apagado 20. Fente de réglage du point utilisé pour les boutonnières 22. Enchufe de conexión a la red. 21. Interrupteur d'alimentation et d'éclairage 23.
EN Connecting Machine to Power Source Connect the machine to a power source as illustrated. (1) This appliance is equipped with a polarized plug which must be used with the appropriate polarized outlet. (2) Attention: Unplug power cord when machine is not in use. A Foot control The foot control pedal regulates the sewing speed. (3) Attention: Consult a qualified electrician if in doubt of how to connect machine to power source. Unplug power cord when machine is not in use.
E Conexión de la máquina a la fuente de F Branchement de la machine à une source Conecte la máquina a una fuente de alimentación según se ilustra. (1) Esta máquina está provista de un conector polarizado, que debe utilizarse con una toma de corriente polarizada adecuada. (2) Brancher la machine comme indiqué ci-contre. (1) La fiche de la machine est dotée de broches normalisées et doit être utilisée avec une prise de courant conforme aux normes en vigueur.
EN Two Step Presser Foot Lifter When sewing several layers or thick fabrics, the presser foot can be raised to a higher position for easy positioning of the work. (A) A Adjusting Presser Foot Pressure The presser foot pressure of the machine has been pre-set and requires no particular readjustment according to the type of fabric (light-or-heavy weight). However, if you need to adjust the presser foot pressure, turn the presser adjusting screw with a coin.
E Elevador del prensatelas de dos tiempos F Levier du pied presseur à deux niveaux Cuando se cose varias capas de tela gruesa, el prensatelas puede elevarse a una posición alta para facilitar la colocación de la tela (A). Lorsque vous cousez plusieurs épaisseurs de tissus épais, le pied presseur peut être soulevé à un niveau plus élevé afin de faciliter le positionnement du tissu. Faire attention lorsque vous cousez plusieurs épaisseurs et travailler lentement (A).
EN Accessories 1 Standard accessories Standard accessories (1) a. All purpose foot b. Zipper foot c. Buttonhole foot d. Button sewing foot e. Seam ripper/ brush f. Edge/ quilting guide g. Pack of needles h. Spool holders i. Bobbin (3x) j. L-screwdriver k. Auxiliary Spool Pin l. Spool pin felt m.
E Accesorios F Accessoires Accesorios incluidos (1) a. Prensatelas universal b. Prensatelas para cremalleras c. Prensatelas para ojales d. Prensatelas para coser botones e. Brocha descosedor f. Guía para coser bordes/ edredones g. Paquete de agujas h. Portacarrete i. Bobinas (3x) j. Destornillador plano k. Portacarrete Auxiliar l. Sujetador de la bobina con fieltro m. Cubierta para máquina Accessoires standards (1) a. Pied multi-usage b. Pied pour fermeture-éclair c. Pied pour boutonnière d.
EN Winding the Bobbin - Place thread and corresponding spool holder on to spool pin. (1/2) - Snap thread into thread guide. (3) - Wind thread clockwise around bobbin winder tension discs. (4) - Thread bobbin as illustrated and place on spindle. (5) - Push bobbin spindle to right. (6) - Hold thread end. (7) 1 - Step on foot control pedal. (8) - Cut thread. (9) 3 2 - Push bobbin spindle to left (10) and remove.
E Devanado de la bobina F Remplissage de la canette - Coloque el hilo y sujete con la tapa grande o pequeña el poste. (1/2) - Placer le fil et le support correspondant sur le porte bobine. (1/2) - Deslice el hilo del carrete a través de la guía del hilo superior. (3) - Glisser le fil dans le guide. (3) - Enrouler le fil dans le sens horaire autour des disques de tension de l'enrouleur de canette.
EN Inserting the Bobbin When inserting or removing the bobbin, the needle must be fully raised. 1. Insert the bobbin in the bobbin case with the thread running counterclockwise direction (arrow). 2. Pull the thread through the slit (A). 3. Draw the thread clockwise until it slips into the notch (B). 4. Pull out about 15 cm (6 inches) of thread and attach the bobbin cover plate. (C) A Attention: Turn power switch to off ("O") before inserting or removing the bobbin.
F Insertion de la canette E Colocación de la bobina Cuando se inserte o retire la canilla, la aguja debe estar completamente elevada. Lorsque vous insérez ou retirez une canette, assurezvous que l'aiguille est complètement relevée. 1. Inserte la canilla en su cápsula con el hilo girando a la izquierda (sentido de la flecha). 1. Insérer la canette dans son logement, le fil étant orienté dans le sens anti-horaire (flèche). 2. Pase el hilo a través de la hendidura (A). 2.
EN Threading the Upper Thread This is a simple operation but it is important to carry out correctly as by not doing so several sewing problems could result. - Start by raising the needle to its highest point (1), and continue turning the handwheel counterclockwise until the needle just slightly begins to descend. Raise the presser foot to release the tension discs. Note: For safety, it is strongly suggested you turn off the power before threading. - Lift up the spool pin.
E Enhebrado del hilo superior F Enfilage supérieur Se trata de una operación sencilla pero es importante realizarla correctamente pues de no hacerlo podría surgir varios problemas en la costura. Cette opération est simple. Il est important de l'exécuter correctement sous peine de faire éventuellement face à plusieurs problèmes de couture. - Comience elevando la aguja a su posición más alta (1) y también eleve el prensatelas para liberar los discos de tensión.
EN Automatic Needle Threader - Raise the needle to its highest position. - Press lever (A) down as far as it will go. - The threader automatically swings to the threading position (B). - Pass thread around thread guide (C). A - Pass the thread in front of the needle around the hook (D) from bottom to top. B - Release lever (A). C - Pull the thread through the needle eye.
E Ensartador automático de la aguja F Enfileur automatique d'aiguille - Eleve la aguja a su posición más alta. - Relever l'aiguille à sa position la plus haute. - Presione la palanca (A) hacia abajo lo más posible en su recorrido. - Abaisser le levier (A) le plus possible. - L'enfileur se met automatiquement en position d'enfilage (B). - El ensartador oscila automáticamente a la posición de enhebrado. (B) - Faire passer le fil autour du guide-fil (C).
EN Raising the Bobbin Thread Hold the upper thread with the left hand. Turn the handwheel (1) towards you (counterclockwise) lowering, then raising needle. Note: If it is difficult to raise the bobbin thread, check to make sure the thread is not trapped by the hinged cover or the Removable Extension Table. 1 Gently pull on the upper thread to bring the bobbin thread up through the needle plate hole. (2) Lay both threads to the back under the presser foot.
F Pour remonter le fil de canette E Elevación del hilo de la bobina Sujete el hilo superior con la mano izquierda. Gire el volante (1) hacia usted hasta que baje totalmente la aguja, siga girando hasta volver a subir la aguja. Tenir le fil supérieur avec la main gauche. Tourner le volant (1) vers vous (sens anti-horaire) pour abaisser et lever l'aiguille.
EN Thread Tension Upper thread tension Basic thread tension setting: "4". (1) To increase the tension, turn the dial to the next number up. To reduce the tension, turn the dial to the next number down. A. Normal thread tension for straight stitch sewing. B. Thread tension too loose for straight stitch sewing. Turn dial to higher number. C. Thread tension too tight for straight stitch sewing. Turn dial to lower number. D. Normal thread tension for zig zag and decorative sewing.
F Tension du fil E Tensión del hilo Tension du fil supérieur Réglage de base pour la tension du fil: "4". (1) Pour augmenter la tension, tourner le cadran de réglage de la tension vers une valeur plus élevée. Pour réduire la tension, tourner le cadran de réglage de la tension vers une valeur inférieure. A. Tension du fil correcte pour une couture à point droit. B. La tension du fil est trop faible pour une couture à point droit. Tourner le cadran de réglage de la tension vers une valeur plus élevée. C.
EN How to Choose Your Pattern The diagram on this page display the stitch patterns available on the machine. a b c Stitches in the top of the diagram are indicated on the Pattern Selector Dial in gray. To select the patterns indicated with the gray color, turn the Pattern Selector Dial. (e) Use the Stitch Length Dial (d) to adjust the stitch length as desired for the project. Use the Stitch Width Dial (c) to adjust the width of the stitch as desired.
F Comment choisir votre motif E Cómo seleccionar su puntada El diagrama en esta página muestra los diseños de las puntadas disponibles en la máquina. Le diagramme sur la page précédente présente les motifs de point disponibles sur la machine. Las puntadas en la parte superior del diagrama están señaladas con gris en el Selector de Puntada. Para elegir los patrones indicados en color gris gire el selector de puntada.
EN Three Needle Position Dial The needle position can be altered with the "Three needle position dial". For normal work, the needle position is middle. For edge stitching or sewing parallel lines of top stitch, select needle position left or right. For twin needle stitching, needle position is middle. L M R a b a. Straight b. Zig-zag L. Left Needle Position M. Middle Needle Position R.
F Molette trois position d'aiguille E Guía de cambio de posición de la aguja La posición de la aguja puede ser cambiada utilizando el Guía de Cambio de Posición de la Aguja. Para trabajo normal, la posición de la aguja es en el centro. Para puntadas al borde de la tela o para costuras de líneas paralelas, seleccione la posición izquierda o derecha. Para puntadas con la doble aguja, la posición es en el centro.
EN Stitch Width Dial & Stitch Length Dial Function of stitch width dial The maximum zigzag stitch width for zigzag stitching is 5mm; however, the width can be reduced on any patterns. The width increases as you move zigzag dial from "0" - "6". (1) The Stitch Width Dial is also the control for the straight stitch infinite needle position. "0" position is full left, "6" is full right and between "2" and "3" is center needle position.
E Selector de ancho de puntada y F Cadran de largeur de point et cadran de Selector de largo de puntada longueur de point Fonction du cadran de largeur de point La largeur maximum de point zigzag pour la couture en zigzag est 5mm ; toutefois, la largeur peut être réduite sur n'importe quel motif. La largeur augmente au fur et à mesure que vous déplacez le cadran de zigzag de "0" à "6". (1) Le cadran de largeur de point contrôle également la position d'aiguille infini au point droit.
EN Sewing Straight Stitch To begin sewing, set the machine for straight stitch. (1) Place the fabric under the presser foot with the fabric edge lined up with the desired seam guide line on the needle plate. (2) Lower the presser foot lifter, and then step on the foot controller to start sewing.
F Couture au points droits E Puntada recta Para comenzar a coser, gire el selector de puntadas en la puntada recta, puede seleccionar la posición de la aguja en centro o a la derecha. (1) Pour commencer à coudre, régler la machine sur le point droit. (1) Placer le tissu sous le pied presseur avec le bord du tissu aligné au guide de couture souhaité sur la plaque à aiguilles. (2) Coloque la tela bajo prensatelas con el borde de la tela alineado con la línea de guía deseada de la costura en la placa aguja.
EN Reverse Sewing To secure the beginning and the end of a seam, press down the reverse sewing lever (A). Sew a few reverse stitches. Release the lever and the machine will sew forward again. (1) A Removing the Work Turn the handwheel toward you (counterclockwise) to bring the thread take up lever to its highest position, raise the presser foot and remove work behind the needle and presser foot. (2) 1 2 Cutting the Thread B Pull the threads under and behind the presser foot.
E Remate F Couture en marche arrière Para fijar el comienzo y el final de la costura, presione la palanca de retroceso. Haga unas pocas puntadas hacia atrás. Suelte la palanca y la máquina coserá de nuevo hacia delante (A). (1) Afin de renforcer le début et la fin d'une couture, abaisser le bouton marche arrière. Faire quelques points en marche arrière. Lâcher le bouton (A) et la machine reprendra la couture vers l'avant.
EN Choosing Stretch Stitch Patterns The Stretch Stitch Patterns are indicated with a blue color on the Pattern Selector Dial. To select these stitches, turn the Pattern Selector Dial to the desired pattern. Then, turn the Stitch Length Dial to the indicator marked "S1". Though there are several stretch patterns, here are two examples: M Straight Stretch Stitch (1) Set the Pattern Selector Dial to " ". Used to add triple reinforcement to stretch and hardwearing seams.
E Selección de Puntadas elásticas F Choisir les motifs de point extensible Les motifs de point extensible sont indiqués en bleu sur le cadran de sélection de motifs. Pour sélectionner ces points, tourner le cadran de sélection de motifs sur le motif souhaité. Puis, tourner le cadran de longueur de point sur l'indicateur marqué par "S1".
EN Blind Hem For hems on curtains, trousers, skirts, etc. Blind hem for stretch fabrics. Blind hem for firm fabrics. M Set the Stitch Length Dial with the range shown on the diagram at the right. Blind hems, however, are normally sewn with a longer stitch length setting. Set the Stitch Width Dial at a setting appropriate for the weight/type of fabric being sewn, within the range shown in the diagram on the right of the page.
E Dobladillo Invisible F Ourlet invisible Pour les ourlets sur les rideaux, pantalons, jupes, etc. Para dobladillos, cortinas, pantalones, faldas, etc. Ourlet invisible pour tissus extensibles. Para realizar un dobladillo invisible en telas elásticas, seleccione esta puntada. Ourlet invisible pour tissus solides. Régler le cadran de longueur de point dans la gamme tel qu'indiquée sur le diagramme à droite.
EN Sew 1-step Buttonholes Buttonhole sewing is a simple process that provides reliable results. However, it is strongly suggested to always make a practice buttonhole on a sample of your fabric and stabilizer. M Making a Buttonhole 1. Using tailor's chalk, mark the position of the buttonhole on the fabric. 2. Attach the buttonhole foot and set the Pattern Selector Dial to " ". Set stitch length dial to " ". Set the stitch width at "6". The width however may need to be adjusted according to the project.
E Ojal de un sólo paso F Couture de boutonnières en 1 étape Confeccionar ojales es un proceso sencillo que proporciona resultados confiables. Sin embargo, se recomienda realizar siempre un ojal de práctica en una muestra de tela e intercalar. La couture de boutonnière est un processus simple qui assure des résultats fiables. Toutefois, il est fortement suggéré de toujours réaliser une boutonnière d'essai sur un échantillon de tissu et d'entoilage. Confección de un ojal 1.
EN Left and Right Side Balance for Buttonhole Stitch density on right and left sides of buttonhole can be adjusted by buttonhole balance control dial. This dial should usually be in a neutral position (between "+" and "–") If the stitches on the left side of buttonhole are too close together, turn the dial to the left (+). * Turning dial to the left opens left side. If the stitches on the left side of the buttonhole are too open, turn the dial to the right (–). * Turning dial to right closes left side.
E Balance a izquierda y derecha para F Équilibrage gauche et droit pour coser ojales boutonnière La densidad de la puntada en los lados derecho e izquierdo del ojal puede ajustarse por el mando de control del balance del ojal. Este selector debe estar normalmente en una posición neutral. (entre "+" y "–") La densité des points de part et d'autre de la boutonnière peut être réglée au moyen du sélecteur d'équilibrage de boutonnière.
EN Sewing on Buttons Move the drop feed control to right side to lower the feed dogs. (1) L Change the all purpose foot to the button sewing foot. (2) Set the stitch length to "0". Place the button and fabric under the Button Sewing foot, as illustrated in (3). Set the machine for zig-zag stitch, then set the width to number "3" - "6". Turn the handwheel to check that the needle goes cleanly into the left and right holes of the button.
E Pegado de botones F Couture de boutons Mueva el control del alimentador hacia la derecha para bajar los dientes de alimentación. (1) Déplacer le levier d'abaissement des griffes " " vers la droite pour abaisser le système d'entraînement des griffes. (1) Cambie el prensatelas especial para coser botones.(2) Ajuste el largo de puntada en "0". Changer le pied presseur multi-usage pour le pied de couture de bouton. (2) Régler la longueur de point sur "0".
EN Installing the Removable Extension Table Hold the removable extension table horizontally, and push it in the direction of the arrow. (1) To remove the extension table, pull it toward the left. 1 The inside of the removable extension table can be utilized as an accessory box. To open, flip cover down as shown.
E Instalación de la cubierta removible F Installation du bras amovible Coloque la máquina en una superficie estable, empuje la cubierta removible como indica la flecha, y luego jale hacia afuera. (1) Maintenir le bras amovible en position horizontal et le pousser dans la direction de la flèche. (1) Pour enlever le bras amovible le tirer vers la gauche. El interior de la cubierta removible, se puede utilizar para guardar los accesorios de la máquina.
EN Attaching the Presser Foot Shank Raise the presser bar (a) with the presser foot lifter. Attach the presser foot shank (b) as illustrated. (1) a a Attaching the presser foot Lower the presser foot shank (b) using the presser foot lifter, until the cut-out (c) is directly above the pin (d). (2) The presser foot (f) will engage automatically. e Removing the presser foot Raise the presser foot using the presser foot lifter. (3) Raise the lever (e) and the foot disengages.
E Colocación del portaprensatelas F Installer le support du pied presseur Eleve la barra del prensatelas (a). Coloque el portaprensatelas (b) según se ilustra (1). Relever la barre du pied (a) avec le releveur de pied presseur. Attacher le support du pied presseur (b) comme illustré. (1) Colocación del prensatelas Baje el portaprensatelas (b) hasta que el corte (c) esté directamente encima del perno (d).
EN Needle/ Fabric/ Thread Chart NEEDLE, FABRIC, THREAD SELECTION GUIDE NEEDLE SIZE FABRICS Lightweight fabrics-thin cottons, voile, silk, muslin, 9-11 (70-80) interlocks, cotton knits, tricots, jerseys, crepes, woven polyester, shirt & blouse fabrics. 11-14 (80-90) 14 (90) 16 (100) 18 (110) Medium weight fabrics-cotton, satin, kettlecloth, sailcloth, double knits, lightweight woolens. Medium weight fabrics-cotton duck, woolen, heavier knits, terrycloth, denims.
E Guía de selección de agujas/ telas/ hilos GUÍA DE SELECCIÓN DE AGUJAS/ TELAS/ HILOS CALIBRE DE LA AGUJA TELA HILO 9-11 (70-80) Telas de poco peso - algodones delgados, Voile, sarga, seda, muselina, interlocks (puntadas entrelazadas), tejidos de algodón, tricots, jerseys, crepés, poliester tejido, telas para camisas y blusas. Hilo ligeros en algodón, nylon, poliester o poliester bordado. 11-14 (80-90) Telas de peso medio, raso, lona, tela de velas, géneros de punto doble, tejidos de lana.
F Table de correspondance de l'aiguille, du tissu et du fil GUIDE DE SÉLECTION DE L'AIGUILLE, DU TISSU ET DU FIL DIMENSIONS DE L'AIGUILLE TISSUS FIL 9-11 (70-80) Tissus légers, cotons légers, voile, serge, soie, mousseline, Qiana, tissu interlock, tricots de coton, tricots, jerseys, crêpes, polyester tissé, tissus pour chemises et blouses. File de coton léger, nylon, polyester ou de coton enrobé de polyester.
EN How To Drop Feed Dog For ordinary sewing, keep the feed dog up, for freehand embroidery, sewing on buttons and darning, drop the feed dog. To raise (a) and lower (b) feed dog.
E Ocultacion del transportador F Comment abaisser les griffes d'entraînement Los dientes de arrastre están en posición arriba para los trabajos de costura habituales. Les griffes d'entraînement reste en position haute pour les travaux de couture ordinalre. Colocar la palanca (a) hacia la izquierda. Pour le reprisage, broderie à main levée, et coudre les boutons. Il faut abaisser les griffes d'entraînement. Pousser le levier (b) vers la droite (2).
EN Inserting & Changing Needles Change the needle regularly, especially if it is showing signs of wear and causing problems. For best sewing results ® always use SINGER Brand Needles. D A Insert the needle as illustrated as follows: A. Loosen the needle clamp screw and tighten again after inserting the new needle. (1) B. The flat side of the shaft should be towards the back. C/D.Insert the needle as far up as it will go.
E Colocación y cambio de agujas F Insertion et changement d'aiguille Cambie la aguja periódicamente, sobre todo si muestra signos de desgaste y origina problemas. Para mejores resultados de la costura, utilice siempre agujas originales de ® SINGER . Remplacer l'aiguille régulièrement, plus particulièrement si elle indique des signes d'usure et cause des problèmes. Pour obtenir les meilleurs résultats, toujours utiliser des aiguilles ® fabriquées par SINGER .
EN Changing the Bulb Disconnect the machine from the power supply by removing the plug from the main socket! Replace bulb with same type rated 15 watts (110-120V area / 220-240V area). - Loosen screw (A) as illustrated. (1) Remove the face plate (B). Unscrew the bulb and install a new one (C). (2) Replace the face plate and tighten screw. B A ® Should there be any problem, consult your SINGER retailer.
E Cambio de la bombilla F Changement de l'ampoule Desconecte la máquina de la alimentación principal retirando el conector desde la toma de corriente. Sustituir la bombilla con otra del mismo tipo de 15 voltios (tensión de 110-120V área / 220-240V área). Débrancher la machine de l'alimentation électrique en retirant la prise! Remplacer l'ampoule par une ampoule du même type de 15 Watts (pour 110-120V / 220-240V). - Afloje el tornillo (A) según se ilustra. (1) - Retire la placa frontal (B).
EN Troubleshooting Guide Problem Cause Correction Upper thread breaks 1. The machine is not threaded correctly. 2. The thread tension is too tight. 3. The thread is too thick for the needle. 4. The needle is not inserted correctly. 5. The thread is wound around the spool holder pin. 6. The needle is damaged. 1. Rethread the machine. 2. Reduce the thread tension. (lower number) 3. Select a larger needle. 4. Remove and reinsert the needle. (flat side towards the back) 5.
E Problemas y soluciones Problema Causa Solución El hilo superior se rompe 1. 2. 3. 4. 5. 6. La máquina está mal enhebrada. La tensión del hilo es demasiado fuerte. El hilo es demasiado grueso para la aguja. La aguja no está colocada correctamente. El hilo se ha enredado en la caja bobina. La aguja está torcida o despuntada. 1. 2. 3. 4. 5. 6. Enhebrar la máquina correctamente. Disminuir la tensión del hilo superior. (número menor) Usar una aguja más gruesa. Colocar la aguja correctamente.
F Guide de dépannage Problème Cause Solution Le fil supérieur casse 1. La machine n'est pas correctement enfilée. 2. La tension du fil est trop élevée. 3. Le fil est trop gros pour l'aiguille. 4. L'aiguille n'est pas bien insérée. 5. Le fil est enroulé autour du porte bobine. 6. L'aiguille est endommagée. 1. Réenfiler la machine. 2. Réduire la tension. (valeur inférieure) 3. Choisir une aiguille plus grosse. 4. La retirer et la réinsérer. (côté plat vers l'arrière) 5.
021Q5D0101(A)( ) Jun/10 SINGER 4423(Q50DST)