User Guide
Table of Contents Introduction . . . . . . . . . . . . . . . . . . . 5 Appendix: Manual Network Configuration . . . . . . . . . . . . . . . . 65 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Safety and Care Information . . . . . . . . . . 7 What’s in the Box? . . . . . . . . . . . . . . . . . . . 9 SIRIUS TTR1 Radio Functions . . . . . . . . . 10 Remote Control . . . . . . . . . . .
Introduction 5
Introduction Features Congratulations, on your purchase of the SIRIUS TTR1 Radio! Your new SIRIUS TTR1 Radio comes with everything you need to enjoy SIRIUS Internet Radio in your home. Use this manual to familiarize yourself with all of your SIRIUS TTR1 Radio features and capabilities. For the latest information about your SIRIUS TTR1 Radio and other SIRIUS products and accessories, visit http://www.sirius.com.
Safety and Care Information IMPORTANT! Always read and understand all the instructions to avoid injury to yourself and/or damage to your device. SIRIUS XM Radio Inc. disclaims all responsibility for damage from data loss due to breakdown, repair, or other causes. • Do not expose to extreme temperatures (above 140ûF or below -4ûF, or above 60ûC or below -20ûC). • Do not expose to moisture. Do not use device near or in water. • Do not let any foreign matter spill into device. • Do not store in dusty areas.
Introduction • Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. • Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety.
What’s in the Box? TUNE 1 2 3 4 5 6 7 8 9 0 BACK VOL MENU ALARM 1 ALARM 2 SIRIUS TTR1 Radio BACK OK MUTE MENU 1 2 3 5 6 7 4 8 9 0 ALARM 1 ALARM 2 Remote Control 9
Introduction SIRIUS TTR1 Radio Functions TUNE Knob (Multifunction) (page 26) Turning the knob at the default display screen displays the category tune screen; pressing the knob at the default display screen displays the direct tune screen; turning the knob in a menu or user input screen scrolls through menus and choices; pressing the knob in a menu or user input screen selects a highlighted item; pressing and holding displays the Parental control menu. Power Button (page 26) Turn radio On and Off.
Snooze/Sleep Timer Button (page 27) Mutes the alarm, or sets the sleep timer, for 5, 10, 15, 30, 45, or 60 minutes.
Introduction Remote Control Power Button Turn radio On and Off. Arrow Buttons Press to scroll through lists; also highlight menu options. OK Button Press to select channel list and menu items. BACK BACK Button Press to return back to the previous display screen. MENU Button Press to access or exit advanced features and configuration options. 0-9 Number Buttons Set and select channel presets or directly enter channel numbers. 12 OK MUTE +/— Buttons Press to increase or decrease the audio volume.
Display Screen When using the SIRIUS TTR1 Radio, information about songs and artists, and radio functions are displayed.
Installation 15
Installation Introduction The SIRIUS TTR1 Radio allows you to listen to all of the channels on your Premium SIRIUS Internet Radio subscription package using either a wireless Internet connection (Wi-Fi), or using a wired Ethernet connection. You must be subscribed to the Premium SIRIUS Internet Radio service to use the SIRIUS TTR1 Radio. Go to www.sirius.com/siriusinternetradio or call 888-539-7474 to subscribe and get your user name and password.
Step 1: Connect to a Network The Network Wizard feature is the easiest way to connect to a wireless network. It searches for available wireless networks and displays a list of wireless networks found for you to select. However, if your wireless network name (SSID) is hidden, or if your network is DHCP disabled, you’ll have to manually enter the network settings rather than using the Network Wizard.
Installation To connect to a wireless network using the Network Wizard If the wireless network is secured, you’ll need to enter the key (password) for the wireless network during the connection procedure. If you don’t know the password, contact your network administrator of the person who setup the wireless network. a. If you have just turned your SIRIUS TTR1 Radio on for the first time, the SSID screen will already be displayed. Skip ahead to step e. b.
displayed and the radio will connect to the wireless network. Skip to step h. Key: If you choose a network that is secured, you will be prompted to 0123456789., ab BKSP enter the key (password). If you cdefghijklmnopq OK don’t know the password, contact rstuvwxyzABCDEF your network administrator of the GHIJKLMNOPQRSTU CANCEL person who setup the wireless network. Remember that the key is case sensitive. Turn the TUNE knob to scroll through the list of characters and highlight each character.
Installation If you have previously entered your SIRIUS user name and key into the radio, and had tuned to a channel, the screen will show Connecting. When successfully connected, the Buffering... screen will be displayed as the channel information is streamed to the radio. When complete, you are returned to the main display screen and you should hear the audio playing. Otherwise, the Category Tune screen is displayed. SIRIUS SIRIUS Hits 1 3:13PM Connecting. SIRIUS Hits 1 3:14PM Buffering...
To connect to a wired network using the Network Wizard: a. At the rear of the radio, remove the compartment cover and connect an Ethernet cable to the Ethernet connector on the inside left of the compartment. Refer to “Wired Ethernet Connector” on page 11 for the location of the Ethernet connector. Replace the compartment cover. b. Connect the other end of the Ethernet cable to your home’s wired network. c.
Installation is displayed, check the Ethernet cable connections. Network settings i. If you are installing your SIRIUS TTR1 Radio for the first time, continue with “Step 2: Enter Your SIRIUS Account Information” on page 23. If you have previously entered your SIRIUS user name and key into the radio, and had tuned to a channel, the screen will show Connecting. When successfully connected, the Buffering... screen will be displayed as the channel information is streamed to the radio.
Step 2: Enter Your SIRIUS Account Information The SIRIUS TTR1 Radio needs your account user name and password to connect to SIRIUS Internet Radio service. If are not yet subscribed to the SIRIUS Internet Radio service, go to www.sirius.com/siriusinternetradio or call 888-539-7474 to subscribe, and get your user name and password. To enter your account information: a. Turn on the radio by pressing the Power button. b. Press MENU and turn the TUNE knob to highlight SIRIUS Setup. Press the TUNE knob. c.
Installation scroll to highlight OK and press the TUNE knob. f. You will then be prompted to enter your password. Enter your password in the same way as you entered your user name and then select OK. Note that the password is case sensitive. g. The radio will attempt to connect to the SIRIUS Internet Radio service. If the user name and password you entered is incorrect, the Login failed screen will be displayed. You’ll have to re-enter the correct user name and password.
Using Your SIRIUS TTR1 Radio 25
Using Your SIRIUS TTR1 Radio Navigation Basics Power Button The Power button turns the SIRIUS TTR1 Radio On or Off. Tune Knob TUNE The TUNE knob is multifunction— you can turn it clockwise or counterclockwise, and press it. • Turn: Turning the TUNE knob when at the main display screen displays the Category tune screen. When in menus or user input screens, turning the TUNE knob scrolls up or down through menus and user choices.
BACK Button BACK The BACK button returns back to the previously displayed screen. MENU Button MENU Pressing the MENU button from the main display screen accesses the advanced features and configuration options menu, where you can browse the channel categories and channels, and change the radio settings. Pressing it when in the configuration options menu returns the radio to the main display screen.
Using Your SIRIUS TTR1 Radio Listening to SIRIUS Internet Radio Tune a Channel: 1. Press MENU. 2. Press the TUNE knob to select Category Tune. 3. Press the TUNE knob to select All All channels 001-SIRIUS Hits 002-The Blend 003-SIRIUS XM Love 004-40s on 4 005-50s on 5 Channels to browse through all the channels, or turn the TUNE knob to highlight a category. Press the TUNE knob to select the category. 4. Turn the TUNE knob browse through the channels, and highlight a channel to tune.
2. Press the TUNE knob to select Category Tune. Pop 001-SIRIUS Hits 1 002-The Blend 4. Press the TUNE knob to select the 003-SIRIUS XM Love category and view the channels in the 004-40s on 4 category. 005-50s on 5 3. Turn the TUNE knob to browse through and highlight a category. Returning to Main Display Screen When in the advanced features and configuration options menu, pressing MENU will return you to the main display screen.
Using Your SIRIUS TTR1 Radio Direct Tune A channel can be tuned directly by entering the channel number. 1. From the main display screen, press the TUNE button. 2. Use the 0-9 number buttons on the radio or Remote Control to enter the channel number. If you make a mistake, turn the TUNE knob to highlight BKSP and press the TUNE knob erase the character. Direct Tune BKSP OK CANCEL 3. When the channel number is entered, turn the TUNE knob to highlight OK. Press the TUNE knob to tune the channel.
Favorite Channels You can assign up to 10 of your favorite channels to a number button (0-9) so you can easily tune them. To assign a favorite channel to a number button: 1. Tune to the channel you want as a favorite. 2. Press and hold a number button (0-9) for one second to assign the channel as a favorite (preset) to that button. Preset stored IMPORTANT! If the button you choose already has a favorite channel assigned to it, it will be replaced with the new favorite channel.
Using Your SIRIUS TTR1 Radio Alarm Clock Your SIRIUS TTR1 Radio has two alarm clocks which can be configured according to your liking. When the radio is off, and the alarm(s) are on, the times of each alarm are displayed on the screen. 4:54 1 AM 2 Before you configure the alarm clock, refer to “Clock Setup” on page 53 and ensure that the Time Zone and Daylight Savings Time are set correctly. To turn the alarm clocks On or Off: 1.
4. The Alarms screen summarizes each alarm clock setting. To configure an alarm, turn the TUNE knob to scroll to and highlight Alarm 1 or Alarm 2. Press the TUNE knob. 5. Each alarm has 5 configuration options which are summarized in the following table at the beginning of this section. To change an option, turn the TUNE knob to scroll to and highlight the option. Press the TUNE knob to configure the option.
Using Your SIRIUS TTR1 Radio Snooze When the alarm sounds, pressing the Sleep/Snooze button will silence the alarm for a period of time. After the snooze time elapses, the alarm will sound again. To snooze: 1. Press the Snooze/Sleep button on the top of the radio. The radio will display a snooze time of 05 minutes. Set snooze time 05 minutes 2. Each immediate subsequent press of the Snooze/Sleep button increases the snooze time to 10, 15, 30, 45, or 60 minutes. 3.
Sleep Timer The sleep timer turns the radio off after a period of time as you fall asleep. The time can be set to turn the radio off after 5, 10, 15, 30, 45, or 60 minutes. To turn the sleep timer On: Set sleep time 1. Press the Snooze/Sleep button on the top of the radio. The radio will display a sleep time of 05 minutes. 05 minutes 2. Each subsequent press of the Snooze/ Sleep button increases the sleep time to 10, 15, 30, 45, or 60 minutes. 3.
Using Your SIRIUS TTR1 Radio Parental Control Your SIRIUS TTR1 Radio has a parental control feature which will allow you to lock access to channels. A 4-digit code controls access to the locked channel or locked category. When you browse a category, the locked channel will have an L displayed to the right of the channel name.
3. Turn the TUNE knob to highlight Change lock code. Press the TUNE knob. 4. You will be prompted to enter the original lock code. If this is the first time you are changing the lock code, enter 1111, otherwise enter your existing lock code. Use the 0-9 number buttons on the radio or Remote Control to enter the Enter orginal code lock code. If you make a mistake, turn the TUNE knob to highlight BKSP and BKSP press the TUNE knob to erase the character.
Using Your SIRIUS TTR1 Radio 8. Press MENU to exit. To turn Parental control Off: 1. Press and hold the TUNE knob. 2. Lock/Unlock will be highlighted. Press the TUNE knob. 3. You will be prompted to enter your 4-digit lock code. Use the 0-9 number buttons on the radio or Remote Control to enter the lock code. If you make a mistake, turn the TUNE knob to highlight BKSP and press the TUNE knob to erase the character.
To lock or unlock channels: 1. Press and hold the TUNE knob. 2. Turn the TUNE knob to scroll through the list and highlight Lock channels. Press the TUNE knob. 3. If parental control is On (locked), you will be prompted to enter your 4-digit code, otherwise skip to step 4. Use the 0-9 number buttons on the radio or Remote Enter lock code Control to enter the lock code. If you make a mistake, turn the TUNE knob BKSP to highlight BKSP and press the TUNE knob to erase the character.
Using Your SIRIUS TTR1 Radio To unlock a channel, highlight a locked channel and press the TUNE knob. The L lock indicator will be removed Parental lock indicating that the channel is unlocked. 5. Continue to lock or unlock channels until you are done. When complete, press MENU. You will be prompted to save the parental lock list. Turn the TUNE knob to highlight YES and press the TUNE knob. 6. A confirmation screen will be displayed. Press MENU to exit.
knob to erase the character. When you have selected all 4 digits of your code, turn the TUNE knob to highlight OK and press the TUNE knob. 4. If you have entered the correct lock code, the channel will begin playing. Once you have unlocked one channel, all locked channels become unlocked and will remain unlocked until you turn the radio Off. The next time you turn the radio On, all channels will be locked.
Using Your SIRIUS TTR1 Radio Equalization (EQ) You can adjust the equalization profile of the radio to adjust for room acoustics and your listening pleasure. The profiles for EQ equalization are Flat, Loudness, Bass Boost, Bright, EQ Profiles and Vocal Boost. Spatialization > Another adjustment option is spatialization. Spatialization makes the radio sound like it is in a three-dimensional environment. By default, spatialization is on, but can be turned off. To change the equalization profile: 1.
To turn spatialization on or off: 1. Press MENU. 2. Turn the TUNE knob to scroll to and highlight EQ. Press the TUNE knob. 3. Turn the TUNE knob to scroll to and highlight Spatialization. Press the TUNE knob. Spatialization Spatialization ON* OFF 4. Turn the TUNE knob to highlight ON or OFF and press the TUNE knob. 5. Press MENU to exit.
Configuring Your SIRIUS TTR1 Radio 45
Configuring Your SIRIUS TTR1 Radio SIRIUS setup The SIRIUS setup menu option allows you to configure your user name and password for the SIRIUS Internet Radio service. You SIRIUS setup can also check the status of your connection. User name If are not yet subscribed to the SIRIUS Internet Radio Password Status service, go to www.sirius.com/siriusinternetradio or call 888-539-7474 to subscribe, and get your user name and password. To test whether you are subscribed to service, go to www.sirius.
2. Turn the TUNE knob to scroll to and highlight SIRIUS setup. Press the TUNE knob. 3. User name will be highlighted. Press the TUNE knob. 4. Turn the TUNE knob to scroll through the list of characters and highlight each character for your user name. Press the TUNE knob to select the highlighted character and move to the next character. If you make a mistake, turn the TUNE knob to highlight BKSP and press the TUNE knob erase the character.
Configuring Your SIRIUS TTR1 Radio 4. Turn the TUNE knob to scroll through the list of characters and highlight each character for your password. The password is case sensitive. Press the TUNE knob to select the highlighted character and move to the next character. If you make a mistake, turn the TUNE knob to highlight BKSP and press the TUNE knob erase the character. Password 0123456789 abcd BKSP efghijklmnopqrs OK tuvwxyzABCDEFGH IJKLMNOPQRSTUVW CANCEL 5.
Status The Status screen shows the current status of your Premium SIRIUS Internet Radio service, the user name you are using, and the bit rate of your connection. To display the status: 1. Press MENU. 2. Turn the TUNE knob to scroll to and highlight SIRIUS setup. Press the TUNE knob. 3. Turn the TUNE knob to scroll to and highlight Status. Press the TUNE knob. Status Active User name: your_user_name Bit rate: HIGH 4. The Status screen will be displayed. Press MENU to exit.
Configuring Your SIRIUS TTR1 Radio System Setup The System Setup menu option offers the following menu items: SIRIUS AUX in Alarms Alarm 1: Alarm 2: Brightness Clock Setup Set Time/Date Auto Update Time Zone Daylight savings Network Network wizard View Settings Manual Settings Network profile Factory reset Software update Auto-check setting Check now Info page 51 page 51 page 52 page 52 page 52 page 52 page 53 page 53 page 54 page 54 page 55 page 56 page 56 page 57 page 58 page 58 page 60 page 61 page 61 p
SIRIUS and AUX in These two menu options select what the radio will play— SIRIUS selects the SIRIUS Internet Radio service to be played, and AUX in selects the auxiliary input to be played. You can connect a CD or MP3 player to the AUX In connector, and listen to it. To select auxiliary in to be played: 1. Press MENU. 2. Turn the TUNE knob to scroll to and highlight System Setup. Press the TUNE knob. 3. Turn the TUNE knob to scroll to and highlight AUX in. Press the TUNE knob. 4.
Configuring Your SIRIUS TTR1 Radio Alarms Before setting any alarms, refer to “Clock Setup” on page 53 and ensure that the clock is set correctly, i.e., the Time Zone and Daylight Savings Time are set correctly for your location. Then refer to “Alarm Clock” on page 32 for information about the alarm clocks. Refer to “Snooze” on page 34 for more information about the snooze function. Brightness Brightness has four settings to set the brightness of the display screen, Automatic, High, Medium, and Low.
Clock Setup Clock Setup allows you to change the clock settings: • Set Time/Date - Change the time and/ or date. • Auto Update - Synchronize the clock via the Internet Yes or No. Yes is the default and preferred setting. The radio will automatically update the time, keeping it accurate. Clock Setup Set Time/Date Auto Update Time Zone Daylight savings > • Time Zone - Select the time zone you are in. • Daylight savings - Turn daylight savings time On or Off. To set the time and date: 1. Press MENU. 2.
Configuring Your SIRIUS TTR1 Radio you have finished. To set Auto Update: 1. Press MENU. 2. Turn the TUNE knob to scroll to and highlight System Setup. Press the TUNE knob. 3. Turn the TUNE knob to scroll to and highlight Clock Setup. Press the TUNE knob. 4. Turn the TUNE knob to scroll to and highlight Auto Update. Press the TUNE knob. 5. Turn the TUNE knob to select either YES Auto Update Sync. Time Via Internet? YES* NO or NO, and press the TUNE knob. 6. Press MENU to exit.
4. Turn the TUNE knob to scroll to and highlight Time Zone. Press the TUNE knob. Time Zone Eastern 5. Turn the TUNE knob to scroll to and highlight the time zone you > are in. Press the TUNE knob. 6. Press MENU to exit. Central Mountain Pacific Alaska To set daylight savings time: 1. Press MENU. 2. Turn the TUNE knob to scroll to and highlight System Setup. Press the TUNE knob. 3. Turn the TUNE knob to scroll to and highlight Clock Setup. Press the TUNE knob. Daylight savings Daylight savings 4.
Configuring Your SIRIUS TTR1 Radio Network Network allows you to view and change the network settings: • Network wizard - Helps you to easily connect to a network • View settings - Displays information about your network connection • Manual Settings - Allows you to manually setup your connection to a network Network settings Network wizard View settings Manual Settings Network profile > • Network profile - Displays the wireless network connections saved in the radio Each Network menu option is discussed
• For connecting to a wireless network, refer to “To connect to a wireless network using the Network Wizard” on page 18. • For connecting to a wired network, refer to “To connect to a wired network using the Network Wizard:” on page 21. View settings: View Settings displays information about your network connection, including the type of connection, the status, the radio’s MAC address, and other network connection details such as IP addresses. To view the network settings: 1. Press MENU. 2.
Configuring Your SIRIUS TTR1 Radio Manual Settings: Refer to one the following sections for detailed instructions on using the Manual Settings to connect to a network: • For connecting to a wireless network, refer to “Connect to a Wireless Network Using Manual Settings” on page 66. • For connecting to a wired network, refer to “Connect to a Wired Network Using Manual Settings” on page 71.
3. Turn the TUNE knob to scroll to and highlight Network. Press the TUNE knob. 4. Turn the TUNE knob to scroll to and highlight Network profile. Press the TUNE knob. 5. The saved wireless network names will be displayed. If you wish to delete a profile, turn the TUNE knob to scroll to and highlight a profile name. Press the TUNE knob. 6. Confirm that you really want to delete the profile. Turn the TUNE knob to highlight YES or NO and press the TUNE knob. Confirm delete Confirm delete YES NO* 7.
Configuring Your SIRIUS TTR1 Radio Factory reset Factory reset restores the SIRIUS TTR1 Radio to the factory settings. It will erase all the stored network settings, account user name and password, favorite channels, alarm clock settings, lock code, and set all other options back to the factory settings. To restore the radio to the factory settings: 1. Press MENU. 2. Turn the TUNE knob to scroll to and highlight System Setup. Press the TUNE knob. 3.
Software update Software update allows you to set the radio to automatically check for any available software updates, and also to manually Software update force the radio to check if an update is available. Auto-check setting SIRIUS occasionally updates the software for Check now their radios. Check www.sirius.com for any updated documentation associated with a software update. By default, the SIRIUS TTR1 Radio is set to automatically check for updates.
Configuring Your SIRIUS TTR1 Radio want the radio to check for software updates. Turn the TUNE knob to highlight YES or NO and press the TUNE knob. 6. Press MENU to exit. To force the radio to check for a software update: 1. Press MENU. 2. Turn the TUNE knob to scroll to and highlight System Setup. Press the TUNE knob. 3. Turn the TUNE knob to scroll to and highlight Software Update. Press the TUNE knob. Software update Checking for new versions.../ 4.
Updating the software: If you manually force the radio to check for a software update, or the radio automatically finds a software update, and you want to update the software, follow these steps. 1. The Software update screen is displayed. Turn the TUNE knob to highlight YES and press the TUNE knob. 2. The radio will download the software update. Allow the download to finish. Software update New version available. Update Software? YES NO* 3.
Configuring Your SIRIUS TTR1 Radio 5. When the update is complete, you’ll be prompted to Press OK/Tune to start. Press the TUNE knob. 6. The radio will start with the new software. Software update Update Completed Press OK/Tune to start Info Info displays the software version number, and the Radio ID number. To display the information: 1. Press MENU. 2. Turn the TUNE knob to scroll to and highlight System Setup. Press the TUNE knob. 3. Turn the TUNE knob to scroll to and highlight Info.
Appendix: Manual Network Configuration 65
Appendix: Manual Network Configuration Connecting to a network using the Manual settings requires some knowledge of your network. You’ll need to manually configure your network connection using the Manual Settings or [Manual config] option if your wireless network name (SSID) is hidden, or if your network is DHCP disabled. Decide whether you will be using a wireless network connection (page 66), or a wired Ethernet connection (page 71). Then follow the instructions in the appropriate following section.
a. If you have just turned your SIRIUS TTR1 Radio on for the first time, the SSID screen will already be displayed. Skip ahead to step d. b. Press MENU and turn the TUNE knob to highlight System Setup. Press the TUNE Knob. c. Turn the TUNE knob to highlight Network. Press the TUNE Knob. d. Turn the TUNE Knob to highlight Manual Settings or [Manual config]. Press the TUNE Knob. e. Turn the TUNE Knob to highlight Wireless. Press the TUNE Knob. f.
Appendix: Manual Network Configuration iii. Enter the Gateway IP address for the network. iv. Enter the Primary DNS IP address for the network. v. Enter the Secondary DNS IP address for the network, or leave blank if there is none. h. Enter your wireless network name (SSID). IP settings IP address 0 . 0 . 0 . 0 Subnet mask 255 . 255 . 255 . 0 Key: 3/9 9/9 Note that the SSID is case sensitive. Turn 0123456789.
disabled. Turn the TUNE Knob to highlight your selection and press the TUNE knob. ii. Enter your key (password). Turn the TUNE knob to scroll through the list of characters and highlight each character. Press the TUNE knob to select the highlighted character and move to the next character. If you make a mistake, turn the TUNE knob to highlight BKSP and press the TUNE knob erase the character. • WPA or WPA2: i. Select whether WPA or WPA2 has TKIP or AES encryption.
Appendix: Manual Network Configuration to connect to your wireless network, the Connected screen will be displayed. If not, the Failed to connect screen is displayed. This means that one or more of the settings you entered is incorrect. l. If you are installing your SIRIUS TTR1 Radio for the first time, continue with “Step 2: Enter Your SIRIUS Account Information” on page 23.
Connect to a Wired Network Using Manual Settings In order to connect to a wired network, you will need to have the following information to enter during the procedure: Is DHCP enabled or disabled? If disabled, the IP address to use for the radio? If disabled, the Subnet Mask IP address? If disabled, the Gateway IP address? If disabled, the Primary DNS IP address? If disabled, the Secondary DNS IP address? a.
Appendix: Manual Network Configuration g. Turn the TUNE Knob to highlight Wired. Press the TUNE Knob. h. Will you be using DHCP? Turn the TUNE Connection type Wired Wireless 1/9 > > Knob to highlight DHCP enable or DHCP disable and press the TUNE Knob. i. If you have selected DHCP disable, enter the following information. Otherwise, continue with step j. For each entry, Turn the TUNE knob to select the numbers, and press the TUNE knob to confirm and move to the next number.
more of the settings you entered is incorrect. If Waiting for Ethernet is displayed, check the Ethernet cable connections. Connected k. If you are installing your SIRIUS TTR1 Radio for the first time, continue with “Step 2: Enter Your SIRIUS Account Information” on page 23. If you have previously entered your SIRIUS user name and key into the radio, and had tuned to a channel, the screen will show Connecting. When successfully connected, the Buffering...
Troubleshooting 75
Troubleshooting Your SIRIUS TTR1 Radio has been designed and built to be trouble-free but if you experience a problem, here’s some troubleshooting hints. You can also call SIRIUS Customer Care at 800-869-5964. If you see this on the screen: Try this: Connecting • The radio is attempting to connect to the SIRIUS Internet Radio service. If this message is displayed more than one minute, make sure your network is connected to the Internet.
If you see this on the screen: Try this: Waiting for Ethernet • The radio is expecting a wired Ethernet connection. Plug an Ethernet wire into your home network, then plug the other end into the Ethernet connection inside the compartment at the rear of the radio. (Refer to page 11 for the location of the connector.) • Change to a wireless network connection if a wired Ethernet connection is not available.
Troubleshooting 78 If you see this on the screen: Try this: Failed to connect • The network information you entered is incorrect. Verify and re-enter the information. (Refer to page 17 for a wireless network, or page 21 for a wired network.) • You have entered an incorrect password for a secure wireless network. Verify and re-enter the information. (Refer to page 23.) • If you have manually configured a network connection, you have entered one or more incorrect settings.
If this happens: Try this: The Network Wizard fails before the radio connects to your network • Your network has DHCP disabled. You’ll have to manually configure your network connection. (Refer to page 66 for a wireless network, or page 71 for a wired network.) The Network Wizard does not find your wireless network • Your wireless network has a hidden name (SSID).
Product Specifications 81
Product Specifications Dimensions SIRIUS TTR1 Radio 283 mm (W) x 185 mm (H) x 95 mm (D) 11 in (W) X 7.25 in (H) X 3.75 in (D) Remote 52 mm (W) x 85 mm (H) x 5 mm (D) 2 in (W) x 3.3 in (H) x .25 in (D) Weight SIRIUS TTR1 Radio 2.85 kg (6.3 lbs) Audio Outputs Headphone Line Out 3.5 mm diameter mini stereo jack 3.5 mm diameter mini stereo jack Audio Input Aux In 82 3.
Patent and Environmental Information Patent Information It is prohibited to, and you agree that you will not, copy, decompile, disassemble, reverse engineer, hack, manipulate, or otherwise access and/ or make available any technology incorporated in this product. Furthermore, the AMBE® voice compression software included in this product is protected by intellectual property rights including patent rights, copyrights, and trade secrets of Digital Voice Systems, Inc.
FCC Statement The user is cautioned that changes or modifications not expressly approved by SIRIUS XM Radio Inc. can void the user’s authority to operate this device. This device complies with Part 15 of the FCC Rules: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
Copyrights and Trademarks ©2009 SIRIUS XM Radio Inc. SIRIUS, XM and all related marks and logos are trademarks of SIRIUS XM Radio Inc. and its subsidiaries. All other marks and logos are the property of their respective owners. All rights reserved. Hardware, subscription and activation fee required. Other fees and taxes will apply. Month-tomonth subscriptions must be activated via telephone. Hardware and subscription sold separately. Subscription governed by SIRIUS Terms & Conditions available at sirius.
sirius.com SIRIUS XM Radio Inc. 1221 Avenue of the Americas New York, NY 10020 1.800.869.5364 © 2009 SIRIUS XM Radio Inc.