Installation Guide

ManualsBrandsSirius ManualsCooking Accessories125-150mm Tiled Roof Ducting Kit

SIRIUS Through Roof EasyKITs – “EASYROOF150T/M” and

“EASYROOF200T/M”

Sirius ducting kits are a high quality and simple, complete solution in a box. They provide an

ideal ventilation path to efficiently exhaust your kitchen fumes, steam, heat and odours –

filtered through your rangehood to the outside atmosphere.

There are 2 ducting sizes available – 150mm and 200mm. Please choose the correct size for

your rangehood and also that you specify for either a tiled or metal roof.

Please check that there is a clear

path for your ducting to run prior to installation, making sure

to look out for TV, computer, telephone and electrical cables, water and gas pipes, insulation

materials and air conditioning pipes and duct, before cutting holes.

For new homes, ideally fit the basic ducting (pipe) components at the frame up stage.

Additional lengths of ducting, joins, galvanised steel angled elbows and all other ducting

access

ories are available

SIRIUS EasyKIT.

from your local retailer, or Sirius online where you purchased your

For further advice please call our ducting consultation service on Ph: 1300 762 219 (Australia

only) or visit www.siriusbrand.com

and fill in the fields and one of our trained consultants will

assist you in the best manner possible.

Each EasyKIT comes complete with the following components, ready to be installed by a

suitably qualified and licensed tradesperson.

• 1 x 3m of Semi-Rigid PLUS aluminium ducting (SRPRO30/150 or SRPRO30/200)

• 1 x 1m of solid galvanised steel pipe (GP12-150 or GP12-200).

• 1 x *Silicone and soft form Aluminium roof flashing for either a tiled or metal roof.

• 1 x galvanised steel roof cowl (GRC-150 or GRC-200)

Tiled roof (TRFG075), Metal roof (MRF-G102)

• 1.5m galvanised steel, perforated bracing strap (GBS-200).

• 2 x galvanised steel duct connectors with double EPDM gasket seals (GDC150-GDC200).

• 2 x stainless steel ring clamps.

# Please note: We don’t supply silastic sealants, self-sealing fasteners (roofing screws), nails or wood screws for the bracing

strap… as most qualified trades people have these on board and will use whatever is appropriate for your buildings materials.

Installation Guide

(Disclaimer) The following instructions are provided as a guide only and in no way constitute or replace your local council requirements or Australian and New Zealand Standards and Building Codes.

1. Remove the required roofing tiles or cut the appropriate sized hole through the metal roof, being careful to watch out for insulation, cables, etc. (as above)

2. Using sharp tin snips, carefully trim the silicone cone to the correct pipe diameter. Wet the pipe with a water sp

ray as a lubricant and carefully fit over the

Summary of content (3 pages)

PAGE 1
SIRIUS Through Roof EasyKITs – “EASYROOF150T/M” and “EASYROOF200T/M” Professional Ducting Range Sirius ducting kits are a high quality and simple, complete solution in a box. They provide an ideal ventilation path to efficiently exhaust your kitchen fumes, steam, heat and odours – filtered through your rangehood to the outside atmosphere. There are 2 ducting sizes available – 150mm and 200mm. Please choose the correct size for your rangehood and also that you specify for either a tiled or metal roof.
PAGE 2
3. Fit the 2 gasketed duct connectors into each end of the galvanised pipe (1 top & 1 bottom). Ensure that the connectors are pushed firmly into the pipe, up to the centre rib of the connector. 4. The roof cowl can also be fitted at this stage, sliding the neck of the cowl over the duct connector fitted in the top end of the pipe. Again ensuring that it is pushed firmly on over the gaskets and down to the centre rib. 5.
PAGE 3
Tiled Roof: carefully place the top edge of the soft form aluminium base under the upper row of tiles… making sure to form up an anti-capillary fold. Then form up the left and right hand edges of the base, down neatly over the high edge of the profile of the side tiles. Neatly cut corner tabs and turn them under the tiles at the bottom edge of the base. To finish… trim the base to fit or as required to help fit neatly in with the size and profile of the tiles.