COMMERCIAL INFORMATION FOR THE CONSUMER GB INSTALLATION, USE AND MAINTENANCE INSTRUCTION SEM1 - SEM2 - SEM5 - SEM7 - SEM8 TECHNICAL INFORMATION TYPE: FSED
GB The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
GB Warnings! The air outlet of the appliance must not be connected to a flue which is used for exhausting other fumes from appliances, such as a central heating, boilers etc.. For the external exhausting of the fumes, comply with the regulations in force. Ventilate the room suitably according to the laws in force when the appliance is working together with gas, oil or coal burning appliances, at the same time. The motor of the peripheral exhausting group is powered by the cooker-hood placed in the kitchen.
SEM 1 (dis.1) - SEM 8 (dis.1a) Warning! The peripheral exhausting group (remote fitted extraction motor) is built in class II (symbol on the rating plate), therefore it must not be earthed. The appliance is designed to exhaust fumes and odours very silently and in the best way. It must be installed in the house and connected to the cooker-hood, which is in the kitchen (fig.
SEM 2 (fig.9) Warning! The remote fitted exhausting group (external motor) is built in class I plate, therefore it needs the earth connection. The appliance was designed to exhaust odours and vapours in the best way. The appliance is to be installed on the outside wall of the house and connetted to the cooker-hood which is in the kitchen (fig. 10) Installation: the mounting of the appliance is to be made by qualified technicians. Using the appropriate drilling jig (fig.
SEM 5 (fig.21) Warning! The remote fitted exhausting group (external motor) is built in class II (see symbol on the rating plate), therefore it must not be earthed. This model has been specifically studied to suction vapours and odours without noise.It should be installed outside and connected to the hood in the kitchen (fig. 22). Roof installation: make a 22 x 22 cm square opening on the roof, and then insert the lower part of the remote fitted exhausting motor (fig. 23).
SEM 7 (dis. 27) Warning! The remote fitted exhausting group (external motor) is built in class I plate, therefore it needs the earth connection. The appliance was designed to exhaust odors and vapors in the best way. The appliance is to be installed on the outside wall of the house and connected to the cooker-hood which is in the kitchen (fig. 28) Installation: the mounting of the appliance is to be made by qualified technicians. Using the appropriate drilling jig (fig.
WIRING DIAGRAM SEM1 - SEM5 9
WIRING DIAGRAM SEM2 10
WIRING DIAGRAM SEM7 11
WIRING DIAGRAM SEM8 12
SEM 1 SEM1 M 1 SEM 1 OK 1 1 2 OK 1 1a 2 SEM 1 3 1 24 3 4 6 4 3 2 3 5 4 5 5 5 13 7
5 4 5 7 6 7 6 7 8 19 19 8 14
OK OK OK SEM2 SEM 2 SEM 2 SEM 2 9 SEM 2 9 9 9 9 11 11 11 10 11 10 10 10 10 12 12 12 12 12 11 13 13 10 12 13 13 13 14 14 14 20 15 20
OK OK SEM5 SEM SEM5 5 SEM SEM 55 OK SEM 5 SEM 5 2222 22 22 22 22 2121 21 21 2121 22 21 242424 24 24 24 2323 23 23 23 23 24 23 25 2525 25 25 25 25 26 2626 26 26 26 26 22 16 22 22 22
SEM7 27 28 30 29 17
9004200486 - GM 04/12
