Operating Instructions
Table Of Contents
- Table of contents
- 1 Dear Customer,
- 2 General data
- 3 General description
- 4 Safety
- 5 Installation and startup
- 5.1 Transport and unpacking
- 5.2 Disposal of packaging materials
- 5.3 Installation site
- 5.4 Commissioning
- 5.4.1 Functional elements
- 5.4.2 Supplied tools
- 5.4.3 Touch display description
- 5.4.4 Illumination of the processing chamber, LED light strip, and On/Off button
- 5.4.5 Using the processing chamber screen
- 5.4.6 Installation
- 5.4.6.1 Connecting to the PC via LAN
- 5.4.6.2 Connecting the unit to the power supply
- 5.4.6.3 Installing the unit
- 5.4.6.4 Connecting the suction device (optional)
- 5.4.6.5 Connecting to the PC via WLAN (option)
- 5.4.6.6 Operating several production units at one access point
- 5.4.6.7 Connecting to the PC via the wireless interface (optional)
- 5.4.7 Filling the water tank
- 5.4.8 Switching the unit ON and OFF
- 5.5 Repacking
- 5.6 Scope of supply
- 5.7 Storage
- 6 Operation
- 7 Service
- 7.1 Using the cleaning hose and the wet cleaning process
- 7.2 Changing filter bags and HEPA filters
- 7.3 Changing the water
- 7.4 Instruments
- 7.5 Care, cleaning agents, and disinfectants
- 7.6 Cleaning surfaces
- 7.7 Replacing the main fuses
- 7.8 Changing the filter
- 7.9 Removing water from the unit
- 7.10 Using the tank cap opener
- 8 Technical description
- 9 Disposal
- 10 Consumable
- Index
5 Installation and startup
5.4 Commissioning
Dentsply Sirona
Operating Instructions CEREC Primemill
30
67 19 756 D3439
D3439.201.01.01.0209.2019
5.4.6.3.2 Process steps that have to be performed on the acquisition unit or
the PC
Automatic unit search
ü The unit is connected to the PC via a LAN cable or via WLAN.
1.
Click the
"Configuration"
button in the system menu.
2.
Click on the
"Devices"
button.
3.
Click on the
"Scan for New Devices"
button.
Ä All units connected to the PC are recognized. In the case of
new units, you will be prompted to enter a name.
4.
Enter a name and a short designation for the new unit.
Ä The unit name, the designation, and the software version are
then shown on the touch display.
Manual unit search
ü The unit is connected to the PC via a LAN cable or via WLAN.
1.
Click the
"Configuration"
button in the system menu.
2.
Click on the
"Devices"
button.
3.
Click on the
"Add Device (Manual)"
button.
4.
Set the network.
5.
Enter the network address which appears on the
"IP address:"
display once the production unit has been switched on.
6.
Click on the
"Ok"
button.
Ä The software attempts to contact the device.
If the connection fails, check the connection. If necessary, ask a
qualified technician.
Remove the unit
ü If you no longer require a unit (e.g. a unit is replaced), you can
remove it.
ü The unit is not in operation.
1.
Click the
"Configuration"
button in the system menu.
2.
Click on the
"Devices"
button.
3.
Click on the unit that you wish to uninstall.
4.
Click on the
"Delete Device"
button.
Ä You will be asked if you would like to remove the unit.
5.
Click on the
"YES"
button.
Ä
The device is removed.