Operating Instructions
Table Of Contents
- Table of contents
- 1 Dear Customer,
- 2 General data
- 3 General description
- 4 Safety
- 5 Installation and startup
- 5.1 Transport and unpacking
- 5.2 Disposal of packaging materials
- 5.3 Installation site
- 5.4 Commissioning
- 5.4.1 Functional elements
- 5.4.2 Supplied tools
- 5.4.3 Touch display description
- 5.4.4 Illumination of the processing chamber, LED light strip, and On/Off button
- 5.4.5 Using the processing chamber screen
- 5.4.6 Installation
- 5.4.6.1 Connecting to the PC via LAN
- 5.4.6.2 Connecting the unit to the power supply
- 5.4.6.3 Installing the unit
- 5.4.6.4 Connecting the suction device (optional)
- 5.4.6.5 Connecting to the PC via WLAN (option)
- 5.4.6.6 Operating several production units at one access point
- 5.4.6.7 Connecting to the PC via the wireless interface (optional)
- 5.4.7 Filling the water tank
- 5.4.8 Switching the unit ON and OFF
- 5.5 Repacking
- 5.6 Scope of supply
- 5.7 Storage
- 6 Operation
- 7 Service
- 7.1 Using the cleaning hose and the wet cleaning process
- 7.2 Changing filter bags and HEPA filters
- 7.3 Changing the water
- 7.4 Instruments
- 7.5 Care, cleaning agents, and disinfectants
- 7.6 Cleaning surfaces
- 7.7 Replacing the main fuses
- 7.8 Changing the filter
- 7.9 Removing water from the unit
- 7.10 Using the tank cap opener
- 8 Technical description
- 9 Disposal
- 10 Consumable
- Index
5 Installation and startup
5.4 Commissioning
Dentsply Sirona
Operating Instructions CEREC Primemill
36
67 19 756 D3439
D3439.201.01.01.0209.2019
5.4.6.7.1 CEREC Radio Device
Creating a network
The supplied network devices have not as yet been part of a network.
To enable several networks from various operators to be created next to
one another or in the same area, new network devices must first form a
network. This is described in the following section.
To create a new network with several new network devices, perform the
following steps:
1.
Place all network devices in the same area.
2.
Switch all network devices on within one minute.
3.
After switching on the last network device, wait approx. one minute.
4.
Make sure that all network devices are connected, as indicated by
the green LED; see section "LED displays" in the "CEREC Radio
Device" operating instructions (REF 65 45 177).
All network devices now belong to a single network, which can be
operated as an independent network, and can communicate with one
another. The network created in this way is unique worldwide. In the
event of problems, see section "Network creation failures" in the
"CEREC Radio Device" operating instructions (REF 65 45 177).
Extending the network - adding a new network device
New network units can be added to an existing network. However, to
prevent any network unit from becoming part of the network, the user
must complete four simple but specific steps:
1.
Place the new network units next to a network unit belonging to the
network.
2.
Switch on the new network devices.
3.
Switch the existing network device off and on again within one
minute.
4.
After one minute the new network devices will become part of the
network.
IMPORTANT
A network with CEREC Radio Devices can include up to three
network devices. Larger networks are not possible.