Thank you for purchasing Card Printer S-1000 of SISS Technology Inc. This Manual and the products are protected by copyright law and patent law. This manual and the product can be copied, reproduced, translated into any languages in any form that can be read by certain electronic media or machines without prior written consent of SISS Technology Inc. SISS Technology Inc. is not liable for any error or technical inaccuracies That occurs if you are fixing your product following this manual.
1. Preparation 1.1 Name and function of the Front …………………………………………………………………………… 2 1.2 Name and function of the Rear …………………………………………………………………………… 3 1.3 Name and function of the LCD 2. ……………………………………………………………………… 4 Installing Ribbon Cartridge 1.4 Replacement method of color ribbon ……………….………………………………………………….
Users must operate the product after they have read the precautions very carefully and thoroughly. The symbols of precautions contain important contents and are specified to Warning and Caution. There is no responsibility of our company for any accidents and/or damages of products owing to the ignorance of precautions while using. A breach of this instruction may cause serious or Slight wound, and may bring on damages of product And property.
A breach of this instruction may cause serious or slight wound, and may bring on damages of product and property. In relation to Power ▪ Do not use damaged power cord, Plugs, and loose outlets. ▪ Do not pull out the cord or touch the plugs with wet hands. ▪ Do not bend the power cord excessively or damage it by pressing it with heavy item. ▪ Pull the wire out when there is thunder and lightning or being not used for a long time. ▪ Do not use multiple electric devices at one outlet simultaneously.
A breach of cautions may cause serious or slight wound, and May bring on damages of product and property. In relation to Installation ▪ Do not install in unstable places. ▪ Keep the product out of the direct rays of the sun. It may cause defect of the product. ▪ Do not install around air conditioner and radiator. It will cause performance degradation. In relation to maintenance ▪ Do not separate the cover or protection devices. ▪ Turn off the product in advance in case you put your hands inside of it.
Ⅶ Ribbon Clean Roller+ Ribbon Cartridge Power Cable S-1000 Card Printer Power Adapter (24V, 2.5A) USB Cable (for 2.0) Please install the Printer by insuring sufficient space and keep it out from unstable, humid, direct rays of the sun,and the place closed to air conditioner or heater.
Front ① Cover ② Ribbon Cartridge ⑪ TPH Head ⑨RF Tag ⑤Stacker(Rear) ⑤Hopper&Stacker ⑧Button ⑥ Display/LED ⑤Stacker(front) Power Adapter Jack
1 ⑩ ③ ④ No Name Description of Function 1 Cover ▪ Open the Cover of Printer when you replace the ribbon or remove Card Jam. 2 Ribbon Cartridge ▪ The place where Color/Black ribbon is installed. Put ribbon cartridge in gently then it is naturally fixed. 3 M/SHead(Option) You must be careful so as not to damage MS Head. 4 Color Sensor ▪ It detects the limits of the color ribbon.
① ② ③ ④ No Name Description of Function 1 Power Jack 2 Ethernet Port ▪ Administrator use. 3 USBPort(B type) ▪ USB port. This product support USB 2.0. . 4 USBPort(A type) ▪ Administrator use. 5 Serial Port ▪ Spare Serial Port. Adapter ▪ DC 24V (2.5A) is used. Using substandard Adapter may cause the breakdown of the device. Use the standard specification of Power for the product. Nonstandard power supply may cause malfunction and defect of the product.
② LEDs(RGB) Button OLED Display ② 1.3 inch OLED LED No Color 1 Green 2 Yellow 3 Red Status Description of Function ON. ▪ Printer Power ON-Ready OFF ▪ Printer Power OFF Twinkle. ▪ Data Sending / Receiving OFF ▪ Normal condition Twinkle ▪ Error occurs Cut of ribbon(In case of checking End Mark) Other errors occur Button No Button Description of Function 1 2 POWER FUNCTION ▪ One touch power on/Press 3 seconds, power off.
Used ribbon. Ribbon cartridge New ribbon.
FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.