Greyhound User Manual
Table of Contents Introduction ............................................................................................................ 3 Technical Specifications .............................................................................................. 4 Package Contents ..................................................................................................... 6 Cautions ................................................................................................................
Introduction Congratulations on your purchase of the Sitecom Greyhound AC2600 Wi-Fi Router. With a powerful 1.4 GHz Dual-Core Qualcomm® Internet Processor supporting combined Wi-Fi speeds of up to 2600 Mbps, the Sitecom Greyhound AC2600 Wi-Fi Router delivers smooth Ultra HD video streaming, lag-free online gaming and handles demanding tasks like no other.
Technical Specifications
* Theoretical wireless signal rate based on IEEE standard of 802.11a, b, g, n, ac chipset used. Actual throughput may vary. Network conditions and environmental factors lower actual throughput rate. All specifications are subject to change without notice.
Package Contents Open the package carefully, and make sure that none of the items listed below are missing. Do not discard the packing materials, in case of return; the unit must be shipped back in its original package.
Cautions This router’s design and manufacturer has your safety in mind. In order to safely and effectively use this router, please read the following before usage. Usage Cautions The user should not modify this router. The environmental temperature should be within +5 ~ +35 degrees Celsius. Power The router’s power voltage is DC 12V 3.3A. When using this router, please connect the supplied AC adapter or AC adapter cable to the router’s power jack.
Product Layout Port Description S/PDIF connector Connect an optical TOSLINK cable for audio output 3.5mm connector Connect a 3.
Backlabel and Network Details Folder The Network Details Folder describes the IP address, login details, network name, security code and OPS button functionality. Button Description OPS button Press for 2 seconds for WPS/OPS mode Reset button Press for 2 seconds or until the Greyhound logo on the front starts flashing.
LED Definition As shown from the top to the bottom. Port Description Power Shows the device is turned on. WAN Shows the WAN cable is connected. LAN Shows the cable is connected. LAN Shows the cable is connected. LAN Shows the cable is connected. LAN Shows the cable is connected. WPS Shows OPS activity. USB 1 Shows when a USB device is connected. USB 2 Shows when a USB device is connected. SD Shows when a SD card is inserted. 5GHz WiFi Shows 5GHz WiFi activity. 2.4GHz WiFi Shows 2.
Network and System Requirements To begin using the router, make sure you meet the following as minimum requirements: Network Requirements An Ethernet-based broadband modem Computer with the following: - Web-based Configuration - Windows®, Macintosh, or Linux-based operating system An installed Ethernet adapter or wireless adapter Supported Browsers: Internet Explorer 9 or higher Firefox Safari 4 or higher Chrome
Setup your Router You can place the router on a desk or other flat surface, or you can mount it on a wall. For optimal performance, place your router in the center of your home (or your office) in a location that is away from any potential source of interference, such as a metal wall or microwave oven. This location must be close to a power connection and your ADSL/Cable modem. Connect the supplied power-adapter to the power inlet port and connect it to a wall outlet.
Setup your Computer Windows, Manual Connection Click on the icon for wireless connectivity. This is usually located in the System Tray, next to the clock. Select the Sitecom network. The correct network name can be found on the sticker on bottom of the router, or in the Network Details Folder. Fill in the password for the wireless network. The correct password can be found on the sticker on the bottom of the router, or in the Network Details Folder.
Windows, OPS Connection Click on the icon for wireless connectivity. This is usually located in the System Tray, next to the clock. Select the Sitecom network. The correct network name can be found on the sticker on bottom of the router, or in the Network Details Folder. Push the OPS Button on the router. For 2.4GHz, press the 2.4GHz button. For 5GHz, press the 5GHz button. Wait for the icon to display that it’s connected to the network.
Mac OSX Click on the icon for wireless connectivity. This is usually located in the System Tray, next to the clock. Select the Sitecom network. The correct network name can be found on the sticker on bottom of the router, or in the Network Details Folder. Fill in the password for the wireless network. The correct password can be found on the sticker on the bottom of the router, or in the Network Details Folder. Wait for the icon to display that it’s connected to the network.
Login to your Router LOGIN procedure • OPEN your browser (e.g. Internet Explorer). • Type http://sitecom.router in the address bar and press [Enter]. Alternatively, type http://192.168.0.1 in the address bar and press [Enter] . You’ll see the following screen: • Type the password. The default username is already filled in; the password can be found on the back label on the bottom of your router or in the Network Details Flyer. Click Login. You will see the home page of the Greyhound Router.
Configure your Internet connection From the menu, select “Advanced Mode”. From the top menu, select “Interfaces” and then “WAN” for configuring IPv4 connections.
Depending on the chosen setting, you may need to enter your user name and password, MAC address or hostname in the following window. After you have entered the correct information, click Save & Apply.
IPv6 Configuration The IPv6 (Internet Protocol version 6) section is where you configure your IPv6 Connection type. From the top menu, select “Interfaces” and then “WAN6” for configuring IPv6 connections. IPv6 Connection Type There are several connection types to choose from: Static IPv6, Autoconfiguration, 6RD and Link-local only. If you are unsure of your connection method, please contact your IPv6 Internet Service Provider.
Configure your Router – Basic Mode This is the page you see when first logging in to the web interface. It contains easily accessible buttons that allow you to look at or modify the most commonly used features, laid out in a simple page.
Wi-Fi settings On this page you can see the network name (SSID) and password for both the 2.4GHz and 5GHz. By clicking the ‘Edit’ button you can enable or disable the Wi-Fi signal and security, change the network name and change the password. Click ‘Apply’ to save the modifications.
Guest Network Settings The Guest network is a separate network that only allows an internet connection. There is no interaction between devices connected on the Guest network, as well as between the Guest network and the regular Wi-Fi network. On this page you can see the network name (SSID) and password for both the 2.4GHz and 5GHz Guest network. By clicking the ‘Edit’ button you can enable or disable the Wi-Fi signal and security, change the network name and change the password.
OPS Activation On this page you can activate the OPS/WPS function of the router. By pushing either of the buttons, the router starts transmitting the WPS beacon. You can also activate the function by pushing the physical buttons on the router as described a couple of pages back. After clicking the button you can connect your client to the network without entering a password. The timeout is 2 minutes.
Storage USB/SD On this page you can activate the various functions for the USB and/or SD card connections that are present on the Greyhound router. ‘Storage Settings’ shows the devices that are connected to the USB and/or SD Card connections. By clicking the various options you can enable or disable the feature. Sharing : By selecting this feature you enable the SMB server. A network share will become visible in your home network and you can copy files from and to this share.
Print Server & AirPrint On this page you can enable or disable the Print Server function. You can connect a USB printer to one the USB ports on the Greyhound router. Doing this results in the printer becoming a network device, so every client device on the network can print to this printer. The Sitecom USB Control Center software is used for this, which is described further down in this manual. AirPrint is a feature used on Apple Mac OSX and Apple iOS devices.
Audio / Music Player On this page you can configure the built-in audio stream functionality. The Greyhound supports both Apple AirPlay and DLNA. After enabling the feature, you can assign a device name. This is the name that will be shown in the list of available output devices on an AirPlay/DLNA compatible player. You can also choose between the S/PDIF and 3.5mm jack output on the back of the router. Both outputs cannot be active at the same time. Click ‘Apply’ to save the settings.
StreamBoost Technology On this page you can modify the StreamBoost settings. StreamBoost is automatic network bandwidth management / traffic shaping technology. It intelligently manages network bandwidth and latency, giving each application the bandwidth it needs for the best possible user experience. When the page is opened for the first time, StreamBoost tries to detect the speed of the internet connection by running a speedtest.
Firmware update On this page you can view the current firmware version that’s installed in the router. It will also show the available version on our update server. The ‘View Changelog’ button shows the changes that have been made in the firmware version that’s available on our update server. The ‘Check for new firmware’ button allows the router to check on the update server for a new firmware version.
Configure your Router – Advanced Mode By clicking the ‘Advanced Mode’ button you’ll enter this mode. The Advanced Mode allows for a more extensive configuration of the various features of the router. Home The System status section allows you to monitor the current status of your router, the UP time, hardware information and serial number as well as firmware version information is displayed here.
Wi-Fi Settings You can set parameters that are used for the wireless stations to connect to this router for the 2.4 GHz radio or 5 GHz radio. The parameters include Mode, ESSID, Channel Number and Associated Client, amongst others. Wi-Fi Overview On this page you can enable or disable the Wireless radios separately, including the Guest network. By clicking the Edit button you enter the settings page.
Wi-Fi settings – Device Configuration • • • • • • • • • • Green Mode: This mode dynamically adjusts the system's Wi-Fi transmit power depending on the distance between the router and the client device. Band Steering: Band steering is a technology that detects whether or not the wireless client is dual-band capable, and if it is, it will push the client to connect to the less congested 5GHz network. Please note that the 2.4GHz and 5GHz SSID’s need to be identical for this feature to work.
• • • DTIM Period: DTIM stands for Delivery traffic indication map or message and is an additional message added after the normal beacon broadcast by your router or access point. Depending on the timing set for your router, the router “buffers” broadcast and multicast data and lets clients know when to “wake up” to receive those data. Preamble Type: The “Long Preamble” can provide better wireless LAN compatibility while the “Short Preamble” can provide better wireless LAN performance.
Wi-Fi settings – Interface Configuration • • • ESSID: This is the name of the wireless signal which is broadcasted. All the devices in the same wireless LAN should have the same SSID. Hide ESSID: Hides the network name (SSID) from being broadcast publicly. Separate Clients: Prevents client-to-client communication on this network. Security This router provides complete wireless LAN security functions, included are WEP, IEEE 802.11x, IEEE 802.11x with WEP, WPA with pre-shared key and WPA with RADIUS.
Disable When you choose to disable encryption, it is very insecure to use the router. WEP When you select 64-bit or 128-bit WEP key, you have to enter WEP keys to encrypt data. You can generate the key by yourself and enter it. You can enter four WEP keys and select one of them as a default key. Then the router can receive any packets encrypted by one of the four keys.
Group Key Update Interval: Enter the amount of time before the group key used for broadcast and multicast data is changed (3600 is default). Passphrase: Enter a Wi-Fi password (key/passphrase). The password must be between 863 characters. WPA-/WPA2-/WPA Mixed-Enterprise Wi-Fi Protected Access (WPA) is an advanced security standard. You can use an external RADIUS server to authenticate wireless stations and provide the session key to encrypt data during communication.
MAC Filter This wireless router supports MAC Address Control, which prevents unauthorized clients from accessing your wireless network. • • • Enable wireless access control: Enables the wireless access control function. You can choose between ‘Allow listed only’ or ‘Allow all except listed’. Adding an address into the list: Select the client to be added from the list and then click "Save & Apply". You can add more clients by pressing the + sign.
Wi-Fi - Guest Network Guest Network Access provides secure Wi-Fi access for guests to share your home or office network. When you have visitors in your house, apartment, or workplace, you can enable the guest network for them. You can set different access options for Guest Network users, which is very effective to ensure the security and privacy of your main network. • • • • • • ESSID: This is the name of the wireless signal which is broadcasted as the Guest Network.
WiFi – OPS One Push Setup (OPS) is the simplest way to establish a connection between the wireless clients and the wireless router. You don’t have to select the encryption mode and fill in a long encryption passphrase every time when you try to setup a wireless connection. You only need to press a button on both wireless client and wireless router, and OPS will do the rest for you. The wireless router supports two types of OPS: OPS via Push Button and OPS via PIN code.
• OPS via PIN: You can fill-in the PIN code of the wireless device and press the button to start the OPS process. The router will wait for the OPS/WPS request from the wireless device within 2 minutes.
Interface Settings Interfaces – Overview On this page you can see the various wired connections of your router. You can also connect and disconnect the WAN port to troubleshoot your internet connection. By clicking ‘Edit’ you’ll enter the settings page.
Interfaces - LAN The LAN tab gives you the opportunity to change the IP settings of the router. Click Save & Apply at the bottom of this screen to save any changes. • • • • • • IPv4 address 192.168.0.1: It is the router’s LAN IP address (Your LAN clients default gateway IP address). IPv4 netmask 255.255.255.0: Specify a Subnet Mask for your LAN segment. DHCP Server: Enabled by default. You can enable or disable the DHCP server.
Static DHCP IP If you want a client to always have the same IP address assigned, you can create a DHCP reservation. The router will assign the IP address only to that client. This IP address must be within the DHCP IP Address Range specified above, under DHCP Server. Click the + sign to add a client to the list. IP Address: Enter the IP Address you want to assign to the client. This IP Address must be within the DHCP IP Address Range. MAC address: Enter the MAC Address of the client.
Interfaces – WAN Depending on the chosen setting, you may need to enter your user name and password, MAC address or hostname in the following window. After you have entered the correct information, click Save & Apply.
Interfaces – WAN6 IPv6 Connection Type There are several connection types to choose from: Static IPv6, Autoconfiguration, 6RD and Link-local only. If you are unsure of your connection method, please contact your IPv6 Internet Service Provider. Static IPv6 Mode This mode is used when your ISP provides you with a set IPv6 addresses that does not change. The IPv6 information is manually entered in your IPv6 configuration settings.
Interfaces – Switch A VLAN is a switched network that is logically segmented by function, project team, or application, without regard to the physical locations of the users. VLANs have the same attributes as physical LANs, but you can group end stations even if they are not physically located on the same LAN segment. Any switch module port can belong to a VLAN, and unicast, broadcast, and multicast packets are forwarded and flooded only to end stations in the VLAN.
Interfaces – Routes Static routing is a form of routing that occurs when a router uses a manually-configured routing entry, rather than information from a dynamic routing traffic. Unlike dynamic routing, static routes are fixed and do not change if the network is changed or reconfigured. Destination LAN IP: The IP address of the network to include in the routing table. Subnet Mask: The subnet mask for this destination. If the destination is a single host, type 255.255.255.
StreamBoost StreamBoost is automatic network bandwidth management / traffic shaping technology. It intelligently manages network bandwidth and latency, giving each application the bandwidth it needs for the best possible user experience. StreamBoost – Priorities You can select the priority of each device on your local network. The priority control buttons are the arrows within the boxes to the left of each icon representing a device.
StreamBoost – Up Time Here you can view the Active Time (in minutes) and see what applications are being used. You can select the time frame from the drop-down menu. Choose from last month, last week, or last day.
StreamBoost – Downloads Here you can view the type of traffic that is mostly used on your network, including the consumed bandwidth.
StreamBoost – Consumption Per Device Here you can view the bandwidth consumption per device. You can click on the device to highlight it. You can select the time frame from the drop-down menu.
StreamBoost – Consumption per Flow Here you can view the bandwidth consumption per traffic type. You can click on traffic type to highlight it. You can select the time frame from the drop-down menu.
File System Settings File Systems – Mount Points On this page you will find all the storage points that the OpenWRT operating system uses. Under the ‘Mount Points’ section you’ll find the attached USB storage devices.
File Systems – FTP On this page you can configure the users that have access to the FTP server. The default admin user already has access. Add User: Click here to add a new user. You can enter a username and a password and choose to assign ‘Read’, ‘Read/Write’, ‘Read/Delete’ or ‘All’ rights to the files and folders on the storage device attached to the router. Edit User: Click on the radio button in front of the user you want to edit and click the button.
File Systems – Network Shares On this page you can edit the settings for the SMB server. Server name: Enter a name for the network share. Workgroup: If you wish to add the share to your workgroup enter the workgroup name here. Description: Enter a desired description for the share. Administrator: Enter a desired username for access to the share.
File Systems – Transmission On this page you can edit the settings for the Bittorrent client Transmission. Transmission has its own web interface that can be opened via the ‘Open Web Interface’ button. Preallocation: Whether to fill the space for chunks not yet downloaded with "0" (helps avoiding fragmentation). DHT enabled: Whether to enable dht (distributed hash tables). Encryption: Whether to use encrypted connections only. uTP enabled: Whether or not to enable the Micro Transport Protocol.
Peer port: The fixed port transmission listens to incoming connections. Alternative speed enabled: Whether transmission should use two speed limit settings. RPC authentication required: Whether transmission-daemon should be remote controlled by a GUI on a host machine.
App Settings This page allows you to install OpenWRT packages. With this unique feature you can easily add or remove functionality to your router, just like installing and uninstalling applications on your computer. For more information on this, please go to https://wiki.openwrt.org/doc/packages. You can add packages by typing in the URL into the ‘Download and install package’ field. You can remove packages by selecting it from the list of ‘Installed Packages’ and clicking the – button.
Firewall Settings Firewall – Enable The router provides extensive firewall protection by restricting connection parameters, thus limiting the risk of hacker attacks, and defending against a wide array of common Internet attacks. However, for applications that require unrestricted access to the Internet, you can configure a specific client/server as a Demilitarized Zone (DMZ). Note: To enable the Firewall settings select Enable and click Save & Apply.
Firewall – DMZ If you have a client PC that cannot run an Internet application (e.g. Games) properly from behind the NAT firewall, then you can open up the firewall restrictions to unrestricted two-way Internet access by defining a DMZ Host. The DMZ function allows you to re-direct all packets going to your WAN port IP address to a particular IP address in your LAN.
Firewall – DoS The Broadband router's firewall can block common hacker attacks, including Denial of Service, Ping of Death, Port Scan and Sync Flood. If Internet attacks occur the router can log the events. Ping of Death: Protection from Ping of Death attacks Discard Ping From WAN: The router’s WAN port will not respond to any Ping requests Port Scan: Protects the router from Port Scans. Sync Flood: Protects the router from Sync Flood attack.
Firewall – Access You can restrict users from accessing certain Internet applications/services (e.g. Internet websites, email, FTP etc.). Access Control allows users to define the traffic type permitted in your LAN. You can control which PC client can have access to these services. Deny: If you select “Deny” then all clients will be allowed to access Internet accept for the clients in the list below.
Firewall – URL block You can block access to some Web sites from particular PCs by entering a full URL address or just keywords of the Web site. Enable: URL Blocking Enable/disable URL Blocking Add URL/keyword: Fill in “URL/Keyword” and then click “Add”. You can enter the full URL address or the keyword of the web site you want to block.
Firewall – Virtual Server Use the Virtual Server function when you want different servers/clients in your LAN to handle different service/Internet application type (e.g. Email, FTP, Web server etc.) from the Internet. Computers use numbers called port numbers to recognize a particular service/Internet application type. The Virtual Server allows you to re-direct a particular service port number (from the Internet/WAN Port) to a particular LAN private IP address and its service port number.
Firewall – ALG An application gateway is an application program that runs on the router. When a client program establishes a connection to a destination service, it connects to an application gateway, or proxy. The client then negotiates with the proxy server in order to communicate with the destination service.
Task manager System Logs On this page you can find the system log. If you’re using an external logging server you can enable the ‘Remote Log’ functionality and enter the IP Address of the server in the appropriate field.
Kernel log Here you can view the messages the kernel puts out. Processes Here you can see the running processes. There are 3 buttons to alter the functionality of the process. Hang up: This signal is used to report the termination of the controlling process on a terminal to jobs associated with that session; this termination effectively disconnects all processes in the session. Terminate: A generic signal used to cause program termination. It is the normal way to politely ask a program to terminate.
Kill: Used to cause immediate program termination. It cannot be handled or ignored, and is therefore always fatal. It is also not possible to block this signal. Realtime Load On this page you can view the actual load on the entire network. The page shows 3 graphs in 3 different colors.
Initscripts On this page you can see the scripts controlling the various functions of the router. There are 4 buttons available. Enable/Disable: You can choose whether you want the service to be automatically started during bootup. Start: Start the service. Restart: Restart the service. Stop: Stop the service.
Scheduled Tasks This window allows you to edit the crontab file. This contains the schedule of cron entries to be run at specified times. The commands that can be used are standard Unix commands.
Administration Administration – Time Zone The Time Zone allows your router to base its time on the settings configured here, which will affect functions such as Log entries and Firewall settings. You can choose to set the time manually or via a NTP server. NTP server: You can set an NTP server address. Set Time Zone: Select the time zone of the country you are currently in. The router will set its time based on your selection.
Administration – Administration You can change the password required to log into the router's system web-based management. Passwords can contain 0 to 12 alphanumeric characters, and are case sensitive. Administrator Username: By default this is ‘admin’. Current Password: Fill in the current password to allow changing to a new password. New Password: Enter your new password. Verify Password: Enter your new password again for verification purposes.
Administration – Backup/Flash Firmware Use the "Generate archive" button to save the current configuration to a file on your PC. You can then use the "Restore backup" button to restore the saved configuration to the router. Alternatively, you can use the "Reset to Factory Defaults” button to force the router to perform a power reset and restore the original factory settings. This page also allows you to upgrade the Broadband router’s system firmware.
Administration – SSH SSH is a cryptographic (encrypted) network protocol to allow remote login and other network services to operate securely over an unsecured network. Interface: Select the interface on which you want the SSH service to be active. Port: Select the port on which you want the SSH service to be active. Default is 22. SSH keys: Here you can paste public SSH-Keys (one per line) for SSH Public-key authentication.
Administration – LED Configuration On this page you can switch the LEDs on the router on or off. Power: This switches of the lighting behind the Greyhound logo. LAN: This switches of all 4 LAN LEDs. WLAN-2.4GHz: This switches off the 2.4GHz WLAN LED. WLAN-5GHz: This switches off the 5GHz WLAN LED.
Toolbox Settings Toolbox – DDNS DDNS allows you to map the static domain name to a dynamic IP address. You must get an account, password and your static domain name from the DDNS service providers. This router supports DynDNS, no-ip and other common DDNS service providers. Enable/Disable: Enable or disable the DDNS function of this router. Service: Select a DDNS service provider. Hostname: Fill in your static domain name that uses DDNS.
Toolbox – UPnP With UPnP, all PCs in your network will discover this router automatically, so you don’t have to configure your PC and it can easily access the Internet through this router. UPnP Feature: You can enable or Disable the UPnP feature here. After you enable the UPnP feature, all client systems that support UPnP, like Windows, can discover this router automatically and access the Internet through this router without having to configure anything.
Toolbox – Remote Access The remote management function allows you to designate a host in the Internet the ability to configure the Broadband router from a remote site. Enter the designated host IP Address in the Host IP Address field. Method: Choose between ‘All Hosts’ or ‘Specific Host’. If ‘All Hosts’ is chosen this means anyone can access the router’s web-based configuration from a remote location, providing they know the password.
Addendum A: NetUSB The netUSB functionality of your router requires additional software to work with your computer. The following section will describe how the software can be installed and used. Windows Insert the CD-ROM that was included with your router and select install utility from the cdmenu. The software will inform you about what will be installed. Click Next to continue the installation.
Enter your username and organization if applicable and click Next to continue. Choose a folder where the software should be installed or keep it to default and click Next to continue. The software is now ready to be installed, Click Install to continue.
Once the installation is finished the software will inform you. If “Launch Sitecom USB Device Server” checked the software will automatically be launched after you clicked Finish.
MacOS Insert the CD-ROM that was included with your router and select “Install” from the cd-menu. Click Install to continue installation. Enter your Mac username and password and click OK to continue. Once the installation is finished the software will inform you and requires to restart the system.
Connect & Disconnect “NetUSB” allows you to use USB printers when they’re actually connected to the Sitecom USB server. The “connect” operation is a software operation that simulates an actual USB device plug-in. Therefore, when you do a “connect” operation in the Control Center, the PC can detect a USB device’s plug-in, although actually you do not plug in any USB device to your PC. Similarly, the “disconnect” operation is a software operation that simulates the disconnection of the USB device.
NetUSB installation The steps to do installation for USB devices, like MFPs: Make sure the router is turned on. Connect the USB device to the USB port of the router. Run the Control Center. In the “USB MFP Server List” window, you can see the host names and IP addresses all of the Sitecom servers (in blue) on the network, as shown below. Click the server. Then all USB devices attached to the server will be shown. Please follow the user manual of the USB device to install its driver.
PC will automatically detect that the USB device is plugged-in. On the right side of the Windows Task Bar, you can see the information of the new device. Continue to follow the user manual of the USB device to do the rest jobs of installation, until the driver installation has finished. After the installation, you can see the newly created devices on the PC. If the USB device is a MFP, you can see a new printer and a new scanner from the “Control Panel”.
NetUSB Printing using Auto-Connect Printer After the driver is installed, you can see a newly created printer in the Control Panel. Follow the steps below to perform NetUSB printing. In the Control Center, click the MFP server that has the desired printer (or MFP) attached. Click the desired printer (or MFP). Click the “Auto Connect Printer” button and choose “Set Auto-Connect Printer”. The following figure will appear. Choose the desired printer.
Note: Under the “Auto-Connected Printer” setting, it is not necessary to manually press the “Connect” button when printing. If you press the “Connect” button for printing, please make sure to click “Disconnect” button after you finish the printing. Otherwise, other users cannot print properly. It is because you are the only ownership of the connected printer. AutoRun You can make the Control Center be run automatically after you login Windows.
NetUSB Scanning using Network Scanning In the Control Center, click the MFP server that has the desired MFP attached. Click the desired MFP. Click the “Network Scanner” button. Then you can see that the Control Center will automatically do a “connect” operation. The following window will appear. Choose one of TWAIN or WIA item. Click “OK”. The following window will appear.
Follow the usual steps to do scanning.
Addendum B: Declaration of Conformity
Addendum C: GNU/GPL Information Parts of the firmware of the Greyhound Wireless Broadband Router are subject to the GNU general public license. Licensing Information This product includes third-party software licensed under the terms of the GNU General Public License. You can modify or redistribute this free software under the terms of the GNU General Public License. Please see Appendix B for the exact terms and conditions of this license.
24 etherwake http://ftp.debian.org/debian/pool/main/e/etherwake 1.09 GPL V2 25 ethtool http://sourceforge.net/projects/gkernel/ 3.4.1 GPL V2 26 Expat http://expat.sourceforge.net/ 2.0.1 GPL V2 27 Fcgi http://www.fastcgi.com/dist/ 2.4.0 GPL V2 28 fdk-aac http://downloads.sourceforge.net/opencore-amr/ 0.1.1 GPL V2 29 ffmpeg http://ffmpeg.org/releases/ 1.0.1 GPL V2 30 file ftp://ftp.astron.com/pub/file/ 5.11 GPL V2 31 freetype http://www.freetype.org/ 2.4.
55 libgpg-error http://www.gnupg.org/related_software/libgpg-error/ 1.9 GPL V2 56 libid3tag http://sourceforge.net/projects/mad/files/libid3tag/ 0.15.1b GPL V2 57 libiwinfo https://dev.openwrt.org/browser/trunk/package/ 44 GPL V2 58 Libjpeg http://www.ijg.org/files/ 6b GPL V2 59 Libmad http://www.underbit.com/products/mad/ 0.15.1b GPL V2 60 libnetfilter_conntrack http://www.netfilter.org/projects/libnetfilter_conntrack/ 0.9.1 GPL V2 61 libnfnetlink http://netfilter.
87 mtd-utils http://processors.wiki.ti.com/index.php/MTD_Utilities 1.4.5 GPL V2 88 mysql http://dev.mysql.com/ 5.1.53 GPL V2 89 ncurses (terminfo) http://www.gnu.org/software/ncurses/ 5.7 GPL V2 90 netatalk http://netatalk.sourceforge.net 2.2.1 GPL 91 netifd git://nbd.name/luci2/netifd.git 2013/7/16 GPL V2 92 ngrep http://ngrep.sourceforge.net 1.45 BSD 93 ntfs-3g http://www.tuxera.com/community/ntfs-3g-download 2011.4.12 GPL V2 94 odhcp6c https://github.com/sbyx/odhcp6c.
119 Tc http://lartc.org/ 3.3.0 GPL V2 120 tftp-hpa http://www.kernel.org/pub/software/network/tftp 0.48 BSD 121 transmission http://www.transmissionbt.com 2.71 GPL V2 122 uboot http://www.denx.de/wiki/U-Boot 2012.07 GPL V2 123 uboot-envtools http://www.denx.de/wiki/U-Boot 2012.04.01 GPL V2 124 ubus git://nbd.name/luci2/ubus.git 2013-8-8 LGPLv2.1 125 uci git://nbd.name/uci.git 2013-6-11 LGPLv2.1 126 uclibc http://www.uclibc.org/downloads/ 0.9.33.
Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc. 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The licenses for most software are designed to take away your freedom to share and change it.
any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License.
Revision 1.0 © Sitecom Europe BV 2016 Note: All the information contained in this manual was correct at the time of publication. However, as our engineers are always updating and improving the product, your device’s software may have a slightly different appearance or modified functionality than presented in this manual.
