WLM-6600 User Manual
Table of Contents Introduction .......................................................................................................... 3 Key Features ......................................................................................................... 4 Package Contents .................................................................................................. 5 Cautions ...............................................................................................................
Introduction Congratulations on your purchase of the WLM-6600 Wireless ADSL2+ Modem. This modem is fully compliant with 802.11a, 802.11b, 802.11g and 802.11n. This modem provides the best performance when used in combination with 802.11n client adapters. The WLM-6600 is not only a Modem or Wireless Access Point, but can also be used to connect wired Ethernet devices at 10/100/1000 Mbit speeds.
Key Features Features Advantages Incredible Data Rate up to Heavy data payloads such as MPEG video 450Mbps* streaming IEEE 802.11n Compliant and Fully Interoperable with IEEE 802.11b / backwards compatible with IEEE802.11g compliant devices with 802.11b/g legacy protection Four 10/100/1000 Mbps Switch Ports (Auto-Crossover) Firewall supports Virtual Server Mapping, DMZ, IP Filter, ICMP Blocking, SPI Scalability, extend your network.
Package Contents Open the package carefully, and make sure that none of the items listed below are missing. Do not discard the packing materials, in case of return; the unit must be shipped back in its original package.
Cautions This router‟s design and manufacturer has your safety in mind. In order to safely and effectively use this router, please read the following before usage. Usage Cautions The user should not modify this router. The environmental temperature should be within +5 ~ +35 degrees Celsius. Power The router‟s power voltage is DC 12V 2A. When using this router, please connect the supplied AC adapter or AC adapter cable to the router‟s power jack.
Product Layout Port Description Power connector Connect the 12V DC adapter to this port USB Port (x2) Connect a USB device to this port LAN (Yellow) Connect your PCs or network devices to these ports ADSL (Grey) Connect your ADSL cable to this port Backlabel and Network Details Folder The Network Details Folder describes the IP address, login details, network name, security code and OPS button functionality.
LED Definition As shown from the top to the bottom. Port Description Power (Red) Shows the device is turned on. DSL (Green) Shows the DSL signal is synchronized. Internet (Blue) Shows the Internet connection is active. LAN (Blue) Shows the cable is connected. LAN (Blue) Shows the cable is connected. LAN (Blue) Shows the cable is connected. LAN (Blue) Shows the cable is connected. 2.4GHz (Blue) Shows 2.4GHz WiFi activity. 5GHz (Blue) Shows 5GHz WiFi activity.
Network + System Requirements To begin using the router, make sure you meet the following as minimum requirements: PC/Notebook. Operating System – Microsoft Windows XP/VISTA/7 or Mac OSX 1 Free Ethernet port. WiFi card/USB dongle (802.11 a/b/g/n) – optional. PC with a Web-Browser (Internet Explorer, Safari, Firefox, Opera) Ethernet compatible CAT5e cables.
Setup your Router You can place the router on a desk or other flat surface, or you can mount it on a wall. For optimal performance, place your router in the center of your home (or your office) in a location that is away from any potential source of interference, such as a metal wall or microwave oven. This location must be close to a power connection and your ADSL connection. Connect the supplied power-adapter to the power inlet port and connect it to a wall outlet.
Setup your Computer Windows, Manual Connection Click on the icon for wireless connectivity. This is usually located in the System Tray, next to the clock. Select the Sitecom network. The correct network name can be found on the sticker on bottom of the router, or in the Network Details Folder. Fill in the password for the wireless network. The correct password can be found on the sticker on the bottom of the router, or in the Network Details Folder.
Windows, OPS Connection Click on the icon for wireless connectivity. This is usually located in the System Tray, next to the clock. Select the Sitecom network. The correct network name can be found on the sticker on bottom of the router, or in the Network Details Folder. Push the OPS Button on the router. Keep the button pushed for 0-5 seconds. Wait for the icon to display that it‟s connected to the network.
Mac OSX Click on the icon for wireless connectivity. This is usually located in the System Tray, next to the clock. Select the Sitecom network. The correct network name can be found on the sticker on bottom of the router, or in the Network Details Folder. Fill in the password for the wireless network. The correct password can be found on the sticker on the bottom of the router, or in the Network Details Folder. Wait for the icon to display that it‟s connected to the network.
Login to your Router LOGIN procedure • OPEN your browser (e.g. Internet Explorer). • Type http://sitecom.modem or http://192.168.0.1 in the address bar and press [Enter]. • Type user name and password. The default username is admin, the password can be found on the back label on the bottom of your router. • • Click OK. You will see the home page of the WLM-6600.
Configure your Internet connection From the menu, select “Internet Settings”. Depending on the chosen setting, you may need to enter your user name and password, MAC address or hostname in the following window. After you have entered the correct information, click Apply.
IPv6 Configuration The IPv6 (Internet Protocol version 6) section is where you configure your IPv6 Connection type. IPv6 Connection Type There are several connection types to choose from: Static IPv6, Autoconfiguration, 6RD and Link-local only. If you are unsure of your connection method, please contact your IPv6 Internet Service Provider. Static IPv6 Mode This mode is used when your ISP provides you with a set IPv6 addresses that does not change.
6RD Mode In the 6RD mode, no additional configuration is necessary. Link-local Mode The Link-local address is used by nodes and routers when communicating with neighboring nodes on the same link. This mode enables IPv6-capable devices to communicate with each other on the LAN side.
Status The pages in the status section provide you general information about the operational status of your device. Status The System status section allows you to monitor the current status of your modem/router: the UP time, hardware information, serial number as well as firmware version information is displayed here. The page also shows extensive information concerning the ADSL status and current settings.
Statistics You can view statistics on the processing of IP packets on the networking interfaces. You will not typically need to view this data, but you may find it helpful when working with your ISP to diagnose network and Internet data transmission problems. To display statistics for any new data, click “Refresh”. DHCP List This page shows all DHCP clients (LAN PCs) currently connected to your network. The table shows the assigned IP address, MAC address and expiration time for each DHCP leased client.
Diagnostics The Diagnostics page allows you to test the current configuration. Click „Start‟ to let the modem router perform several tasks to verify if the connection is operational.
Configuration Wizard Click Wizard to configure the modem. The Setup wizard will now be displayed; check that the adsl line is connected and click “Start Scan” to do an automatic detection of the ADSL settings. If you want to configure the modem manually you can click “Skip Scan”. Select your country from the Country list. Select your internet provider. Click Next.
Depending on the chosen provider, you may need to enter your user name and password or hostname in the following window. After you have entered the correct information, click Next. Click Finish to complete the configuration.
Basic Settings LAN Settings This page is used to configure the LAN interface of your ADSL Router. You can set IP address, subnet mask, and IGMP Snooping or modify the IPv6 address range .
You can configure your network and the router to use the Dynamic Host Configuration Protocol (DHCP). This page allows you to select the DHCP mode that this router will support. There are two different DHCP Modes: DHCP Server and DHCP Relay. When the router is acting as DHCP server, please configure the router in the “DHCP Server” page; while acting as DHCP Relay, you can setup the relay in the “DHCP Relay” page.
WAN Settings This page allows you to manually configure the ADSL/WAN settings. The settings on this page require some knowledge concerning the WAN configuration. We advise lessexperienced users to configure the WAN settings using the Wizard. VPI (Virtual Path Identifier) and VCI (Virtual Channel Identifier) define a virtual circuit. VPI: The valid range for the VPI is 0 to 255. Enter the VPI assigned to you. This field may already be configured. VCI: The valid range for the VCI is 32 to 65535.
may already be configured. ATM QoS: Select CBR to specify fixed (always-on) bandwidth for voice or data traffic. Select UBR for applications that are non-time sensitive, such as e-mail. Select VBR for burst traffic and bandwidth sharing with other applications. PCR: Divide the DSL line rate (bps) by 424 (the size of an ATM cell) to find the Peak Cell Rate (PCR). This is the maximum rate at which the sender can send cells.
2.4GHz/5GHz WiFi This section provides the wireless network settings for your router. You can enable and configure the wireless AP function here. SSID: The SSID (up to 32 printable ASCII characters) is the unique name identified in a WLAN. The ID prevents the unintentional merging of two co-located WLANs. Channel Width: Set channel width of wireless radio. Do not modify default value if you don‟t know what it is, default setting is „Auto 20/40 MHz‟.
Security Settings This router provides complete wireless LAN security functions, include WEP, IEEE 802.1x, IEEE 802.1x with WEP, WPA with pre-shared key and WPA with RADIUS. With these security functions, you can prevent your wireless LAN from illegal access. Please make sure your wireless stations use the same security function. Encryption: You can choose “None” to disable the encryption or select “WEP”, “WPA(TKIP)”, “WPA2(AES)” or “WPA2 Mixed” mode for security.
WPA Authentication Mode: There are two types of authentication mode for WPA. Enterprise (RADIUS): It uses an external RADIUS server to perform user authentication. To use RADIUS, enter the IP address of the RADIUS server, the RADIUS port (default is 1812) and the shared secret from the RADIUS server. Please refer to “Authentication RADIUS Server” setting below for RADIUS setting. Personal (Pre-Shared Key): Pre-Shared Key authentication is based on a shared secret that is known only by the parties involved.
Allow: Only allow the wireless clients with the MAC Address you have specified can access to the router. Deny: The wireless clients with the MAC Address you have specified will be denied accessing to the router. MAC Address: Enter the MAC Address of the wireless clients for the filtering control. When you finish, click „Submit‟ to save the settings made and restart the router so the settings will take effect after it reboots.
When you finish, click „Save‟ to save the settings made and restart the router so the settings will take effect after it reboots. Wireless WPS Wi-Fi Protected Setup (WPS) is the simplest way to establish a connection between the wireless clients and the wireless router. You don‟t have to select the encryption mode and fill in a long encryption passphrase every time when you try to setup a wireless connection.
Advanced Settings QoS QoS allows you to classify Internet application traffic by source/destination IP address and port number. You can assign priority for each type of application and reserve bandwidth for it. The packets of applications with higher priority will always go first. Lower priority applications will get bandwidth after higher priority applications get enough bandwidth. This can let you have a better experience in using critical real time services like Internet phone, video conference …etc.
UPnP When the UPnP function is enabled, the router can be detected by UPnP compliant system such as Windows 7. The router will be displayed in the Neighborhood of Windows 7, so you can directly double click the router or right click the router and select “Invoke” to configure the router through web browser. UPnP: Enable or disable UPnP feature. When you finish, click „Save‟ to save the settings made and restart the router so the settings will take effect after it reboots.
You may need to define routes if your home setup includes two or more networks or subnets, if you connect to two or more ISP services, or if you connect to a remote corporate LAN. Click „Add route‟ to add a self-defined route. Destination IP: The destination can be specified as the IP address of a subnet or a specific host in the subnet.
DDNS Dynamic DNS (DDNS) allows you to map the static domain name to a dynamic IP address. You must get an account, password and your static domain name from the DDNS service providers. DDNS Provider: Select your DDNS service provider here. Host Name: Enter the domain name you‟ve obtained from DDNS service provider. Username: Enter the username assigned by the DDNS service provider. Password: Enter the password assigned by the DDNS service provider.
TR-69 As a bidirectional SOAP/HTTP-based protocol, it provides the communication between customer-premises equipment (CPE) and Auto Configuration Servers (ACS). It includes both a safe auto configuration and the control of other CPE management functions within an integrated framework. In the course of the boom of the broadband market, the number of different Internet access possibilities grew as well (e.g. modems, routers, gateways, set-top box, VoIP-phones).
Firewall The Broadband router provides extensive firewall protection by restricting connection parameters, thus limiting the risk of hacker attacks, and defending against a wide array of common Internet attacks. However, for applications that require unrestricted access to the Internet, you can configure a specific client/server as a Demilitarized Zone (DMZ). ACL This page is used to IP addresses for Access Control. If ACL is enabled only the IP Addresses that are in the ACL Table can access the CPE.
IP Filter Click “Add a rule” to add a filtering rule. Enable: Select to enable IP filter rule. Source IP: The source IP address or range of packets to be monitored. Subnet Mask: It is the destination IP addresses based on above destination subnet IP Source Port: This Port or Port Ranges defines the port allowed to be used by the Remote/WAN to connect to the application. Default is set from range 0 ~ 65535. It is recommended that this option be configured by an advanced user.
When you finish, click „Submit‟ to save the settings made. IP Filter Listing #: Item number. Enable: Whether the connection is currently active. Src IP Mask: The source IP address or range of packets to be monitored. Dest IP Mask: This is the destination subnet IP address. Protocol: It is the packet protocol type used by the application, select either TCP or UDP or ICMP Src port: This Port or Port Ranges defines the port allowed to be used by the Remote/WAN to connect to the application.
URL Filter Here it‟s possible to block certain websites. Enter the website you wish to block and make sure the rule is active. Click „Save‟ to apply the new rule. DMZ The DMZ Host is a local computer exposed to the Internet. When setting a particular internal IP Address as the DMZ Host, all incoming packets will be checked by the firewall and NAT algorithms then passed to the DMZ Host. Enable DMZ and enter the IP address for which you want unrestricted access to the internet in the DMZ Host IP address.
Virtual Server Use the Virtual Server function when you want different servers/clients in your LAN to handle different service/Internet application type (e.g. Email, FTP, Web server etc.) from the Internet. Computers use numbers called port numbers to recognize a particular service/Internet application type. The Virtual Server allows you to re-direct a particular service port number (from the Internet/WAN Port) to a particular LAN private IP address and its service port number.
Note : The ports from the start port till the End port will be opened Click „Apply‟ for the changes to take effect. TOOLBOX Sitecom Cloud Security Antivirus software alone is not safe enough. You can now benefit from additional built-in security in your modem or router. Protect all devices in your home network against cybercrime while browsing. Activate in just one click, your network and devices are better secured than ever before.
With the protection of unsafe websites activated the Sitecom Cloud Security will always check if a website is safe. If it is not safe it will inform you that is not safe to enter. If you still wish to visit this webpage click on „proceed anyway‟. Alternatively click „Back to Safety‟ so that your security will not be breached. Configuring Sitecom Cloud Security If you wish to change your security options or to extend your subscription at any time, open http://www.sitecomcloudsecurity.
Or click „License‟ to renew your subscription. Disabling Sitecom Cloud Security If you wish to disable to Sitecom cloud security at any time, open the webpage of your Sitecom product and log in with the supplied credentials (these can be found on the back label on the bottom of your Sitecom device).
Go to Toolbox and select “Sitecom Cloud Security”. Click the “Disable” radio button and click „Apply’ for the settings to take effect. Password You can change the password required to log into the router's system web-based management. Passwords can contain 0 to 12 alphanumeric characters, and are case sensitive. Old Password: Fill in the current password to allow changing to a new password. New Password: Enter your new password. Confirmed Password: Enter your new password again for verification purposes.
Current Time: The current time of the specified time zone. You can set the current time by yourself or configure by NTP server. NTP server: The IP address or the host name of the NTP server. You can select from the list or set it manually. Time Zone Select: Select the time zone of the country you are currently in. The router will set its time based on your selection. When you finish, click „Save‟.so the settings will take effect after it reboots.
Enable Automatic firmware update: When enabled the router will check for updates on the firmware if an updated firmware has been released the router will inform you that a newer firmware is available and offers to download and install the firmware. This page also allows you to manually upgrade the firmware for the router. Click the “Browse” button to select the firmware file and click the “Upgrade Firmware” button to start upgrading.
Addendum A: USB Port Control Center The netUSB functionality of your router requires additional software to work with your computer. The following section will describe how the software can be installed and used. Windows Insert the CD-ROM that was included with your router and select install utility from the cd-menu. The software will inform you about what will be installed. Click Next to continue the installation.
Enter your username and organization if applicable and click Next to continue. Choose a folder where the software should be installed or keep it to default and click Next to continue.
The software is now ready to be installed, Click Install to continue. Once the installation is finished the software will inform you. If “Launch Sitecom USB Device Server” checked the software will automatically be launched after you clicked Finish.
MacOS Insert the CD-ROM that was included with your router and select “Install” from the cdmenu. Click Install to continue installation. Enter your Mac username and password and click OK to continue. Once the installation is finished the software will inform you and requires to restart the system.
Connect & Disconnect “NetUSB” allows you to use USB printers when they‟re actually connected to the Sitecom USB server. The “connect” operation is a software operation that simulates an actual USB device plug-in. Therefore, when you do a “connect” operation in the Control Center, the PC can detect a USB device‟s plug-in, although actually you do not plug in any USB device to your PC. Similarly, the “disconnect” operation is a software operation that simulates the disconnection of the USB device.
NetUSB installation The steps to do installation for USB devices, like MFPs: Make sure the router is turned on. Connect the USB device to the USB port of the router. Run the Control Center. In the “USB MFP Server List” window, you can see the host names and IP addresses all of the Sitecom servers (in blue) on the network, as shown below. Click the server. Then all USB devices attached to the server will be shown. Please follow the user manual of the USB device to install its driver.
PC will automatically detect that the USB device is plugged-in. On the right side of the Windows Task Bar, you can see the information of the new device. Continue to follow the user manual of the USB device to do the rest jobs of installation, until the driver installation has finished. After the installation, you can see the newly created devices on the PC. If the USB device is a MFP, you can see a new printer and a new scanner from the “Control Panel”.
NetUSB Printing using Auto-Connect Printer After the driver is installed, you can see a newly created printer in the Control Panel. Follow the steps below to perform NetUSB printing. In the Control Center, click the MFP server that has the desired printer (or MFP) attached. Click the desired printer (or MFP). Click the “Auto Connect Printer” button and choose “Set Auto-Connect Printer”. The following figure will appear. Choose the desired printer.
When you do a print job again. The control center will automatically do a connecting operation on printing again. This is so-called “Auto Connect / Disconnect” operation. Note: Under the “Auto-Connected Printer” setting, it is not necessary to manually press the “Connect” button when printing. If you press the “Connect” button for printing, please make sure to click “Disconnect” button after you finish the printing. Otherwise, other users cannot print properly.
NetUSB Scanning using Network Scanning In the Control Center, click the MFP server that has the desired MFP attached. Click the desired MFP. Click the “Network Scanner” button. Then you can see that the Control Center will automatically do a “connect” operation. The following window will appear. Choose one of TWAIN or WIA item. Click “OK”. The following window will appear.
Follow the usual steps to do scanning.
Addendum B: GNU/GPL Leaflet Licensing Information Parts of the firmware of the WLM-6600 WiFi Router X6 N900 are subject to the GNU general public license. This product includes third-party software licensed under the terms of the GNU General Public License.. You can modify or redistribute this free software under the terms of the GNU General Public License. Please see Appendix B for the exact terms and conditions of this license.
The free software included in this product is distributed in the hope that it will be useful, but WITHOUT ANY LIABILITY OF OR ANY WARRANTY FROM THE LICENSOR.
Addendum C: GNU/GPL Version 3, 29 June 2007 Copyright © 2007 Free Software Foundation, Inc. http://fsf.org/ Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The GNU General Public License is a free, copyleft license for software and other kinds of works. The licenses for most software and other practical works are designed to take away your freedom to share and change the works.
TERMS AND CONDITIONS 0. Definitions. “This License” refers to version 3 of the GNU General Public License. “Copyright” also means copyright-like laws that apply to other kinds of works, such as semiconductor masks. “The Program” refers to any copyrightable work licensed under this License. Each licensee is addressed as “you”. “Licensees” and “recipients” may be individuals or organizations.
2. Basic Permissions. All rights granted under this License are granted for the term of copyright on the Program, and are irrevocable provided the stated conditions are met. This License explicitly affirms your unlimited permission to run the unmodified Program. The output from running a covered work is covered by this License only if the output, given its content, constitutes a covered work. This License acknowledges your rights of fair use or other equivalent, as provided by copyright law.
works permit. Inclusion of a covered work in an aggregate does not cause this License to apply to the other parts of the aggregate. 6. Conveying Non-Source Forms.
User Product in which it has been modified or installed. Access to a network may be denied when the modification itself materially and adversely affects the operation of the network or violates the rules and protocols for communication across the network.
and (b) permanently, if the copyright holder fails to notify you of the violation by some reasonable means prior to 60 days after the cessation. Moreover, your license from a particular copyright holder is reinstated permanently if the copyright holder notifies you of the violation by some reasonable means, this is the first time you have received notice of violation of this License (for any work) from that copyright holder, and you cure the violation prior to 30 days after your receipt of the notice.
patent license to downstream recipients. “Knowingly relying” means you have actual knowledge that, but for the patent license, your conveying the covered work in a country, or your recipient's use of the covered work in a country, would infringe one or more identifiable patents in that country that you have reason to believe are valid.
15. Disclaimer of Warranty. THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU.
Addendum D: Declaration of Conformity
