Operation Manual

! grinding/cutting discs become very hot during
use; do not touch them until they have cooled
down
! always mount backing pad when using sanding
accessories
! never use a grinding/cutting disc without the label
(“blotter”) which is glued onto it
● Mounting of auxiliary handle E 6
● Removing/mounting/adjusting of safety guard F 7
! ensure that the closed side of the protective guard
always points to the operator
● Before using the tool
- ensure that accessory is correctly mounted and firmly
tightened
- check if accessory runs freely by turning it by hand
- test-run tool for at least 30 seconds at highest no-load
speed in a safe position
- stop immediately in case of considerable vibration or
other defects and check tool to determine the cause
● On/off locking switch H 8
- switch on tool 8a
! be aware of the sudden impact when the tool is
switched on
! before the accessory reaches the workpiece, the
tool should run at full speed
- lock switch 8b
- unlock switch/switch off tool 8c
! before switching off the tool, you should lift it
from the workpiece
! the accessory continues to rotate for a short time
after the tool has been switched off
● Grip ring J 9
For a better grip when working
! always use grip ring J when holding the tool so
that ventilation slots L will not be covered by your
hands
● Speed selection wheel K 2 (9470)
- for determining the right speed table 0 can be used
as reference
! always test out first on a piece of scrap material
● Electronic soft-start (9460/9470)
Ensures reaching the maximum speed smoothly without
a sudden impact when tool is switched on
● Electronic constant speed (9460/9470)
Keeps the speed at a constant level as the load
increases
● Electronic overload protection (9460/9470)
Reduces the speed of the disc automatically in case the
tool is overloaded for a longer period of time
For returning to normal working speed:
- switch off tool
- let tool cool down for 30 seconds
- switch on tool
● Replacing carbon brushes !
This tool is equipped with carbon brushes which pop up
automatically when worn, thus preventing the motor from
being damaged; when the tool stops unexpectedly,
replace the brushes as follows:
! ensure that switch H is in the "O" position
! disconnect the plug
- open the tool with a Torx-15 key (not supplied with the
tool)
- disconnect and remove the worn carbon brushes as
illustrated
- insert and connect the new carbon brushes (supplied
with the tool)
! prevent the spring from popping back by holding
it up with one hand while replacing the carbon
brush with the other hand
- ensure that the wiring is put back as illustrated
! always replace both carbon brushes at the same
time
● Grinding @
- move the tool back and forth with moderate pressure
! never use a cutting disc for side grinding
● Cutting #
- do not tilt the tool while cutting
- always move the tool in same direction as arrow on
tool head, in order to prevent the tool from being
pushed out of the cut in an uncontrolled manner
- do not apply pressure on the tool; let the speed of the
cutting disc do the work
- the working speed of the cutting disc depends on the
material to be cut
- do not brake cutting discs with side pressure
● Holding and guiding the tool
- always hold the tool firmly with both hands, so you will
have full control of the tool at all times
- provide for a secure stance
- pay attention to the direction of rotation; always hold
the tool so, that sparks and grinding/cutting dust fly
away from the body
- keep ventilation slots L 2 uncovered
APPLICATION ADVICE
● Instead of flange B 2 the ”CLIC” quick-clamping flange
(SKIL accessory 2610388766) can be used;
grinding/cutting discs can then be mounted without the
use of accessory keys
GUARANTEE / ENVIRONMENT
● Always keep tool and cord clean (especially the
ventilation slots)
! do not attempt to clean ventilation slots by
inserting pointed objects through openings
! disconnect the plug before cleaning
● This SKIL product is guaranteed in accordance with
statutory/country-specific regulations; damage due to
normal wear and tear, overload or improper handling will
be excluded from the guarantee
● In case of a complaint, send the tool undismantled
together with proof of purchase to your dealer or the
nearest SKIL service station (addresses as well as the
service diagram of the tool are listed on
www.skileurope.com)
9