SIMPLY CLEVER OWNER'S MANUAL Amundsen and Bolero infotainment systems
3V0012720ED
Preface This Owner's Manual is intended for the Amundsen and Bolero infotainment systems. 3V0012720ED Please read these Owner's Manual carefully, because the operation in accordance with these instructions is a prerequisite for proper use of the unit.
Telephone Table of Contents Introductory information 31 Important information about this Owner's Manual 3 Pair and connect 32 Explanations and further information 4 Telephone functions 34 Text messages (SMS) 37 Abbreviations Hotspot (WLAN) and data connection Introductory information Important notes Device overview 6 Hotspot (WLAN) 39 7 Data connection 40 11 Introductory information SmartLink Device operation and settings Device operation Voice control Device settings 13 Android
Important information about this Owner's Manual This Owner's Manual is valid for all types of Amundsen and Bolero infotainment systems (hereafter only devices). The device may differ depending on the vehicle model, in which it is installed in both its appearance and in the arrangement of the controls.
Explanations and further information Structure of these Owner's Manual The Owner's Manual are hierarchically divided into the following areas. ■ Main chapters (e.g. Introductory information) - the title of the main chapter is always shown on the lower right side of the page ■ Chapter (e.g. Equipment overview) ■ Module (for example, Switching the unit on/off) Information search When searching for information in the Owner's Manual, we recommend using the Index at the end of the manual.
Abbreviations Abbreviation Definition Abbreviation TP UPnP 2D planar map display 3D spatial map display VIN a Bluetooth® profile for the one-sided audio data transmission wav A2DP ACC Adaptive cruise control AF Alternative frequencies for the current radio station AM Identification of the radio-frequency range TCS Traction Control of the drive wheels AVRCP Digital radio reception DRM a system for monitoring or restricting the use of digital media content ESC Electronic Stability Contr
Introductory information External devices and applications Important notes Fig. 1 Compatibility of the phones on the ŠKODA websites Introduction to the subject WARNING Concentrate fully at all times on your driving! As the driver you are fully responsible for the operation of your vehicle. ■ Only use the device in such a way that you have control of the vehicle in every traffic situation (e.g.
ŠKODA AUTO does not accept any liability for any damage to the device or vehicle due to the use of incorrect or illegal applications or the improper or unauthorized use of mobile phones. Applications Applications can be installed in external devices (e.g. Mobile, tablet) making it possible to display additional information in the device screen or to operate the device.
Device Description - Amundsen (applies to Yeti) Device Description - Bolero (not applicable to Yeti) The device may differ depending on the vehicle model, in which it is installed in both its appearance and in the arrangement of the controls. Fig.
Device Description - Bolero (applies to Yeti) External module (not applicable to Fabia) Fig. 6 External infotainment module: Bolero / Amundsen Fig.
The brightness level of the screen can be set in the menu Brightness level: . → → screen → CAUTION It is not possible to operate the screen with your fingernails or while wearing gloves. ■ To protect the screen, you can use a suitable screen protector for touchpads that does not affect its functionality. ■ Dirt can be removed from the screen by using a soft cloth and, if necessary, methylated spirits. ■ Software update Fig.
Menu Telephone » page 31 Target-oriented traffic information (TMC) (applies to Amundsen) » page 58 Media Command menu » page 29 Menu SmartLink » page 41 When connecting a supported external device instead of the symbol the actual connection is shown instead of a symbol ▶ -Android Auto » page 42 ▶ - Apple CarPlay » page 43 ▶ - MirrorLink® » page 43 Device operation and settings Device operation Operating principles Adjusting the volume Every change in volume is displayed on the screen.
Scroll symbol - positioning and moving in the menu is possible by moving fingers on the scroll symbol up or down G Menu item with “Checkbox” ▶ - Function is switched on ▶ - Function is switched off H Open a sub menu of the menu item with the “pop-up window” F Operating the menus » Fig.
Search While entering characters, a search is made for corresponding entries. The entry such as a telephone contact to be searched for must be entered along with the special characters (diacritics). By tapping on the function surface a list of matching entries opens. If less than 5 entries were found, a list of the found entries opens automatically. Operating using an application in the external device Applies to Amundsen (not applicable to Yeti).
Operation principle Fig. 14 Screen areas and screen display not recognizing a voice command If a voice command is not detected three times in succession from the device, then the voice control is stopped. Note The display of the Voice mode symbols are dependent of the equipment fitted also on the display of the instrument cluster. Function requirements › The voice command must only be issued when the symbol is displayed and the input tone has completely faded. The input tone can be switched on / off.
voice commands Requirements for optimum voice command recognition of voice without intonation and excessive pauses. ▶ Speak with a normal tone ▶ Avoid bad pronunciation. ▶ Close the doors, windows and sliding roof, in order to avoid disturbing environmental influences on the function of the voice commands. ▶ You are recommended to speak louder at higher speeds, so that the sound of your voice is not drowned out by the increased ambient noise.
Sound settings The scope of the following menu is dependent on the vehicle equipment with the sound system. › Press the button, then tap on the function surface surface. Volume - Volume settings ■ Announcements - Adjustment of traffic announcements volume (TP) ■ Navigation announcements - sets the volume for the navigation announcements ■ Voice control - volume setting for voice output ■ Maximum switch-on volume - Sets the maximum volume after switching on the device ■ Speed-dependent vol.
Note When a language is selected which does not support voice control, the device will indicate with a message on the screen . ■ The messages are generated by the device. The flawless clarity (e.g. road or city name) cannot always be guaranteed. ■ Additional keypad language settings › Press the button, then tap on the function surface Tap on→ Additional keypad languages.
■ ■ Find devices - searches for available devices Bluetooth audio (A2DP/AVRCP) - Turn on/off the ability to connect an audio device (e.g. MP3 player, tablet etc.) Wireless settings Applies to Amundsen (does not apply to Yeti). › Press the button, then tap on the function surface Tap on→ WLAN.
Information symbol in the status line Radio Symbol Operation Introduction to the subject The device allows analogue radio reception of FM and AM frequency ranges as well as DAB digital radio reception. CAUTION For vehicles with window antennas do not stick foil or metal coated stickers to the window - Radio signal reception could be affected. ■ Car parks, tunnels, tall buildings or mountains can interfere with the radio signal even causing it to fail completely. ■ Main menu Fig.
List of available stations Station buttons for your favourite stations Fig. 18 Station buttons Fig. 17 Example, the list of available stations: FM / DAB › To display the list of available stations of the currently selected broadcasting area, rotate the controller in the Radio functional surface surface. › To play, tap on the function surface of the desired station. › To Sort (FM) the stations by name, group or genre, tap on the functional surface A » Fig. 17 » . Information symbols Symbol (e.g.
http://go.skoda.eu/infotainment Note ■ The following image formats are supported: jpg, gif, png, bmp. ■ We recommend a resolution of up to 500 x 500 pixels. TP Traffic programme › To switch on/off the traffic monitoring in the main menu Radio, tap on the function surface → Traffic program (TP). During a traffic announcement, it is possible to cancel the current announcement if necessary by deactivating the traffic monitoring.
If a DAB station is also not available in the FM band due to poor reception, the device will be switched to mute. Media L-band For the DAB radio reception in different countries, different broadcasting ranges are used. In some countries the DAB radio reception is only possible in the so called L-band. Operation Main menu Fig. 19 Media: Main menu If no L-band DAB radio reception is possible in the country then we recommend turning off the L-band. The channel scan is therefore faster.
Select audio source Fig. 20 Display examples of audio source selection › In the Media main menu, tap on the function surface A » Fig. 20 and select the desired audio source. › or: In the folder/track list and in the multimedia database press the functional surface » Fig. 21 on page 23 and select the desired audio source. Function Action Play the next title Tap Finger movement to the left of the screen area A » Fig.
Currently playing title / track playback stopped The title cannot be played (tapping on the function surface shows the cause). Note In the list, the first 1000 entries (titles, directories etc.) are displayed with the oldest creation date. ■ The scanning speed of the folder / track list depends on the connection speed and volume of data.
The SD card slot/s is/are located in an external module in the glove compartment on the passenger side. Insert SD card (Does not apply to Fabia) › “Insert” the SD card in the slot in the direction of arrow (with the cut end facing right), until this locks » Fig. 23-. Insert SD card (Does not apply to Fabia) › Insert The SD card in the direction of the arrow, with the trimmed edge downwards (LHD) or upwards (RHD), into the bay until it “locks” » Fig. 23 - .
Automatic playback stop and disconnection If an Apple device is connected as a Bluetooth® player, and this is connected to the USB input, then the Bluetooth ® connection is not dropped. If playback is cancelled, playback must be started again. Only if USB is selected as the audio source will the Apple device disconnect as a Bluetooth® player. In this regard, an appropriate warning message appears on the device screen.
Supported audio file formats Codec type (File formats) File suffix Max. bit rate Windows Media Audio 9 and 10 wma 384 kbit / s WAV wav Defined by the format (approx. 1.5 Mbit/s) MPEG-1; 2 and 2.5 Layer 3 mp3 MPEG-2 and 4 aac; mp4; m4a FLAC; OGG Vorbis flac; ogg Maximum sampling rate Playlists Image viewer main menu Fig. 24 Images: Main menu 96 kHz m3u pls wpl m3u8 asx 320 kbit / s Defined by the format (approx. 5.
Operation Action Finger motion across the screen to the right (with starting representation) Go to previous image Tap Touch screen using two fingers and pull apart Increase the image size Turning the knob to the right Touch screen using two fingers and close together Reduce the image size Turning the knob to the left Moving the image with an enDrag your finger over the screen in the relarged display quired direction Touch screen using two fingers and move clockwise or counter clockwise (only availaR
Media Command Using the system Introduction to the subject Applies to Amundsen (Does not apply to Yeti). The Media Commandfunction allows playback of audio files or videos in up to two TabletsThat are connected to the device via WLAN, to control the device. The Media Command function enables operation of tablets with the operating system Android or iOS and with the running application ŠKODA Media Command. Main menu » Fig.
WLAN settings Initiation of Tablet-operation Return to main menu Note Some Tablet types allow playback of audio files or videos by an inserted SD card in the tablet. Playback of these tracks may be limited. Supported file formats Select source and control playback Type Video Fig. 27 Select Source / Select Category › To select the playback source tap the functional surface Tap on and select the source-tablet » Fig. 27 - , › to playbackselect the Category » Fig. 27 - and then the title.
If the device to is connected to an external device via Apple CarPlay™, then the use of the Bluetooth®Connection is not possible and the phone menu is not available. Telephone Introductory information Introduction to the subject This chapter covers the operation of a Bluetooth® device connected to the telephone. Depending on the Bluetooth®-profile used it is possible to connect to a telephone or two phones simultaneously to the device.
Enter the telephone number Display the phone contact list, depending on the connection type » page 31, Possible connection types Display a collection of text messages (SMS) (with new messages the number of messages appears next to the functional surface) Display the call list (missed calls, in addition to the function surface, the number of calls when absent is displayed) Menu settings for Telephone Symbols in the status bar Signal strength of the telephone service network Charge status of the
The telephone is compatible with the device. There is no external device connected to the device using Apple CarPlay™. Managing paired external devices The pairing can be initiated from the device or from the telephone. During the pairing and connection process, information messages are displayed in the device screen and the telephone screen. These messages must be observed and if necessary confirmed (e.g. enabling the contact import or connecting the Bluetooth® player etc).
Delete the paired external device ▶ To delete, tap on one of the following function surfaces. Delete all - Delete all external devices - Delete the desired external device ▶ Confirm the deletion by tapping on the function surface Delete. Note To the turn on / off the connectivity of Bluetooth®Player press the button , then the functional surface Tap→ Bluetooth → Bluetooth audio (A2DP / AVRCP).
The main telephone is connected to the device, the telephone contacts from the telephone are used. Management of preferred contacts (favourites) Function interfaces A Contact search B Select a number in the telephone contact list - if a telephone contact contains several telephone numbers, the system displays a menu containing the telephone numbers for this contact after selecting the contact) Display the contact details » Fig.
Call list Fig. 34 Call history / Contact details Telephone call Fig. 35 Incoming call / Current conversation › In the Telephone main menu, tap on the function surface, a call list is displayed » Fig. 34 - . The call list can also be displayed during a telephone call.
Switch on/off hands-free (call to the telephone / switch to device) switch off the hands-free system, in the Telephone main menu, tap on the function surface Tap on hands-freeduring a call. ▶ To switch off the hands-free system, tap on the function surface during a call. ▶ To Note If the incoming call is answered by the auxiliary telephone and the caller has been imported into your contact list from the main telephone, the caller details are displayed.
New text message Viewing the text message After opening the view message function » Fig. 39 - the following functions can be executed. The text can be read out by the device's generated voice The text can be stored as a draft Open a list of templates with the possibility to replace the recorded text by the selected template Open the contact list The message can be edited, as long as the text range is within the entered view. Fig.
› Select a message. The message content and the following menu is displayed.
establish secure connection using WPS ▶ WLAN in device on. ▶ Press the button, then tap on the function Tap on→ WLAN → WLAN → WPS Quick Connect (WPS button). ▶ Turn on the option to connect to the device hotspot using WPS. Connect device to the hotspot (WLAN) of the external device Fig. 41 List of available WLAN networks Connect ▶ WLAN in device on. ▶ Show the list of available hotspots, if necessary, update the list by tapping the functional surfaceSearch.
SmartLink CAUTION Depending on the type of the connected external device and the frequency of use, the charging current may not be sufficient to charge the battery of the connected device. ■ To establish the connection, it is necessary that the date and time in the device are set correctly. If the date and time setting is based on the GPS signal, then problems may arise with establishing a connection with a poor GPS signal reception. ■ Introductory information Introduction to the subject Fig.
Disconnection (appears with active connections) Settings for the menu SmartLink » page 42 Connection set-up ▶ Connect the external device via a connecting cable to the USB input » Owner's Manual. ▶ In the main menu SmartLink Choose the connected external device and the type of communication system if necessary» Fig. 43 - . Return to the main menu of the active connection from another device menu (E.g. From the Radiomenu) ▶ Press the button → active connection ( / / ).
Main menu - functional areas and information in the area A Navigation applications Telephone applications Overview regarding current applications, telephone calls, accepted text messages, tasks in the working directory, weather or similar Music applications List of ŠKODA applications Main menu Fig. 45 Apple CarPlay™: Main menu Start the application ▶ Tap on the functional surface of the desired application to launch the application.
The ignition is switched on. The unit is switched on. The external device to be connected is switched on. Some applications require the data connection in the connected external device to be turned on.
function issues If problems occur with the MirrorLink ®connection, then one of the following messages may occur on the screen. Fault: Transfer- Disconnect the external device and reconnect. MirrorLink® audio is not available. - Disconnect the external device and reconnect MirrorLink® availability on this mobile device is restricted. Using of the connected device is not possible while driving ■ The mobile device is locked.
Navigation Navigation data Introductory information Navigation data source The navigation data is stored on an Original SD Card . Navigation - function sequence In order to ensure the function of the navigation, the Original SD card, with the navigation data, must be inserted in the respective slot » page 24, SD card. Applies to Amundsen. Route guidance is started as follows. › Search for/ enter a new destination or Select one of the stored destinations.
▶ ▶ ▶ ▶ Route details - Displays the route details » page 57 Congestion ahead - Manual adjusts traffic conditions » page 59 Call destination - Search / enter a new destination / stopover » page 47 Stop route guidance - Stops route guidance The following menu is displayed ▶ Store position - Store the current vehicle position as a flagged destination » page 50 ▶ Routes - Display the list of saved routes » page 58 ▶ Destinations - Display the list of stored destinations » page 50 ▶ Last destinations - Displ
Description of the function surfaces A » Fig. 51 A Choice of search - Searching for a destination or POI (point of interest) by name - Search for a point along the route (only works with active route guidance) - Searching for a destination near the entered destination (after selection in destination details » page 54) B Input line C Depending on whether a mark is in the entry line, the following menu is displayed - Map display with selected locations corresponding to the entered characters » Fig.
If several places were found, then the list can be scrolled through by turning the controller or sliding the slider. › Set the desired value and the destination input by pressing the function sur- Note While entering a street name there is an option to enter the centre of a given place as a destination instead of a street name by tapping the function surface Centre. ■ After entering the street name, the house number or intersection can be entered using the name / number of the intersecting road.
Destination memory (manually saved destinations) “Flagged destination” Save (current vehicle position) ▶ In the Navigation main menu, tap on the functional surface → Store position. ▶ By then pressing the functional surface Rename the flagged destination can be renamed and stored as a destination in the destination memory. By storing the next flagged destination, the last flagged destination will be overwritten.
Delete home address › In the Navigation main menu, tap on the functional surface Tap on→ Manage memory → Delete user data → Home address. › Tap the function surfaceDelete and confirm the deletion. Import my destinations Introduction to the subject Fig. 55 MyDestination application on the ŠKODA websites In this chapter, destinations are described which can be imported into the device memory. Custom destinations can be created by means of the ŠKODA application “MyDestination”. Read in the QR code» Fig.
› Tap on the function Surface in the image, a menu opens with the option to start route guidance. Tap map point Fig. 57 Menu after tapping the map point Map Map description Fig. 56 Card description By tapping the map in the Main Menu Navigation the symbol and a menu with the following menu items appear (depending on the context) » Fig. 57. Display the details of the selected item (e.g.
Options for map display Fig. 58 Map options Size of the manually set map scale Size of the automatically set map scale Turn on / off the automatic change of scale Map view in reduced scale Current elevation Manual change of scale Map scale can be change in the following ways. ▶ Turning the control knob . ▶ Touching the screen with two › In the Navigation main menu, tap on the functional surface surface. The following function surfaces are displayed » Fig. 58.
The map is in the 2D display. The map is centred (the functional surface / is hidden). The map scale is max. 10 km away. With a larger map scale than 10 km, the map is automatically oriented towards north. A change of map orientation is only possible in the 2D display when the map is centred on the vehicle position (the function surface or. is hidden). With a larger map scale than 10 km, the map is automatically oriented towards north.
A B C Area with functional surfaces Detailed destination information Destination position in the map A B Display the destination details The destination details can be displayed in one of the following ways.
Graphical driving recommendations The timing of the navigation message is dependent on the road being used and travel speed (e.g. on motorways the first announcement will sound for about 2000 m / 6000 ft before the manoeuvre). The type of navigation announcements can be set: → Nav. announcements. Most common routes The unit automatically stores up to three of the most commonly travelled routes.
▶ Within 15 min. - route guidance is continued taking into account the calculated route. ▶ Between 15 min and 120 min - the screen displays the message Continue route guidance?, after you confirm the message, the route guidance continues using the calculated route. ▶ After 120 min - the route guidance is cancelled. Route Route plan C D The display of the arrival time or the remaining driving time can be adjusted as follows.
Store route the area A , tap the functional surface Save. ▶ Save the edited route as a new route or replace the existing saved route. The device allows you to receive TMC traffic reports (Traffic Message Channel), which contain information regarding traffic obstructions. Stop route guidance ▶ In the area A , tap the functional surface stop . In the list of traffic messages and the map, a max. of 6 messages are displayed, that have a traffic obstruction symbol and a letter A » Fig. 63.
Detail of the traffic report Dynamic route Fig. 64 Detail of the traffic report The device allows an evaluation of the traffic reports received during the route guidance. In fulfilling the following conditions a bypass route is calculated, and the appropriate announcement is issued. The dynamic route function is turned on. The traffic congestion included in the traffic information is on the route. The traffic obstruction will be evaluated by the device as of great importance.
Suggest 3 alternative routes - Switch on/off the menu for alternative routes (economical, fast, short) ■ Route: - Setting the preferred route ■ Most frequent routes - Show/hide the menu of the most frequent routes in the split screen ■ Dynamic route - Switch on/off dynamic route recalculation due to TMC traffic reports ■ Avoid motorway Switch on/off the non-use of motorways in the route calculation ■ Avoid ferries and motorail trains - Switch on/off the non-use of ferries and motorail trains in the rout
Advanced settings › In the Navigation main menu, tap on the functional surface → Advanced settings.
Driving data Vehicle systems CAR - vehicle setting Fig. 66 Driving data Introduction to the subject In the menu CAR travel data and information displayed on the vehicle and some vehicle systems can be set. Description of the individual systems » Owner's Manual . Note Settings relating to the vehicle systems can only be made when the ignition is switched on. Main menu Fig. 65 Function surfaces in the main menu › Press the button The main menu appears with the following functional surfaces » Fig.
■ Vehicle condition Fig. 67 Vehicle condition Winter tyres - Setting an alarm on reaching the speed limit for winter tyres Speed warning - Switching the function Winter tyres on and off Warning at - Setting the speed for the warning ■ ■ Light › Press the button, then tap on the function → Light.
Medium - Medium distance Far - Large distance Very far - Very large distance ■ Front Assist (ambient traffic monitor. sys.
Reset to factory settings › Press the button, then tap on the function surface → Factory settings. In this menu you have the possibility to reset the menu items in the settings of the vehicle systems to factory settings.
Index A A2DP/AVRCP Abort route guidance Adaptive Cruise Control Additional keyboard languages Additional windows Audio Compass Manoeuvre Map Menus Most frequent routes Satellite data Turn on/off Waypoint tour Aim Enter destination using the address entered in map Search Alphanumeric with keyboard Alternative routes Android Auto™ Connection establishment Disconnection Home Page Apple CarPlay™ Connection establishment disconnection Main menu Assistance systems AT THE Audio Media Radio Audio source Automatic d
Device menu CAR Media Command Media (Audio) Navigation Radio Sound Device Menu Pictures SmartLink Telephone Device operation Device screen Device operation using an application in the external device device screen keyboard Device screen Areas Important information Maintenance Operation Disclaimer Diverting calls Door locking Doors - Operation Door unlocking DriveGreen Driver assistance Driving data Display Power on/off Driving lights when raining Dynamic route switch on / off 62 29 22 46 19 16 27 41 31 11
List of paired external devices List of traffic reports Longitude 33 58 46 M main menu Apple CarPlay™ Main menu CAR Images Media Media Command Navigation Radio SmartLink SMS Manage Favourites Manage memory Managing paired devices Manoeuvre Graphical driving recommendations Nav.
Map Map alignment Map scale Most common routes My destinations Navigation announcements Navigation data Nav. announcements Options for map display Preferred type of route Route Route display Route guidance Route information Route memory Route options Route plan Settings Status line Traffic jam ahead Traffic reports (TMC) Trailer towing Voice control Navigation announcements Navigation data Nav.
Route New route Route import Route memory Route calculation Trailer towing Route import Route information Route memory Route options Route plan Route schedule 54 58 58 58 55 55 58 57 58 59 57 57 S Safe removal of the data source Save station Screen See device screen Screen display SD card Search for car park Search for petrol station Search for restaurant Select broadcasting See main menu Select Image Source Images Select source Media Select station See main menu service Images Service Settings Additional
Dialling the telephone number Emergency call Enter telephone number Functions Information service Main menu Operation pair Pairing process Preferred contacts Telephone Telephone book Telephone call Text messages (SMS) Voicemail Telephone book Telephone call Telephone functions Telephone number Text messages new received Time Tiredness detection TMC Detail of the traffic report dynamic route List of traffic reports Requirements TMC (Traffic reports) Tone dialling Touch screen Traffic Detail of the traffic re
Reprinting, duplicating, translating and any other use, either in whole or in part, is not permitted without the written consent of ŠKODA AUTO a.s. ŠKODA AUTO a.s. expressly reserves all rights relating to copyright laws. Subject to change. Issued by: ŠKODA AUTO a.s. © ŠKODA AUTO a.s.
www.skoda-auto.com Amundsen and Bolero: Fabia, Rapid, Rapid Spaceback, Yeti anglicky 11.2016 S00.5614.41.
