SIMPLY CLEVER OWNER´S MANUAL ŠKODA Octavia
Preface You have opted for a ŠKODA – our sincere thanks for your confidence in us. The description of the vehicle operation, important information about safety, vehicle care, maintenance and self-help, as well as technical vehicle data, are included in this Owner's Manual. The operation of some functions and vehicle systems is carried out via Infotainment. Please do not read just this manual, but also the Infotainment Owner's Manual carefully as well.
Service interval display SmartGate Table of Contents On-board literature 4 Notes 5 Structure and more information about the Owner's Manual 6 Abbreviations Safety Passive Safety General information Correct and safe seated position 8 8 8 Seat belts Using seat belts Inertia reel and belt pretensioners 11 11 13 Airbag system Description of the airbag system Airbag overview Deactivating airbags 14 14 15 19 Transporting children safely Child seat Fastening elements 20 20 23 Using the system Cockpit
General Maintenance Technical data Care and maintenance Service work, adjustments and technical alterations Washing vehicle Cleaning vehicle exterior Interior care 178 178 181 182 186 Inspecting and replenishing Fuel Engine compartment Engine oil Coolant Brake fluid Vehicle battery 189 189 194 197 198 200 201 Wheels Tyres and wheel rims Winter operation 205 205 209 Technical data Basic vehicle data Vehicle-specific information depending on engine type 236 236 244 Index Do-it-yourself Emergency eq
On-board literature You will always find this Owner's Manual and the Service plan in the on-board literature for your vehicle. Depending on the equipment, the on-board literature may also include the Infotainment Owner's Manualand in some countries also the brochure On the road. On the move brochure The On-the-road brochure contains the importer's customer service number and the service number in the individual countries, as well as the emergency numbers.
Notes Note Texts with this symbol contain additional information. Terms used The on-board literature contains the following terms relating to the service work for your vehicle. “Specialist” - Workshop - a workshop that carries out specialist service tasks for ŠKODA vehicles. A specialist can be a ŠKODA Partner, a ŠKODA Service Partner, or an independent workshop.
Structure and more information about the Owner's Manual Structure of the manual The Owner's Manual is hierarchically divided into the following areas. ■ Section (e.g. Safety) - the title of the Section is always indicated at the lower left-hand side ■ Main chapter (e.g. Airbag system) - the title of the main chapter is always indicated at the lower right-hand side ■ Chapter (e.g.
Abbreviations Abbreviation rpm Definition Engine revolutions per minute Abbreviation Nm TDI CR Definition Newton meter, measuring unit for the engine torque Diesel engine with turbo charging and common-rail injection system ABS Anti-lock brake system TSA Trailer stabilisation ACC Adaptive cruise control TSI Petrol engine with turbo charging and direct injection AG Automatic gearbox VIN Vehicle identification number AGM Vehicle battery type W TCS Traction control Wi-Fi Wireless data net
▶ Protect children in suitable child seats with correctly fastened seat belts » page 20, Transporting children safely. ▶ Adopt the correct seated position » page 8, Correct and safe seated position. Tell your passengers to assume the correct seated position.
WARNING The front seats and all head restraints must be adjusted to match the body size at all times and the seat belt must always be fastened properly to provide the most effective levels of protection to the passengers. ■ Each occupant must correctly fasten the seat belt belonging to the seat. Children must be fastened » page 20, Transporting children safely with a suitable restraint system. ■ By sitting incorrectly, the occupant is risking life-threatening injuries.
› Swivel the safety lever under the steering wheel in the direction of arrow 1 » Fig. 3. › Adjust the steering wheel to the desired position. The steering wheel can be adjusted in the direction of arrow 2 . › Pull the safety lever in the direction of arrow 3 to the stop.
WARNING (Continued) A seat belt which is hanging too loose can result in injuries as your body is moved forward by the kinetic energy produced in an accident and is then suddenly held firm by the belt. ■ The belt webbing must not run across solid or fragile objects (e.g. spectacles, ball-point pens, keys, etc.). Such objects can cause injury.
WARNING (Continued) Check the condition of all the seat belts on a regular basis. If any damage to the seat belts, seat belt connections, inertia reel or the lock is detected, the relevant seat belt must be replaced by a specialist garage. ■ Damaged seat belts which have been subjected to stress in an accident and were therefore stretched, must be replaced – this is best done by a specialist garage. The anchorage points for the belts should also be checked.
The shoulder part of the seat belt must never run across the neck but must roughly run over the middle of the shoulder and fit snugly against the chest. The lap part of the belt must run across the pelvis, must not be positioned across the stomach and must always fit snugly » Fig. 5 - . Seat belt height adjusters for front seats The seat belt height adjuster makes it possible to adjust the routing of the front seat belts in the area of the shoulder to the body size.
If there is a collision the seat belts are tightened by the belt tensioner so that unwanted body motion is prevented. Airbag system The three-point seat belts are automatically tensioned in the event of a frontal collision of a certain severity. Description of the airbag system The front seat belts are automatically tensioned in the event of a side collision of a certain severity.
The following airbags will be deployed in the event of a severe side collision. System description Read and observe on page 14 first. The inflation of the airbag is carried out in a fraction of a second. When the airbags are deployed they fill with gas and inflate. A grey white or red, non-harmful gas is released when the airbag is inflated. This is perfectly normal and is not an indication of a fire in the vehicle.
WARNING Front airbag and transporting children ■ Never transport children on the front seat of a vehicle without using a proper restraint system. If airbags are deployed in the event of an accident, the child might suffer severe or even fatal injuries! ■ The front passenger airbag must be deactivated if using a rear-facing child seat on the front passenger seat » page 19, Deactivating airbags.
Driver’s knee airbag Fig. 10 Installation of the airbag / Gas-filled Airbag / Safe distance between the legs and the instrument panel Side airbags Fig. 11 Installation locations of airbags: in the front seat/the rear The driver's knee airbag offers adequate protection for the driver's legs. The driver's knee airbag A is located in the lower part of the dash panel below the steering column » Fig. 10.
WARNING Information on correct seated position ■ Your head should never be positioned in the deployment area of the side airbag. You might suffer severe injuries in the event of an accident. This applies in particular to children who are transported without using a suitable child safety seat » page 22, Child safety and side airbag. ■ There must not be any further persons, animals or objects positioned between the occupants and the deployment area of the airbag.
WARNING (Continued) When objects are attached to the sun visor, the visor can not be pivoted to the side windows. This might result in injuries to the occupants if the head airbag is deployed. ■ There must not be any further persons, animals or objects positioned between the occupants and the deployment area of the airbag. In addition, none of the occupants should lean their head out of the window when driving, or extend their arms and hands out of the window.
› Check that the warning light underneath the text » Fig. 14 - lights up after the ignition is switched on. Switching on › Switch off the ignition. › Open the storage box on the front passenger's side. › Fold the key bit out completely for the radio key » . › Carefully insert the key into the key slot in the key switch as far as the stop. › Use the key to turn the slot of the key switch » Fig. 14 carefully into the position . › Pull the key out of the slot in the key switch » .
WARNING (Continued) Children are exposed to an increased risk of injury in the event of an accident if they lean forward or adopt an incorrect seated position when the vehicle is moving. This particularly applies to children who are transported on the front passenger seat as they can suffer severe, or even fatal injuries if the airbag system is deployed! ■ Pay particular attention to the information provided by the manufacturer of the child safety seat regarding the correct routing of the belt.
▶ Set the front passenger seat belt as high up as possible. ▶ When using a child seat where there is a height adjuster in the upper area, the height of the passenger seat belt is to be set so that the belt is not “kinked” in the height adjuster. In the event of an accident, there is the risk of injury to the neck of the child carried due to the seat belt! WARNING Never use a rear-facing child seat on the front passenger seat if the passenger airbag is activated.
Group Front passenger seat Rear seats External Rear seat Centre U U U U U U U U U 0 up to 10 kg 0+ up to 13 kg 1 9-18 kg 2 15-25 kg 3 22-36 kg U is a system for securing child seats quickly and safely. There are two attachment points between the seat backrest and seat cushion of the outer rear seats and front passenger seat for fixing a child seat with the system» Fig. 19. First remove the caps to access the locking eyes. After removing the child seat, replace he caps.
Use of child seats with the system Overview of the usefulness of child seats with the system on each of the seats in accordance with the ECE-R 16 standard. Group Size class of the child seata) Front passenger seatb) Rear seats outside Rear seat middle 0 up to 10 kg E X IL-SU X X IL-SU X X IL-SU IUF X - X IL-SU X - X IL-SU X 0+ up to 13 kg 1 9-18 kg 2 15-25 kg 3 22-36 kg a) b) E D C D C B B1 A The size category is shown on the label attached to the child seat.
Attachment points of the system Fig. 20 Attachment points of the -system is a fastening system, which restricts the movement of the upper part of the child seat. The attachment points for attaching the belt for a child seat with the system are located on the rear side of the outer rear seat backrests » Fig. 20 . Some country-specific models may also feature an attachment point on the back of the middle rear seat backrest » Fig. 20 - .
Fig.
Using the system 22 Cockpit 24 23 Overview 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Electrical power windows Electric exterior mirror adjustment Door opening lever Air outlet vents Parking ticket holder Operating lever (depending on equipment): ▶ Turn signal light, headlight and parking light, headlight flasher ▶ Speed regulating system ▶ Headlight assist Steering wheel: ▶ With horn ▶ With driver’s front airbag ▶ With buttons for operating the information system Instrument cluster Oper
Overview Instruments and warning lights Instrument cluster Introduction This chapter contains information on the following subjects: Overview Revolutions counter Display Coolant temperature gauge Fuel reserve display - Natural gas Fuel reserve display - Petrol / Diesel Counter for distance driven Setting the clock 28 29 29 29 30 30 30 31 The instrument cluster gives the driver basic information such as the current speed, engine speed, the state of some vehicle systems and the like.
Note Depending on vehicle equipment, the MAXI DOT display can be either monochromatic “(black and white)” or colour. Revolutions counter Read and observe on page 28 first. The tachometer 1 » Fig. 22 on page 28 shows the actual engine speed per minute. Coolant temperature gauge The beginning of the red scale range of the tachometer indicates the maximum permitted engine speed of a driven-in and operating warm engine. Fig.
The contents of the fuel tank for petrol / diesel is approximately 50 litres. Fuel reserve display - Natural gas Fig. 25 Gas gauge Read and observe When this fuel level reaches the reserve area A » Fig. 26, the warning light » page 36 illuminates. WARNING For the vehicle systems to function correctly, and thus for safe driving, there must be sufficient fuel in the tank.
Reset counter for distance travelled (trip) › Press button A » Fig. 28 on page 31. Setting the clock Fig. 28 Button in the instrument cluster Read and observe on page 28 first. › Switch on the ignition. › Press and hold the button A » Fig. 28 until the Time is shown in the display. › Release the button A and the system switches to the hour setting function. › Press the button A again and set the hours. › Wait around 4 seconds - the system switches to the minutes setting.
Some warning lights can be accompanied by acoustic signals and messages in the display of the instrument cluster. After switching on the ignition, some warning lights light up briefly as a function test. If the tested systems are OK, the corresponding warning lights go out a few seconds after switching on the ignition or after starting the engine.
Power steering/steering lock (KESSY system) Read and observe on page 32 first. Fault in the power steering illuminates – this indicates a complete failure of the power steering and the steering assist has failed (significantly higher steering forces). illuminates – this indicates a partial failure of the power steering and the steering forces can be greater. Seek help from a specialist garage. Steering lock defect (KESSY system) An audible signal sounds as a warning.
Note On vehicles without the ESC system, the warning light does not illuminate upon deactivation of the TCS system, but a message is only displayed on the display of the instrument cluster. Stability Control (ESC) Read and observe on page 32 first. flashes - the ESC is now being activated. ESC fault Illuminates Error: stabilization control (ESC) ESC ERROR Seek help from a specialist garage.
Engine performance check (petrol engine) Read and observe on page 32 first. illuminates – there is a fault in the engine management system. The system makes possible operation emergency mode - there may be a noticeable reduction in engine performance. The seat belt for the driver and front passenger needs to be replaced. Seek help from a specialist garage. WARNING When a fault in the airbag system occurs, there is a risk of the system not being triggered in the event of an accident.
Other incidents The illumination of the warning light can have the following reasons. ▶ The vehicle is loaded on one side. Distribute loads as evenly as possible. ▶ The wheels of one axle are loaded more heavily (e.g. when towing a trailer or when driving uphill or downhill). ▶ Snow chains are mounted. ▶ A wheel has been changed. CAUTION Under certain circumstances (e.g.
Brake pedal (automatic transmission) Read and observe on page 32 first. illuminates – apply the brake. Natural gas operation Read and observe on page 32 first. illuminates - the vehicle is running on natural gas. Read and observe on page 32 first. illuminates – the main beam or the headlight flasher is switched on. Automatic transmission Read and observe on page 32 first. Gearbox overheated The warning light is only shown in the MAXI DOTdisplay.
If the coolant level is within the specified range and the warning light illuminated again after ignition on, then there may be a malfunction of the cooling fan. ▶ Switch off the ignition. ▶ Check the fuse for the radiator fan, replace if necessary. If the coolant level and the fan fuse are OK and the warning light illuminates again after ignition on do not continue to drive! Seek help from a specialist garage. Coolant temperature too high Illumi- Engine overheat.
To clean the filter, and where traffic conditions permit » , drive as follows for at least 15 minutes or until the indicator light goes out. Gear 4 or gear 5 engaged (automatic gearbox: Position D/S). Vehicle speed at least 70 km/h. Engine speed between 1800-2500 rpm. If the filter is properly cleaned, the warning light extinguishes. If the filter is not properly cleaned, the warning light does not go out and the warning light begins to flash.
Adaptive Cruise Control (ACC) Read and observe on page 32 first. Conditions of the ACC system The warning lights indicate the condition of the ACC system » page 150. Distance warning (Front Assist) Read and observe on page 32 first. illuminates – the safe distance to the vehicle in front is below the minimum. Information on the Front Assist system» page 155. Advance warning/emergency brake (Front Assist) Read and observe on page 32 first.
As long as the faults are not rectified the messages are always shown. After they are displayed for the first time, the warning lights (danger) or (warning) continue to be indicated without information for the driver. Overspeed warning at 120 km/h Read and observe on page 40 first. This function only applies to certain countries. An audible warning signal will sound when the vehicle speed exceeds 120 km/h. The audible warning signal is switched off when the vehicle speed falls below 120 km/h.
If you drive more efficiently this value can increase. Operation With G-TEC vehicles, the following details are displayed. ▶ Total range ▶ Range with ▶ Range with natural gas gasoline Average fuel consumption The indication is calculated continuously since the last deletion of the memory. After erasing the memory, no data will appear for the first 100 m driven. With G-TEC vehicles, the average consumption of fuel currently being used is displayed. Fig.
Current driving speed The display is identical to the display on the speedometer. Average speed The indication is calculated continuously since the last deletion of the memory. Warning when exceeding the set speed Read and observe on page 41 first. After erasing the memory, no data will appear for the first 300 m driven. The system offers the possibility to set a speed limit beyond which an audible alarm will sound and the following warning message appears.
Memory Fig. 31 Memory display: MAXI DOT display ()/segment display () Select memory ▶ Select the driving data information desired. ▶ Confirm details again to select the desired memory. Resetting ▶ Select the driving data information desired. ▶ Select the desired memory. ▶ Reset the selected memory with a long acknowledgement (holding pressed). Note Disconnecting the vehicle battery will delete all memory data. Read and observe on page 41 first. Following driving data is stored in three locations.
Main menu Read and observe Operation using the operating lever on page 44 first. Fig. 32 Buttons: on the operating lever Call up the main menu › Press and hold the button A on the operating lever » Fig. 32 on page 45. or › Press and hold the dial G on the multifunction steering wheel » Fig. 33 on page 46.
Operation using the multifunction steering wheel Button / dial F Action Press briefly Press and hold button Press briefly G Fig. 33 Buttons/dials: on the multifunction steering wheel Read and observe on page 44 first.
Then turn dial G » Fig. 33 on page 46 on the multifunction steering wheel to display the Last destinations menu. The menu shows the Home address menu item and a list of recent destinations. When you select one of the menu items, the destination name and the following items are displayed.
Missed calls (if there are several missed calls, the number of calls is shown next to the symbol) Switch-off microphone Menu itemAssist systems Read and observe on page 44 first. Select menu item Assist systems › Select and confirm Assist systems in the main menu. or › Press the button on the multi-function steering wheel . In the menu item Assist systems, the Front Assist and Lane Departure Warning (Lane Assist) systems can be enabled/disabled.
Compass point display Fig. 34 Compass display Service interval display Introduction This chapter contains information on the following subjects: Displaying the distance and days until the next service interval Service messages Resetting the service interval display 49 50 50 The service interval display shows the time and mileage to the next service event. Read and observe on page 44 first. Applies to vehicles with factory-installed navigation system.
Service messages Messages before reaching the scheduled service date Before the next service date has been reached, after switching on the ignition, the symbol as well as a message about the mileage or days until the next service event appears in the display. SmartGate Introduction Fig.
CAUTION To increase the access security to the transmitted vehicle data, once the ŠKODA application has been started, you are requested to change the password/PIN code if the default password/PIN code has not yet been changed » page 52, Password/PIN code change. It is not possible to start the ŠKODA application without changing it. ■ ŠKODA accepts no responsibility for any problems caused by incompatibility or improper functioning of the communication devices.
Disconnection The connection can be switched off in one of the following ways. › Switch off the ignition for longer than 5 seconds (for vehicles with a starter Changing the password for the Wi-Fi connection › Open the SmartGate web interface. › In the “WPA / WPA2 key:” menu item, enter the new password (8 to 63 alphanumeric characters and special characters, small and capital letters). button, switch off the engine and open the driver's door). › End the connection in the SmartGate application.
▶ The Unlocking and opening ▶ The ▶ The ▶ The ▶ The ▶ The Unlocking and locking Introduction This chapter contains information on the following subjects: Locking/unlocking using the key via the lock cylinder Unlocking/locking with the remote control key Unlocking / locking - KESSY Locking and unlocking the vehicle with the central locking button Safe securing system Individual settings Opening/closing a door Child safety lock Malfunctions 54 54 55 55 56 56 57 57 57 If the doors or the luggage comp
Locking/unlocking using the key via the lock cylinder Fig.
Unlocking / locking - KESSY If the boot lid is closed after locking the vehicle and the key with which the vehicle was locked remains in the luggage compartment, the lid is unlocked (partially opened). The turn-signal lights flash four times as an indication that the boot lid has been unlocked again. The boot lid remains released(partially opened). The following message is shown in the information cluster display. Key in vehicle.
WARNING Doors locked from the inside make it difficult for rescuers to get into the vehicle in an emergency – danger to life! Read and observe and on page 53 first. As soon as the vehicle is locked from the outside, the safe lock prevents opening the doors from the inside. This function is pointed out by the following message on the display of the instrument cluster after switching out the ignition.
Opening/closing a door Child safety lock Fig. 41 Door handle/door opening lever Read and observe and on page 53 first. Opening from the outside › Unlock the vehicle. › Pull on the door handle A in the direction of the arrow » Fig. 41. Opening from the inside › Pull on door opening lever B of the door and push the door away from you. Closing from the inside › Grasp pull handle C and close the door.
Failure of the system KESSY If the following message is displayed in the display of the instrument cluster, then help is required from a specialist company. Keyless access system faulty. KEYLESS ACCESS SYSTEM FAULTY Key battery discharged If the voltage of the key battery is too low, the following message appears in the display of the instrument cluster. Change the key battery! KEY BATTERY PLEASE CHANGE Replace the battery » page 223.
By disabling the interior monitoring and the anti-towing the safe lock is switched off. Boot lid opening/closing CAUTION The opened glasses storage compartment reduces the effectiveness of the interior monitor. To ensure the full functionality of the interior monitor, the glasses storage compartment must always be closed before locking the vehicle. Luggage compartment lid Introduction Fig.
Electric boot lid Operating description Introduction This chapter contains information on the following subjects: Operating description Set the top position of the lid Malfunctions 60 61 61 The boot lid (hereinafter referred to as lid) can be operated electrically and manually in the event of an emergency » page 61. If the lid hits an obstacle when opening or closing, it stops and an audible signal sounds. When closing the flap is lifted additionally. Fig.
Stop lid movement The lid movement can be stopped by pressing one of the following operating elements. ▶ Button B » Fig. 45. ▶ Button C » Fig. 46. ▶ Symbol button on the remote control key (for about 1 s). ▶ Handle A » Fig. 45. Malfunctions Read and observe and Examples of operational malfunctions Description of the malfuncPossible solutions tion When opening the lid using the symbol key on the key or the button C » Fig. 46 an acoustic signal sounds.
The windows can be operated electrically from the following locations; all windows from the driver's seat and also via the buttons for the windows in the passenger door or the rear doors. WARNING The windows should be closed carefully – risk of injury! CAUTION In the event that the windows are frozen, first of all remove the ice » page 184, Windows and external mirrors and only then operate the window lift. Otherwise, the window sealing and the window lift mechanism could be damaged.
Closing › Pull gently on the top edge of the corresponding button and hold until the window has moved into the desired position. Opening/closing the windows in the front passenger door and in the rear doors Releasing the button causes the window to halt immediately. Fig. 49 Power window button The window can also be fully closed automatically by pulling the button up to the stop. Renewed pulling of the button causes the window to stop immediately.
If the obstacle prevents the window from being closed during the next 10 seconds, the closing process is interrupted once again and the window goes down by several centimetres. Convenience opening or closing the window using the key in the driver's door locking cylinder is only possible within 45 seconds of locking the vehicle. The movement of the window is stopped immediately when the respective button is released.
CAUTION During the winter it may be necessary to remove any ice and snow in the vicinity of the sliding/tilting roof before opening it to prevent any damage to the opening mechanism. Operation Power limit Read and observe on page 64 first. The sliding/tilting roof is fitted with a force limiter. If there is an obstacle, the closing process is stopped and the window goes down by several centimetres. Fig.
Sliding / tilting roof malfunction Read and observe Electrical operation of the sunblind on page 64 first. Fig. 53 Operation of the sun blind If the battery has been disconnected and reconnected, it is possible that the sliding/tilting roof will not operate. The sun roof must be activated. Activation sequence › Switch on the ignition. › Set the switch to the position » Fig. 50 on page 65 or » Fig. 51 on page 65. › Press the switch on the recess E down and pull forwards.
› Release the button.
Note The headlights may mist up temporarily. When the driving lights are switched on, the light outlet surfaces are free from mist after a short period, although the headlight lenses may still be misted up in the peripheral areas. This mist has no influence on the life of the lighting system. ■ If the visibility is poor and the lights are not on (except daytime running light) the brightness of the instrument lighting reduces to alert the driver to switch on the lights in due time.
Activating/deactivating function on vehicles with Infotainment The function can be disabled/enabled in the Infotainment » Owner´s Manual Infotainment, chapter CAR - vehicle settings. Deactivating on vehicles without Infotainment › Switch off the ignition. › Pull the indicator / main beam lever towards the steering wheel, push down and hold in this position. › Switch on the ignition. › Hold the lever in this position for min. 3 seconds after switching on the ignition.
Automatic driving lamp control Xenon headlight Fig. 56 Light switch: AUTO position Read and observe on page 67 first. The Xenon headlight (hereinafter referred to as system) ensures that the roads are illuminated independent of the traffic and weather conditions.
Dynamic cornering lights The cone of light in front of the vehicle is adjusted to the steering angle so that the road in the curve is illuminated. This function is active at speeds greater than 10 km/h and in all system modes. Fig. 58 Operating lever: High beam assistant activation/deactivation travel mode If the travel mode is activated, there is no automatic cone of light adaptation in front of the vehicle.
The warning light goes out. The high beam turns off. › If the headlight is not currently switched on automatically, move the lever in- Front and rear fog light to position A (spring-tensioned position) . Fig. 59 Light switch – switch on front and rear fog light The warning light goes out. The high beam turns on. Information message The messages and information are indicated in the instrument cluster display. Fault: Light Assist LIGHT ASSIST FAULT Seek help from a specialist garage.
Fog lights with the CORNER function Read and observe on page 67 first. The function CORNER provides better illumination of the nearby environment when turning, manoeuvring or anything similar. The function automatically switches on the fog lights on each side of the vehicle, if the following conditions are met. The turn signal is switched on or the front wheels are turned sharply 1). The vehicle speed is below 40 km/h. The low beam is switched on. The fog lights are not switched on.
When the hazard warning system is on and the indicator light is switched on (e.g. when turning), the hazard warning lights are switched off temporarily and only the turn signal flashes on the relevant side of the vehicle. Read and observe Introduction This chapter contains information on the following subjects: Parking lights Interior lights on page 67 first. The side light is provided for lighting of the parked vehicle. Switching on the side light on one side › Switch off the ignition.
Automatic operation of the lamp – position The system is turned on when any of the following is present. ▶ The vehicle is unlocked. ▶ One of the doors is opened. ▶ The ignition key is removed. The system is turned off when any of the following is present. ▶ The vehicle is locked. ▶ The ignition is switched on. ▶ About 30 seconds after all the doors have been closed. Switch for rear lights (variant 2) » Fig.
The lighting switches off around 30 seconds after the front door is closed or the ignition is switched on. Buttons for the heating in the centre console (depending on vehicle equipment) » Fig. 65 Activate/deactivate the heated rear window Activate/deactivate the windshield heating WARNING If the entry light is on, do not touch its cover – risk of burns! When the heater is activated, a lamp illuminates inside or below the button. The heater automatically switches off after approximately 10 minutes.
A B Make-up mirror with cover (the cover can be pushed in the direction of the arrow) Parking ticket holder WARNING When objects are attached to the sun visor, the visor can not be pivoted to the side windows. This might result in injuries to the occupants if the head airbag is deployed. The windscreen wipers and the wash system only operate if the ignition is switched on and the bonnet and boot are closed.
Note Each time the ignition switches off for the third time, the position of the windscreen wipers changes. This counteracts an early fatigue of the wiper rubbers. ■ The windscreen washer nozzles for the windscreen are heated when the engine is running and the outside temperature is less than approx. +10 °C. ■ Windscreen wipers and washers Spraying and wiping the windscreen After releasing the operating lever, the wipers will make from 2 to 3 wiper strokes.
The headlight washer system works under the following conditions. The ignition is switched on. The low beam is switched on. The outside temperature is about -12° C to +39° C. Interior mirror dimming To ensure the correct functioning of the system, even in winter, this needs to be regularly cleared of snow and ice, e.g. free with a de-icing spray.
Exterior mirrors Fig. 70 Exterior mirror operation Automatically folding in and folding back both exterior mirrors The exterior mirrors are automatically collapsed after locking the vehicle in the park position. The exterior mirrors are folded out automatically after unlocking the vehicle in the driving position. Automatic folding in / out of both mirror housings can be activated or deactivated in the Infotainment » Owner´s Manual Infotainment, chapter CAR - vehicle settings.
CAUTION Never adjust exterior mirrors with the fold-in function by hand - risk of damaging the electric mirror actuator! ■ When the mirror is swung by external influences (due to impact during manoeuvring, for example), then first fold-in the mirror by turning the knob and wait for a loud clapping noise.
Manually adjusting seats Fig. 71 Control elements on the seat Read and observe on page 81 first. The seats can be adjusted by the respective operating element being pulled in the direction of arrows, pressed or rotated. Control elements on the seat » Fig.
Headrests - removing and installing Fig. 74 Rear headrest: moving up/down Read and observe on page 81 first. Adjust front support › Press and hold the safety button A » Fig. 73. › Move the supports into the required position. Adjust rear support › Grasp the restraint and move upwards in the direction of 1 » Fig. 74. › In order to push the supports downward, press the safety button B in the direction of arrow 2 and hold down. › Press in the support in the direction of arrow 3 .
Memory Function of the electrically adjustable seat Retrieving the saved setting Ignition Fig. 76 Memory buttons and SET button Driver's door Press the required memory button B » Fig. 76 Open Closed Open Closed Short Long Long Long Switched off Activated Stopping the ongoing adjustment ▶ Press any button on the driver's seat or the button key. Read and observe on page 81 first. The pre-set buttons on the driver's seat make it possible to save the driver's seat and exterior mirror positions.
When the vehicle is next unlocked using the same key, the driver's seat and the external mirrors assume the positions stored in the memory of this key. Seat heaters Saving front passenger mirror settings for reversing The function of lowering the passenger mirror surface when reversing must be enabled in Infotainment » Infotainment Owner´s Manual , chapter CAR - Vehicle Settings . › Unlock the vehicle with the relevant remote control key. › Switch on the ignition.
WARNING If you have a subdued pain and/or temperature sensitivity, e.g. through medication, paralysis or because of chronic illness (e.g. diabetes), we recommend not to use the seat heating. There may be difficult to heal burns. If the seat heating is used, we recommend to make regular breaks in your journey when driving long distances, so that the body can recuperate from the stress of the journey. Please consult your doctor, who can evaluate your specific condition.
Folding forward › Place the lever in position 1 » Fig. 80. › Fold the backrest in the direction of the arrow 2 . Seat backrests The locking mechanism must audibly snap into place. Folding backwards › Place the lever in position 1 » Fig. 80. › Fold the seat backrest in the opposite direction of the arrow 2. The locking mechanism must audibly snap into place. WARNING The front passenger airbag should be switched off when transporting objects on the seat which was folded forwards » page 19.
› Fold the backrest in the direction of the arrow 2. In the undivided seat back, press the release handles A on both sides of the seat back at the same time. Folding forward from the luggage compartment There is a lever on the left side of the luggage compartment for unlocking the left rear seat backrest. There is a lever on the right side of the luggage compartment for unlocking the right and the middle rear seat backrests.
WARNING The through-loading channel is only intended for transporting skis that are placed in a properly secured, through-loading bag.
WARNING (Continued) No objects should be placed in the storage compartments nor in the drinks holders; the vehicle occupants could be endangered if there is sudden braking or the vehicle collides with something. ■ Ash, cigarettes, cigars and the like. may only be placed in the ashtray! ■ Read and observe on page 89 first. Opening › Raise the handle and open out the compartment in the direction of the arrow » Fig. 85.
Storage compartment in the front centre console Phonebox When the telephone is inserted into the Phonebox, the telephone signal increases in strength by about 20%. This reduces the level of phone battery discharge and the electromagnetic radiation inside the vehicle. › Place the telephone in the storage compartment B with its back on the induction panel » Fig. 88.
Placement of the cup holders » Fig. 89 A In the front centre console B In the rear armrest WARNING The cigarette lighter also works if the ignition is switched off. When leaving the vehicle, never leave persons who are not completely independent, such as children, unattended in the vehicle. These could operate the lighter and get burned, start a fire or damage the interior. ■ Take care when using the cigarette lighter! Improper usage can case burns.
The insertion of the insert and closing of the ashtray is carried out in reverse order. WARNING Instructions for devices connected to the sockets. ■ Safely stow all devices during the journey to prevent them from being thrown around the interior in the event of a sudden braking manoeuvre or an accident – risk of death! ■ The devices may warm up during operation – risk of injury or fire! If the device becomes too hot, switch it off and disconnect it from the power supply immediately.
Note We recommend that you use 20x30 cm bags. Multimedia holder Fig. 95 Multimedia holder Fig. 94 Replacing the bags Read and observe on page 89 first. The waste container can be inserted into the slots in the doors. Insert waste container › Position the waste container at the front edge of the slot. › Push the waste container to the back in the direction of the arrow 1 » Fig. 93. › Move the waste container in the direction of the arrows as required 2 .
Storage compartment under the front arm rest Fig. 96 Opening the storage compartment Closing › Swivel the lid of the glasses storage box against the direction of the arrow » Fig. 97 until it audibly clicks into place. WARNING The compartment must only be opened when removing or inserting glasses, and otherwise must be kept closed – risk of injury. CAUTION Do not put any heat-sensitive objects in the glasses storage box - with high temperatures there is risk of damage.
Air supply operation The air supply can be operated by turning the rotary switch in the direction of arrow A as far as the stop » Fig. 98. Opening Closing Opening the air supply when the air conditioning system is switched on allows cooled air to flow into the storage compartment. Opening the air inlet when the air conditioning system is on causes fresh or interior air to flow into the storage compartment.
Storage compartment in the rear centre console Fig. 101 Opening the storage compartment The socket only works if the ignition is switched on. Use › Open the cover in the direction of the arrow » Fig. 102. › Connect the plug for the electrical appliance to the socket. When plugging in the connector the child safety lock is unlocked and the outlet is activated. Warning light Read and observe Display indicator light Illuminates green Flashes red on page 89 first.
CAUTION The power socket can only be used for connecting approved electrical accessories with a two-pin 230V plug, with a total power uptake of up to 150 watt. ■ Place the connector on the electrical device into the power socket as far as it can go to create a connection between the contacts. ■ If the connector of the electrical device is not inserted fully into the power socket, the child safety lock might release, and the power socket be activated. The electrical device is still not supplied with power.
AUX and USB inputs Install/remove Fig. 104 Installation locations of the AUX and USB inputs Read and observe on page 89 first. Fig. 105 Position adapter/install holder The AUX input is above the storage compartment in the front centre console and is identified with the mark » Fig. 104. The MDI input is above the storage compartment in the front centre console and is identified by the symbol . Additional information» Owner´s Manual Infotainment. Multimedia holder Introduction Fig.
Multifunction pocket Folding double hooks Foldable hook Floor covering Floor covering on both sides Luggage net Luggage compartment cover Roll-up cover Storage compartment with cargo element Storage compartments under the floor covering Multi-function pocket Class N1 vehicles Handle holder Fig. 107 Tilt and rotate holder Read and observe on page 99 first. Tilt and rotate holder The holder may be tilted 30° in the direction of arrow 1 and rotated through 360° in the direction of arrow 2 » Fig. 107.
The warning light turns off when the tailgate is closed. If the boot lid is open and the ignition switched off, the light will extinguish automatically after around 10 minutes. WARNING Never exceed the maximum permissible load of the respective fasteners, nets, hooks etc. as heavy objects are not e sufficiently secured - there is a risk of injury! ■ If the cargo is tied down with unsuitable or damaged lashing straps, injuries can occur in the event of braking manoeuvres or accidents.
CAUTION Do not place any sharp objects in the nets – risk of damaging the net. ■ For vehicles with lashing eyes D » Fig. 109 on page 101, only the following nets can be attached. ■ Horizontal pocket behind the seats. ■ Floor net, which can be attached to the rear fastening elements A » Fig. 109 on page 101 in the rear area. Fixing nets ■ Multifunction pocket Fig. 113 Securing the multifunction pocket Fig. 111 Fastening examples for nets Fig.
Fold down hooks Folding double hooks › Press on the lower portion of the hook Fig. 114 Folding double hooks Read and observe and A and then fold it in direction of the arrow » Fig. 115. Floor covering on page 101 first. The folding double hook » Fig. 114 is used to fasten small items of luggage, e.g. bags. The folding double hook can be located on either of the two sides of the luggage compartment, according to the model.
Note For easier turning of the covering, use the loop attached. Fig. 119 Luggage compartment cover stowed behind the rear seats Luggage net Fig. 117 Luggage net Read and observe and on page 101 first. If the support straps A » Fig. 118 are attached to the boot lid, then opening the lid will raise the boot lid cover (hereafter referred to as cover). Read and observe and on page 101 first. The net at the bottom of the luggage compartment cover » Fig.
CAUTION When closing the boot lid, jamming and damage to the cover or the side trim panel can occur if handled incorrectly. The following guidelines must be observed. ■ The recesses in the cover B » Fig. 118 must lock in the holders in the side trim panel C . ■ The items which are transported must not exceed the height of the cover. ■ The cover must not be jammed in the surrounding seal of the luggage compartment lid when it is in the raised position.
Storage compartment with cargo element Fig. 122 Remove storage compartment Secure load › Remove the cargo element (part of the storage compartment cover) in the direction of the arrow » Fig. 123- . › Attach the Cargo element with Velcro to the rear seats on the floor of the luggage compartment » Fig. 123 - or attach to the fabric side of the double-sided floor covering. CAUTION When using the storage compartment, take care not to damage it or the luggage compartment lining.
CAUTION The following instructions must be observed to avoid damage to the storage compartments. ■ Do not stored any sharp objects in the storage compartments. ■ Do not place any point-pressure in the storage compartment. ■ Carefully place the items in the storage compartments. ■ Multi-function pocket › Place the rear bar onto the two hooks that are folded forward in the direction of the arrow 3 all the way to the stop.
The maximum permissible load of the variable loading floor is 75 kg. For the transport of heavy loads, adjust the variable loading floor in the lower position » Fig. 127 on page 108. Positions of the variable loading floor After an audible click, the variable loading floor can be stowed in the upper position by pushing it forward.
Dividing the luggage compartment Using the net partition Fig. 129 Dividing the boot with variable loading floor The luggage compartment can be divided with the variable loading floor in the lower and upper position. › Raise the rear of the variable loading floor by the handle A » Fig. 129. › Push the rear edge of the variable loading floor into the grooves B in the Fig. 130 Open part of the roll-up luggage compartment cover / release lever direction of the arrow.
If the crossbar is hooked into the receptacle E to the left for example, then press on the crossbar in the direction of the arrow 1 and insert into the receptacle E to the right. › Make sure that the crossbar is firmly seated in the fittings E . › Fold back part of the roll-up luggage compartment cover A in the opposite direction of the arrow » Fig. 130. Using the net partition behind the rear seats › Fold out part of the roll-up luggage compartment cover A in the direction of the arrow » Fig. 130.
The height of the vehicle changes after mounting a roof luggage rack system including the load that is being transported. Compare the vehicle height with available clearances, such as underpasses and garage doors. ■ Ensure the roof aerial is not impaired by the load being transported. ■ Stowing the roof rack Note We recommend that you use a roof rack from ŠKODA Original Accessories. fixing points for base support Fig.
Roof load Read and observe Heating and ventilation and on page 110 first. Do not exceed the permissible roof load of 75 kg, this includes the carrier system. The full permissible roof load cannot be used if a roof rack system with a lower load carrying capacity is used. The maximum capacity of the carrier system should never be exceeded.
WARNING For your own safety and that of other road users, ensure that all the windows are free of ice, snow and misting. The blower should always be on to prevent the windows from misting up. ■ Under certain circumstances, air at a temperature of about 5 °C can flow out of the vents when the cooling system is switched on. ■ CAUTION The air inlet in front of the windscreen must be free of e.g. ice, snow or leaves to ensure that the heating and cooling system operates properly.
Information on the cooling system The cooling system operates only if the following conditions are met » page 112. The warning light below the button » Fig. 136 illuminates after activation, even if not all of the conditions for the function of the cooling system have been met. The lighting up of the indicator light in the button signals the operational readiness of the cooling system. When the air distribution control is turned to position the cooling system is activated.
Setting temperature The temperature can be adjusted on the Climatronic control unit or in the Infotainment » Owner´s Manual Infotainment, chapter Setting the heating and the cooling system. Setting the individual operating modes » Owner´s Manual Infotainment, chapter Setting the heating and the cooling system. After the automatic mode is switched on, Climatronic works in the last selected mode. The temperature can be set between +16 °C and +29.5 °C.
This automatic on/off switching of the recirculated-air mode can be activated or deactivated in the Infotainment » Owner´s Manual Infotainment, chapter Setting the heating and the cooling system. Air outlet vents If the button is pressed when the recirculation modes is switched on, the recirculated-air mode is switched off. Depending on the moisture conditions in the vehicle interior the air recirculation may also shut-down automatically.
Opening › Turn regulator B » Fig. 138 or » Fig. 139upwards. Aux. heating The auxiliary heating can be used when both when stationary, when the engine is switched off, to preheat the vehicle and also while driving (e.g. during the heating phase of the engine). Closing › Turn regulator B » Fig. 138 or » Fig. 139downwards. Depending on the setting of the air distribution on the front panel of the heater, the manual air conditioning or the Climatronic, the following air vents are active.
Note The auxiliary heating only switches the blower on, if it has achieved a coolant temperature of approx. 50 °C. ■ At low outside temperatures, this can result in a formation of water vapour in the area of the engine compartment. This is quite normal and is not an operating problem. ■ So that warm air can flow into the vehicle interior after switching on the aux. heating, you must maintain the comfort temperature normally selected by you, leave the fan switched on and leave the air outlet vents in open.
Display warning light A » Fig. 141 Radio remote control Fig. 141 Radio remote control Quickly flashes green for around 2 seconds. Flashes red for around 2 seconds. Lights up orange for around 2 seconds, then green or red. Read and observe and Lights up orange for around 2 seconds, then flashes green or red. on page 117 first. Using the radio remote control, the aux. heating and ventilation (hereinafter referred to as heater) can be switched on or off.
CAUTION Only start the engine when the engine and the vehicle are stationary - there is a danger of starter and engine damage! ■ Do not push-start the engine – there is a risk of damaging the engine and the catalytic converter. The battery from another vehicle can be used as a jump-start aid » page 219.
› Switch on the ignition » page 121. The steering column lock is unlocked. If the ignition switch can not be turned on, then turn the steering wheel back and forth slightly and thereby unlock the steering lock. Turning ignition on/off and starting the engine Fig. 142 Positions of the vehicle key in the ignition lock If the engine does not start within 10 seconds, turn the key to position 1 . Repeat the start-up process after approx. half a minute.
CAUTION The system can recognize the valid key, even if it has been accidentally left on the vehicle roof - there is danger of loss or damage to the key! ■ Only start the engine when the engine and the vehicle are stationary - there is a danger of starter and engine damage! ■ Do not push-start the engine – there is a risk of damaging the engine and the catalytic converter. The battery from another vehicle can be used as a jump-start aid » page 219.
WARNING Never let the vehicle roll with locked steering lock - there is a risk of accident! Switching ignition on / off Read and observe and on page 122 first. Note The engine running noises may louder at first be louder for a short time after starting the cold engine. This is quite normal and is not an operating problem. ■ You should not switch on any major electrical components during the heating period otherwise the vehicle battery will be drained unnecessarily.
Problems starting the engine Note When attempting to start, the key bit must be pointed towards the button » Fig. 144. ■ If the engine fails to start after pressing the button with the key, seek specialist help. ■ Fig. 144 Starting the engine - press the button with the key START-STOPsystem Introduction This chapter contains information on the following subjects: Read and observe and on page 122 first.
Operation Fig. 145 Display Vehicles with manual transmission The engine is automatically switched off as soon as the vehicle comes to a halt, the shift lever is moved into neutral and the clutch pedal is released. The engine is automatically started as soon as the clutch pedal is depressed. Vehicles with automatic transmission The engine is automatically switched off as soon as the vehicle comes to a halt and the brake pedal is operated.
Manually deactivating/activating the system Fig. 146 Button for the START-STOP system Brakes and parking Introduction This chapter contains information on the following subjects: 126 127 128 Information on braking Handbrake Parking WARNING Greater physical effort for braking is required when the engine is switched off – risk of accident! ■ During the braking procedure on a vehicle with manual transmission, when the vehicle is in gear and at low revs, press the clutch pedal.
Wet roads or road salt The performance of the brakes can be delayed as the brake discs and brake pads may be moist or have a coating of ice or layer of salt on them in winter. The brakes are cleaned and dried by applying the brakes several times » . Corrosion Corrosion on the brake discs and dirt on the bake pads occur if the vehicle has been parked for a long period and if you do not make much use of the braking system. The brakes are cleaned by applying the brakes several times » .
WARNING Please note that the handbrake must be fully released. A handbrake which is only partially released can result in the rear brakes overheating. This can have a negative effect on the operation of the brake system – risk of accident! Manual gear changing Fig. 148 Gearshift pattern of 5-gear or 6gear manual gearbox Parking Read and observe and on page 126 first. When stopping and parking, look for a place with a suitable surface » .
In the driver's footwell, only a footmat, which is attached to the two corresponding attachment points may be used. Only use factory-supplied footmats or footmats from the range of ŠKODAOriginal Accessories, which are fitted to two attachment points. WARNING No objects may be placed in the driver's footwell – risk due to obstruction or limitation of pedal operation. Note After the ignition is switched off, the ignition key can only be withdrawn if the selector lever is in the position P.
D / S - mode for driving forward (Normal program) / mode for driving forward (Sport program) The system switches from one mode to the other by moving the selector lever into the spring-loaded position » Fig. 149. In mode D or S, the forward gears are shifted automatically depending on the engine load, the operation of the accelerator pedal, the vehicle speed, and the selected driving mode . In mode S , the forward gears are shifted automatically up and down at higher engine speeds than in mode D.
The gearshift indicator must be observed when changing gear » page 41. › Move the selector lever into the desired position » page 129 and then release Switching to manual shifting › Push the gear selector from position D/S towards the right, or left in a righthand drive vehicle. › Release the brake pedal and accelerate. When switching to the manual shifting while driving, the current gear is maintained. Shifting up gears › Push the selector lever forwards + » Fig. 151. › Pull the paddle + » Fig.
› START STOP deactivate » page 126, Manually deactivating/activating the New brake pads New brake pads have to first “grind in” because these do not initially have the best possible braking effect. system. › Fully depress and hold the brake pedal with your left foot. › Fully depress the accelerator pedal with your right foot. › Release the brake pedal. Drive especially carefully for the first 200 km or so. The vehicle starts off with maximum acceleration.
In Infotainment, the display is shown of up to three consumers which are currently showing the highest degree of fuel consumption » Owner´s Manual Infotainment, chapter CAR - vehicle settings. Use the cooling system economically The air conditioning system compressor uses power from the engine when in cooling mode, which will affect the fuel consumption.
Avoiding damage to your vehicle Driving through water Introduction Fig. 153 Maximum permissible water level when driving through water This chapter contains information on the following subjects: Driving Tips Driving through water 134 134 This section of the manual contains important information on preventing damage to the vehicle while driving. Driving Tips Only drive on such roads and in such terrain, which match the vehicle parameters » page 236, Technical data as well as your driving skills.
Assist systems Read and observe on page 135 first. General information The radar sensor » Fig. 154 (From here on referred to as sensor) is used to assess the traffic situation in front of the vehicle. The sensor can distinguish objects by radiating and receiving electromagnetic waves. Introduction This chapter contains information on the following subjects: 135 Radar sensor WARNING The following general information regarding the use of assistance systems must be observed.
Traction control (TCS) Electronic differential lock (EDL and XDS) Driver Steering Recommendation (DSR) Brake Assist (HBA) Hill Start Assist (HHC) Multi collision brake (MCB) Trailer stabilization system (TSA) 136 137 137 137 137 138 138 This chapter describes the functions of the brake and stabilization systems. The error display is in Chapter » page 31, Warning lights. The brake and stabilization systems are automatically activated each time the ignition is switched on, unless otherwise indicated.
During a TCS intervention, the indicator light flashes in the instrument cluster. Activating/deactivating TCS The activation or deactivation of TCS can be done, depending on equipment, in one of the following ways. ▶ Infotainment » Owner´s Manual Infotainment, chapter CAR - vehicle settings. ▶ By briefly pressing the symbol key » Fig. 155. ▶ By briefly pressing the symbol key » Fig. 155.
Multi collision brake (MCB) Read and observe on page 136 first. The MCB helps to decrease speed after a collision through automatic braking interventions and to stabilize the vehicle. This reduces the risk of a subsequent crash due to uncontrolled vehicle movement. The automatic brake interventions can take place only if the following conditions are met. A head-on or side collision occurred. The impact speed was higher than approx. 10 km/h.
Note If the engine stalls while driving and is started again within 30 seconds, then OFF ROAD mode will be automatically activated. Operation Hill Descent Assistant Read and observe and on page 138 first. The hill descent assistant (hereinafter referred to as assist system), with its automatic braking action on all wheels, ensures a constant speed is maintained on a steep slope when driving forwards and reversing. Fig.
Note During an active intervention of the assistant, the brake lights do not light up. ESC OFF ROAD Read and observe on page 138 first. TCSOFF ROAD Read and observe and on page 138 first. Function Display in the Infotainment display Activation / deactivation Automatic system activation when moving forward WARNING The general information relating to the use of assistance systems must be observed » page 135, in section Introduction.
Approximate range of sensors (in cm) Function Area » Fig. 158 Version 1 (4 sensors) Version 2 (8 sensors) Version 3 (12 sensors) A 160 60 - 120 60 160 60 - 120 90 160 90 90 B C D E Fig. 157 Installation position of the sensors on the left side of the vehicle: front/rear Fig. 158 Sampled areas and range of the sensors Audible signals The interval between the acoustic signals becomes shorter as the clearance is reduced. A continuous tone sounds from a distance of approx. 30 cm - danger area.
Display in the Infotainment display Activation / deactivation Fig. 159 Display Read and observe and on page 140 first. Function keys and obstacle warning » Fig. 159 A Road display. Depending on the Infotainment type: Switching off park assistant display. Switching audible parking signals on/off. Change to rear-view camera display . Message: Look! Safe to move? Colour of an object detected in the collision area (the distance to the obstacle is less than 30 cm).
WARNING The general information relating to the use of assistance systems must be observed » page 135, in section Introduction. ■ Make sure that the camera lens is not dirty or covered, otherwise the system function can be significantly impaired. For information on cleaning » page 185, Camera lens Automatic system activation when moving forward ■ Fig.
The area behind the vehicle is displayed when the following conditions are met. The ignition is switched on. Reverse gear is engaged.1) The luggage compartment lid is completely closed. The vehicle is not travelling at more than about 10 km/h. Function buttons » Fig. 163 Turns off the display of the area behind the vehicle. Display settings - brightness, contrast, colour. Switching audible parking signals on/off. Enabling and reduced park assistance display.
The state in which the steering wheel is operated by the system, is referred to as parking operation. The Park Assist is an extension of the parking aid » page 140 and operates on the basis of data collected by the ultrasonic sensors. For this reason, the chapter on the parking aid is to be read carefully and the safety notes are to be observed. WARNING The general information relating to the use of assistance systems must be observed » page 135, in section Introduction.
Parking space search Parking Fig. 164 System button / display Read and observe and on page 145 first. Fig. 165 Display Read and observe and on page 145 first. The system is able to find a parking space in a number of parallel and transverse parked vehicles on the passenger's or driver's side. The system supports the driver when reverse parking in the parking space found in a number of traverse and parallel parked vehicles.
› Depress the brake pedal and wait until the steering wheel automatically rotates into the required position, the symbol goes out. › Carefully drive forwards. › If the backwards arrow is flashing in the display » Fig. 165 - , select reverse gear again or move the selector lever into position R . The display shows the icon (brake pedal). › Depress the brake pedal and wait until the steering wheel automatically rotates into the required position, the symbol goes out. › Carefully move backwards.
The parking process cannot be performed with a trailer or when another accessory is connected to the trailer socket. Time limit exceeded. Take over steering! The parking procedure was ended because the time limit of 6 minutes was passed. Park Assist currently not available. The system cannot be activated because a fault exists on the vehicle. Seek help from a specialist garage.
Operating Description Fig. 168 Cruise control system controls Fig. 167 Segment display: Examples of status displays the CCS Read and observe on page 148 first. CCS status displays » Fig. 166, » Fig. 167 Speed is set, control is inactive (in the colour display the digits of speed limits is shown in grey). Control active (in the colour display the digits of the speed limits are highlighted). No speed set. System fault - seek assistance from a specialist garage immediately.
WARNING For safety reasons, do not use the ACC under the following conditions. ■ When driving in turning lanes, motorway exits or construction sites, to avoid an unwanted acceleration to the stored speed. ■ When visibility is poor, (e.g. fog, heavy rain, thick snowfall). ■ When road conditions are poor (e.g. ice, slippery road, gravel, dirt road). ■ When driving around “sharp” bends. ■ When riding on a steep gradient / high slope.
Note to reduce speed If the delay of the ACC is insufficient in relation to the vehicle in front, in the instrument cluster, the warning light lights up and the display shows the following message. Apply the brake! Note Some ACC notifications in the display of the instrument cluster may be hidden by notifications for other functions. An ACC notification automatically appears for a brief moment when there is a change in status of the ACC. Fig.
Operation Overview On vehicles with a manual transmission, the second gear or higher must be engaged. On vehicles with an automatic transmission, the selector lever must be in the D/S position or in the Tiptronic position. On vehicles with a manual transmission, the current speed must be higher than approx. 25 km/h. On vehicles with a automatic transmission, the current speed must be higher than approx. 2 km/h. The control be started with the key or by adjusting the lever » Fig.
Resume control › Start control » page 152. WARNING Control may only be resumed if the stored speed is not too high for the current traffic conditions. Note Regulation is also stopped when the clutch is held down for longer than 30 s. Set/change the desired speed Read and observe on page 150 first. The desired speed can be set or changed using the control lever » Fig. 171 on page 152. The set speed is stored upon releasing the lever or the button on the button on the lever.
Special driving conditions Narrow vehicles or vehicles travelling side by side Narrow vehicles or vehicles travelling side by side are not detected by the radar sensor until they are within the sensor's range » Fig. 172 - . If necessary, slow down the car by applying the brake. Other vehicles changing lanes Vehicles that change onto the lane with a small proximity » Fig. 173 - do not have to be detected by the radar sensor in time. The result may be a delayed ACC response.
The Front Assist (hereinafter referred to as system) warns you of the danger of a collision with a vehicle or another obstacle in front of the vehicle, and tries to avoid a collision or mitigate its consequences by automatically applying the brakes where necessary. Information messages Read and observe on page 150 first. The information messages are shown in the instrument cluster display. ACC: no sensor view! The area in front of the vehicle is monitored by a radar sensor » page 135.
Distance warning (dangerous distance) Fig. 174 Symbols in the instrument cluster: Note (dangerous proximity) With automatic braking the symbol appears » Fig. 175 in the display. Advance warning If the system detects a risk of collision, the symbol » Fig. 175 appears in the display and you will hear an acoustic signal. At the same time, the braking system is prepared for possible emergency braking. The pre-warning display can occur in the following situations.
The system should only be disabled in exceptional cases » . The system can be activated or deactivated in one of two ways. ▶ In the instrument cluster display » page 48, Menu itemAssist systems. ▶ Infotainment » Owner´s Manual Infotainment, chapter CAR - vehicle settings. The following functions can be activated or deactivated separately in infotainment.
Engine / drive The vehicle acceleration is more dynamic than in Normal mode. Front axle differential lock The driving force distribution between the front wheels is adapted to the sporty driving style. Adaptive Cruise Control (ACC) The acceleration is quicker than in Normal mode with distance control » page 150. Xenon headlight The headlamps adapt to the driving style more dynamically than in mode Normal » page 70. ProActive passenger protection The first level of protection is deactivated » page 160.
Mode selection and Infotainment display Note The currently selected running mode is displayed in the Infotainment in the status bar of the main menu of the symbol . ■ If the driving mode menu is not operated within a few seconds, the Infotainment switches to the last selected menu or switches off. ■ Individual mode settings Read and observe on page 157 first. In mode Individual the vehicle systems can be set as follows.
The first protection level can be deactivated in one of the following ways. system deactivation in the Infotainment » Owner´s Manual Infotainment, chapter CAR - vehicle settings. ▶ Deactivation of TCS » page 136. ▶ Selecting the driving mode Sport » page 157.
When the vehicle approaches a detected line between lanes, the system makes a light movement of the steering wheel in the opposite direction to the boundary line. This corrective steering intervention can be manually overridden at any time. WARNING The general information relating to the use of assistance systems must be observed » page 135, in section Introduction. ■ Lane Assist can help you keep the vehicle within the lane. However, it does not steer the vehicle for you.
The boundary lines are clearly visible (appropriate longitudinal markings). The boundary line of at least one side of the lane is detected. The driver's hands are on the steering wheel. The lane is more than 2.5 m in width. If the turn signal is switched on prior to driving over the boundary line (e.g. when making a turn), no steering intervention takes place when the vehicle approaches the boundary line. The system regards the situation as an intended lane change.
WARNING The general information relating to the use of assistance systems must be observed » page 135, in section Introduction. ■ Vertical traffic signs must always take precedence over the traffic signs shown in the display. The driver is always responsible for correctly assessing the traffic situation. ■ Traffic signs may not be recognised at all by the system, or may be recognised incorrectly. As a result, the traffic signs may not be displayed at all, or the wrong one may appear.
▶ The camera “viewing range” is obstructed by an obstacle. ▶ Travelling at high speed. ▶ The traffic signs are fully or partially obscured (e.g. by trees, snow, dirt or other vehicles). ▶ The traffic signs are not standard (round with a red border). ▶ The traffic signs are damaged or bent. ▶ The traffic signs are attached to flashing neon signs. ▶ The traffic signs were changed (the navigation data are out of date). Additional display Read and observe on page 163 first.
The system detects a break from driving when one of the following conditions is met. ▶ The vehicle is stopped and the ignition is turned off. ▶ The vehicle is stopped, the seat belt is taken off and the driver's door is opened. ▶ The vehicle is stopped for more than 15 minutes. If none of these conditions are met or if the driving style is not changed, the system recommends a driving break again after 15 minutes.
Saving tyre pressure values and infotainment display Fig. 183 Button for storing the pressure values/example of the display: the system indicates a pressure change in the front-right tyre Read and observe on page 165 first. › Inflate all tyres to the prescribed pressure. › Switch on the ignition. › Press and hold » Fig. 184 the symbol key. The warning light lights up in the instrument cluster.
Note Operation and maintenance of the tow hitch » page 186. ■ The towing vehicle by means of the detachable ball rod » page 222. ■ If the towing device is removed completely, it must be replaced with the original reinforcement of the rear bumper which is part of the mount for the towing eye.
12 13 › Turn key A in the direction of arrow 1 so that the red marking is pointing upwards » Fig. 186. Key – Version 1 Key – Version 2 Note If you lose the key, please get in touch with a specialist garage. Adjusting the ready position Gear 1 Step - applies to the key version 2 › Remove the cap from the lock › Insert key B into the lock so that the eye of the key is pointing downwards. › Turn the key in the direction of arrow B 2 so that the conclusions release shows up » Fig. 186.
CAUTION In the ready position, the key cannot be removed nor turned into a different position. Assembling the bar ball – Step 2 Assembling the bar ball – Step 1 Fig. 190 Lock lock: Key Version 1 / key Version 2 Fig. 191 Place cap on the lock Fig. 189 Insert ball rod / trigger bolt in the extended state Read and observe and on page 167 first. Insert ball rod - applies to both key versions › Remove the cover for the mounting recess 4 » Fig. 185 on page 167 in a downwards direction.
CAUTION After removing the key, always replace the cover on the lock – there is a risk of the lock getting dirty. Removing the bar ball – Step 1 Fig. 193 Remove the cap from the lock Check proper fitting Fig. 192 Correctly connected tow bar Read and observe and on page 167 first. Before each use of the ball rod, check that it is attached properly. Correctly secured ball head » Fig. 192 The ball rod does not come off the mounting recess even after strong “shaking”.
WARNING Never remove the tow bar while the trailer is still coupled. Note We recommend putting the protective cover onto the ball head before removing the tow bar. The ball rod is released in this position and falls freely into the hand. If it does not fall freely into the hand, use your other hand to push it upwards. At the same time, the ball rod latches into the ready position and is therefore ready to be re-fitted » . › Place the cap Removing the bar ball – Step 2 Fig. 195 Release ball bar 4 » Fig.
The total permitted weight of the accessory including load changes with increasing distance of the load centre of gravity from the ball head of the towing hitch. Distance of the load centre of gravity from the ball head Permissible total weight of the accessory, including load » Fig.
Exterior mirrors You should have additional exterior mirrors fitted if you are not able to see the traffic behind the trailer with the standard rear-view mirrors. WARNING (Continued) After attaching the trailer and connecting the power socket, check that the rear lights on the trailer are working correctly. ■ Never use the safety eye to tow a vehicle! ■ Headlights The front of the vehicle may lift up when a trailer is being towed and the headlights may dazzle other road users.
Permissible trailer load - Octavia Engine 1.2 l/63 kW TSI 1.2 l/81 kW TSI 1.4 l/81 kW TSI G-TEC 1.4 l/110 kW TSI 1.6 l/81 kW MPI 1.8 l/132 kW TSI 1.6 l/66 kW TDI CR 1.6 l/81 kW TDI CR 2.0 l/105 kW TDI CR 2.0 l/110 kW TDI CR 2.
Engine 2.0 l/169 kW TSI 2.0 l/135 kW TDI CR a) Transmission Permissible trailer load, braked (kg) Gradients of up to 12 % Gradients of up to 8%a) Permissible trailer load, unbraked (kg) MG 1600 1800 720 DSG MG 1600 1600 1800 1800 730 720 DSG DSG 4x4 1600 1800 1800 2000 730 750 Only valid for some countries. Permissible trailer load - Octavia Combi Engine 1.2 l/63 kW TSI 1.2 l/81 kW TSI 1.4 l/81 kW TSI G-TEC 1.4 l/110 kW TSI 1.6 l/81 kW MPI 1.8 l/132 kW TSI 1.6 l/66 kW TDI CR 1.
Engine Transmission Permissible trailer load, braked (kg) Gradients of up to 12 % Gradients of up to 8%a) Permissible trailer load, unbraked (kg) MG 1600 1800 670 2.0 l/110 kW TDI CR MG 4x4 DSG 2000 1600 2000 1800 720 680 2.0 l/135 kW TDI CR DSG 4x4 1800 2000 730 a) Only valid for some countries. Permissible trailer load - Octavia Combi RS Engine 2.0 l/162 kW TSI 2.0 l/169 kW TSI 2.
Brakes Apply the brakes in good time! If the trailer is fitted with a trailer brake, apply the brakes gently at first, then brake firmly. This will avoid brake jolts resulting from the trailer wheels locking. On downhill sections shift down a gear in good time to also use the engine as a brake. WARNING Always drive particularly carefully with the trailer. CAUTION If you tow a trailer frequently, you should also have your vehicle inspected between service intervals.
For the sake of the environment Technical documents regarding changes carried out on the vehicle must be kept by the vehicle user, in order to be handed over to the recyclers later. This ensures that vehicle recycling is in accordance with environmental regulations.
The ŠKODA Service Partners are up-to-date on the legally required tests and will prepare the vehicle for the tests as part of a service operation if required, or will be responsible for carrying out these tests. The specialist garages can carry out the specified tests directly if required by the customer if they are authorised to do so. This saves you time and money.
ŠKODA Service Partners are liable for any defects of ŠKODA Genuine Accessories for a period of 2 years after installation or delivery in accordance with the materials defect liability, unless agreed otherwise in the purchase agreement or any other agreements. You should keep the approved warranty certificate and the invoices for these accessories for this period of time, so that the commencement of the term can be verified.
WARNING No modifications of any kind must be made to parts of the airbag system. Any work on the airbag system including the installation and removal of system components due to other repair work (e.g. removal of the steering wheel) must only be carried out by a specialist garage. ■ Never make any changes to the front bumper or the bodywork. ■ It is prohibited to manipulate individual parts of the airbag system, as this might result in the airbag being deployed.
Clean wheels, door sills and similar parts last. Use a second sponge for such areas. Maintain a sufficiently large distance to the parking aid sensors and soft materials such as rubber hoses or insulation material. Give the vehicle a good rinse after washing it and dry it off using a chamois leather. CAUTION The films should not be washed with any high-pressure cleaners - there is a risk of damage » page 183.
WARNING Vehicle care products may be harmful to your health if not used according to the instructions. ■ Always keep the vehicle care products safe from people who are not completely independent, e.g.
Windows and external mirrors Plastic parts Read and observe and on page 183 first. Fig. 198 Fuel filler flap: Remove ice scraper Clean plastic parts with a damp cloth. If this method does not completely clean the plastic parts, use cleaning products specially designed for this purpose. CAUTION Do not use paint care products on plastic parts. Rubber seals Read and observe and on page 183 first.
CAUTION Information for cleaning windows ■ Do not clean the inside of the windows with sharp-edged objects or corrosive and acidic cleaning agents – there is a risk of damaging the heating elements or window aerial. ■ When drying the windows after washing the vehicle, do not use window leathers that have been used to polish the bodywork. Residues of preservatives in the window leather can dirty the window and reduce visibility. Headlight glasses Read and observe on page 183 first.
Regularly remove salt and brake abrasion, otherwise the rim material will be corroded. Light alloy wheels After washing thoroughly and treat the wheel rims with a protective product for light alloy wheels. For the treatment of wheel rims do not use products which may cause damage to the paint on the rims. CAUTION Damage to the paint layer on the wheel rims must be touched up immediately. ■ Severe layers of dirt on the wheels can also result in wheel imbalance.
WARNING Vehicle care products may be harmful to your health if not used according to the instructions. ■ Always keep the vehicle care products safe from people who are not completely independent, e.g. children - there is a danger of poisoning! ■ Air fresheners and scents can be hazardous to heath when the temperature inside the vehicle is high. ■ CAUTION Be sure to check clothing for colour-fastness to avoid any damage or visible stains on the material (leather), panels and textiles.
Fabric Clean upholstery cover materials and cloth trims on doors, luggage compartment cover, etc. using specific cleaning agents, e.g., dry foam. Use a soft sponge, brush, or commercially available microfibre cloth. Use a cloth and a cleaning agent specifically designed for this purpose to clean the roof trim. Remove any lumps on the cover fabric and any fabric residue using a brush. Remove stubborn hair using a “cleaning glove”.
Petrol and diesel refuelling Inspecting and replenishing Fuel Introduction This chapter contains information on the following subjects: Petrol and diesel refuelling Lead-free petrol Diesel fuel Refuelling with CNG (compressed natural gas) CNG 189 190 191 192 193 The correct fuels for your vehicle are specified on the inside of the fuel filler flap » Fig. 199 on page 189. Fig. 199 Open fuel filler flap/unscrew tank cap/place the tank cap on the fuel filler flap Fig.
› Remove the pump nozzle from the fuel filler tube and put it back in the pump. › Place the filler cap onto the fuel filler neck and turn it in the opposite direction to arrow 3 until it securely engages. › Close the fuel filler flap until it clicks into place. Check that the fuel filler flap is closed properly. Incorrect refuelling guard on vehicles with diesel engines The fuel filler tube on vehicles with diesel engines has been fitted with a incorrect refuelling guard » Fig. 200.
Fuel additives Unleaded petrol in accordance with the EN 228 standard1) meets all the conditions for a smooth-running engine. We therefore recommend that no fuel additives are used. This can result in considerable damage to parts of the engine or the exhaust system. CAUTION Even one filling of the tank with petrol that does not meet the standards can lead to serious damage to parts of the exhaust system! ■ If a fuel other than unleaded fuel which complies to the above mentioned standards (e.g.
Preheating fuel The vehicle is fitted with a fuel filter preheating system. This secures operation of a vehicle using diesel fuel down to an environmental temperature of -24 °C. Diesel fuel additives The diesel fuel in accordance with the prescribed standards meets all the conditions for a smooth running engine. We therefore recommend that no diesel fuel additives are used. This can result in considerable damage to parts of the engine or the exhaust system.
when the engine is restarted. This is not due to any system leakages but a drop in pressure in the natural gas fuel tank due to technical reasons after a cooling phase directly after refuelling. Natural gas quality and consumption Depending on the natural gas supplier, the natural gas quality (heating value) may vary. The engine system adjusts automatically to the natural gas quality. The maximum lifetime of the gas tank is 20 years.
Every 2 years the filler cap. the condition of fuel filler tubes and the sealing ring in the fuel filler tubes, and clean the sealing ring if necessary. ▶ Check the gas system for leaks. ▶ Check ▶ Check Every 4 years the gas tank. ▶ Inspect Every 20 years ▶ Replace the gas tank. WARNING Do not underestimate the smell of gas in the car or when refuelling - risk of fire, explosion and injury. ■ The natural gas tanks in the vehicle must not be exposed to unwanted heat sources.
WARNING (Continued) Never spill operating fluids over the hot engine - risk of fire. If you wish to work under the vehicle, you must secure the vehicle from rolling away and support it with suitable supporting blocks: the car jack is not sufficient for this – risk of injury! ■ ■ CAUTION Always top up using the correct specification of fluids.
WARNING After switching off the ignition, the fan can intermittently continue to operate for approx. 10 minutes. Engine compartment overview Windscreen washer system Fig. 205 Windscreen washer fluid reservoir Fig. 204 Principle sketch: Engine compartment Read and observe and on page 194 first. Layout of the engine compartment » Fig.
CAUTION Under no circumstances must radiator antifreeze or other additives be added to the windscreen washer fluid. ■ If the vehicle is fitted with a headlight cleaning system, only cleaning products which do not attack the polycarbonate coating of the headlights must be added to the windscreen washer fluid.
CAUTION In an emergency, another engine oil to be refilled. To prevent damage to the engine, a maximum of 0.5 litres only of the following engine oils may be used: ■ For petrol engine models: ACEA A3/ACEA B4 or API SN, (API SM); ■ For diesel engine models: ACEA C3 or API CJ-4. ■ The engine consumes a little oil. The oil consumption may be as much as 0.5 l/1000 km depending on your style of driving and the conditions under which you operate your vehicle.
The coolant additive percentage in the coolant must be at least 40%. The coolant additive may be increased to a maximum of 60%. The correct mixing ratio of water and coolant additive is to be checked if necessary by a specialist garage or is to be restored if necessary. The description of the coolant is shown in the coolant expansion reservoir » Fig. 207 on page 199. WARNING The engine compartment of your car is a hazardous area.
Checking the level › Check the coolant level in the coolant expansion tank » Fig. 207. WARNING The engine compartment of your car is a hazardous area. The following warning instructions must be followed at all times when working in the engine compartment » page 194. ■ Do not use used brake fluid - the function of the brake system may be impaired – risk of accident! ■ If the engine is warm, the test result may be inaccurate. The level can also be above the mark A » Fig. 207.
A slight drop in the fluid level results when driving due to normal wear-andtear and automatic adjustment of the brake pads. There may be an indication of a leak in the brake system, however, if the fluid level drops significantly within a short time or if it drops below the “MIN” marking. Too low brake fluid level is indicated by the warning light being shown on the display of the instrument cluster as well as the corresponding message » page 32.
WARNING The use of open flames and light should be avoided. Smoking and radio triggering activities should be avoided. Never use a damaged vehicle battery – risk of explosion! Never charge a frozen or thawed vehicle battery – risk of explosion and caustic burns! ■ Replace a frozen vehicle battery. ■ Never jump-start vehicle batteries with an electrolyte level that is too low – risk of explosion and caustic burns. ■ ■ ■ ■ CAUTION ■ Improper handling of the vehicle battery may cause damage.
Winter time The vehicle battery only has a proportion of the starting power in lower temperatures. A discharged vehicle battery may already freeze at temperatures just below 0 °C. We therefore recommend that you have the battery checked and, if necessary, recharged by a specialist garage before the start of the winter. Note The battery acid level is also checked regularly by a specialist garage as part of the inspection service. Charging Read and observe and on page 201 first.
› Firstly disconnect the battery's negative terminal , followed by the positive terminal . Connecting › Firstly connect the battery's positive terminal , followed by the negative terminal . After disconnecting and re-connecting the vehicle battery, the following functions or devices are partially or completely inoperative.
Wheels Always store wheels or tyres in a cool, dry and, where possible, dark place. Tyres which are not fixed to a wheel trim should be stored upright. Tyres and wheel rims Tyre age Tyres age losing their original characteristics, even if they are not used. The service life of the tyres is 6 years. Therefore, we recommend not using tyres that are more than 6 years old.
Tyre diameter in inches These details are intended only as information for the specified tyre pressure and does not list approved tyre sizes for your vehicle. The approved tyre sizes for your vehicle are listed in the vehicle's technical documentation (COC document) and this also states the declaration of conformity. The approved tyre diameter for your vehicle is also provided with the vehicle data » page 236.
Tyre wear indicator and wheel replacement Tyre damage Read and observe on page 205 first. We recommend checking your tyres and wheel rims for damage (punctures, cuts, splits and bulges, etc.) on a regular basis. Remove any foreign objects in the tyre tread immediately (e.g. small stones). Foreign bodies which have penetrated into the tyre (e.g. screws or nails) should not be removed and seek help from a specialist garage. Fig.
In vehicles with tyre pressure monitoring, save tyre pressure values » page 165. WARNING If, you get a puncture and a spare tyre has to be mounted with opposite direction of rotation, then drive carefully. The tyre no longer retains its optimal characteristics in this situation. ■ If the dimensions or design of the spare wheel differ from the tyres fitted to the vehicle (e.g.
Speed symbol Maximum speed (in km/h) S T U H V W Y 180 190 200 210 240 270 300 WARNING Never exceed the maximum permissible load bearing capacity of mounted tyres. ■ Never exceed the maximum permissible speed for the mounted tyres. ■ On vehicles with the infotainment system with key the speed limit can be set for winter tyres » Owner´s Manual Infotainment, chapter CAR - Adjust vehicle systems.
Octavia RS a) Rim size Impression depth D Tyre size 6J x 17a) 6J x 17a) 45 mm 48 mm 205/50 R17 205/50 R17 Only fit snow chains with links and locks not larger than 12 mm. Remove the full wheel trims before fitting the snow chains » page 213. CAUTION The chains must be removed when driving on snow-free roads. They would otherwise cause loss of performance and damage the tyres.
Warning triangle – version 1 The warning triangle can be attached to the rear wall trim panel with rubber straps » Fig. 213 - . Natural gas vehicles have the warning triangle located under the floor mat in the luggage compartment. Do-it-yourself Emergency equipment, and self-help Warning triangle – version 2 The warning triangle can be secured with straps in the right storage compartment in the luggage compartment » Fig. 213 - .
Vehicle tool kit Fire extinguisher Fig. 215 Fire extinguisher The fire extinguisher is attached by two straps in a holder underneath the driver's seat. Removing/attaching › Loosen the two straps by pulling the buckles in the direction of the arrow » Fig. 215. › Remove the fire extinguisher. › To fit in place, insert the fire extinguisher back into the bracket and secure with straps. Please read the instructions which are attached to the fire extinguisher.
CAUTION Screw the jack back into the starting position before storing in the box with the vehicle tool kit. ■ Ensure that the vehicle tool kit is safely secured in the luggage compartment. ■ Ensure that the box is always secured with the strap. ■ Note The declaration of conformity is included with the jack or the log folder. › For vehicles with manual transmission select 1st gear. › On vehicles with automatic transmission, place the selector lever in the P position. › The parking brake switch.
Extracting › Hook the clamp found in the vehicle tool kit » page 212 into the reinforced edge of the wheel trim. › Push the wheel wrench through the clamp, support on the tyre and pull off the wheel trim. Installing › Press the wheel trim onto the wheel rim at the designated valve opening. › Then press the trim into the wheel rim until its entire circumference locks correctly in place. Notes on wheel trims supplied at the factory or from ŠKODAOriginal Accessories.
Note Note down the code number located on both the adapter and also on the end of each anti-theft wheel bolt. This number can be used to purchase a replacement adapter from ŠKODA Genuine Parts if required. ■ The anti-theft wheel bolt set and adapter can be purchased from a ŠKODA Partner. ■ Raising the vehicle Loosening/tightening wheel bolts Fig. 220 Changing a wheel: Loosening the wheel bolts Fig.
Raising the vehicle › Insert the crank 7 into the mount on the jack 6 » page 212. › Support the base plate of the jack with its entire surface resting on level ground and ensure that the lever is positioned vertically to the jacking point » Fig. 222. › Use the crank to raise the jack until its claw encloses the bar » Fig. 222. › Continue to raise the jack until the wheel is just lifted off the ground.
Puncture repair kit Components of the puncture repair kit Introduction This chapter contains information on the following subjects: Components of the puncture repair kit General information Preparations for using the breakdown kit Sealing and inflating the tyre Notes for driving with a repaired tyre 217 218 218 218 219 Use the breakdown kit to reliably repair tyre damage caused by foreign bodies or a puncture with diameters up to approx. 4 mm.
General information Read and observe Sealing and inflating the tyre on page 217 first. For your own safety and the safety of your passengers, the following instructions must be observed before carrying out a wheel repair on the road. Switch on the hazard warning light. Place the warning triangle at the prescribed distance. Park the vehicle as far away as possible from flowing traffic. Choose a location with a flat, solid surface. Have all the occupants get out.
WARNING If the tyre cannot be inflated to at least. 2.0 bar, the damage is too great. The sealing agent cannot be used to seal the tyre. Do not drive the vehicle. Seek help from a specialist garage. ■ The tyre inflation hose and air compressor may get hot as the tyre is being inflated – risk of burning. ■ CAUTION Switch off the air compressor after running 8 minutes at the latest – risk of overheating! Allow the air compressor to cool a few minutes before switching it on again.
Fig. 225 Engine earth: START-STOP system Read and observe on page 219 first. The starting process using the battery of another vehicle requires the use of jumper cables. The jump-start cables must be attached in the following sequence. › Attach clamp 1 to the positive terminal of the discharged battery A » Fig. 224 . › Attach clamp 2 to the positive terminal of the battery supplying power B . › Attach clamp 3 to the negative terminal of the battery supplying power B .
Vehicles with automatic transmission may be towed in with a tow bar or a tow rope or with the front wheels raised. If the vehicle is raised at rear, the automatic gearbox is damaged! If possible, the vehicle should be towed with the engine running or at least with the ignition on. Driver of the tow vehicle › Engage the clutch gently when starting off or depress the accelerator particularly gently if the vehicle is fitted with an automatic gearbox. › Only then approach correctly when the rope is taut.
Removing/installing the towing eye › Manually screw the towing eye as far as it will go in the direction of the arrow 3 » Fig. 227 » . For tightening purposes, we recommend, for example, using the wheel wrench, towing eye from another vehicle or a similar object that can be pushed through the eye. › Unscrew the towing eye against the direction of the arrow 3. WARNING The towing eye must always be screwed in fully and firmly tightened, otherwise the towing eye can tear when towing in or tow-starting.
› Insert the new battery. › Insert the battery cover Remote control Introduction Synchronising the remote control This chapter contains information on the following subjects: Replacing the battery in the remote control key Synchronising the remote control replace battery in the remote control the auxiliary heating (auxiliary heating) 223 223 223 CAUTION We recommend having faulty rechargeable batteries replaced by a ŠKODA service partner.
Emergency unlocking/locking Locking the door without a locking cylinder Introduction This chapter contains information on the following subjects: Unlocking/locking the driver's door Locking the door without a locking cylinder Unlock the boot lid Selector lever-emergency unlocking 224 224 224 225 Unlocking/locking the driver's door Fig.
› Open the boot lid. Replacing the windscreen wiper blades Selector lever-emergency unlocking Fig. 236 Windscreen wiper blade Fig. 235 Selector lever-emergency unlocking › Firmly apply the handbrake. › Open the stowage compartment in the front centre console » page 91. › Grab hold of the cover A in the area of the arrows and carefully raise it forwards in the direction of the arrow 1 and then backwards » Fig. 235. › Use a finger to press the yellow plastic part in the direction of the arrow 2 .
Replacing the rear window wiper blade Fuses and light bulbs Fuses Introduction This chapter contains information on the following subjects: Fig. 237 Rear window wiper blade Read and observe on page 225 first. Removing the wiper blade › Lift the wiper arm from the window in the direction of 1 » Fig. 237. › Tilt the wiper blade to the stop in the same direction. › Hold the upper part of the wiper arm and press the securing mechanism A in the direction of arrow 2 .
WARNING Always read and observe the warnings before completing any work in the engine compartment » page 194. CAUTION “Never repair” fuses, and do not replace them with fuses of a higher amperage – risk of fire! This may also cause damage at other points in the electrical system. ■ If a newly inserted fuse blows again after a short time, have the electrical system checked as quickly as possible by a specialist garage. ■ A blown fuses is recognisable by the molten metal strip.
› Insert a new fuse. › Replace the bracket at the original position. Installing the storage compartment B of the storage compartment behind the brackets C » Fig. 239. › Push in the storage compartment in the opposite direction of the arrow 5 . › Insert the brake rod and lock it against the arrow 4 with a screwdriver. › Push in the side cover against the direction of the arrow 2 . › Press the side cover fully against the direction of the arrow 1 . › Close the storage compartment.
No.
No.
Note This Owner's Manual only describes the replacement of bulbs where it is possible to replace the bulbs on your own without any complications arising. Other bulbs must be replaced by a specialist garage. ■ We recommend that a box of replacement bulbs always be carried in the vehicle. Replacement bulbs can be purchased from ŠKODAOriginal Accessories. ■ Replacing the low beam bulb Bulb arrangement in the headlights Fig. 243 Principle sketch: Headlights Fig.
Change bulb for long-distance, daytime running lights and parking light switch Fig. 245 Bulbs for main beam, daytime running lights, and parking light › Grasp the lamp socket at the places marked by arrows. › Remove the faulty bulb from the holder in the direction of the arrow 2 . › Insert a new bulb in the bulb holder up to the stop. › Replace the bulb holder in the headlamp with the bulb. › Insert the protective cap B » Fig. 243 on page 231 and turn it in the direction opposite to the arrow.
Replacing the light bulb › Press the latch on the connector in the direction of arrow 5 . › Remove the key in the direction of the arrow 6 . › Pull the lamp holder until it stops in the arrow direction 7 . › Remove the lamp holder in the direction of the arrow 8 . › Insert the new bulb into the headlight and turn counter to the direction of arrow 7 as far as the stop. › Fit the connector. Refit the headlight and grille › Replace the fog light by inserting it in the opposite direction of the arrow 4 » Fig.
› Push in the lamp in the direction of the arrow › Insert into opening 1 » Fig. 249. The lamp comes loose. › Swivel out the lamp in the direction of the arrow 2 and remove it. › Remove the faulty bulb from the holder in the direction of the arrow › Insert a new bulb into the holder. › Reinsert the lamp in the opposite direction to the arrow 1 . › Push on the light until the spring clicks into place. Check that the light is securely inserted. 3. A 1)» Fig.
Replacing bulbs in the rear light - Variant 1 › Turn the respective light bulb » Fig. 252 until it stops counter-clockwise and remove it from the bulb holder. › Insert a new bulb into the holder and turn in a clockwise direction to the stop. › Insert the bulb holder in the tail lamp assembly. › Screw on the lamp holder carefully. Replacing bulbs in the rear light - Variant 2 Fig. 251 Outer part of the light: Basic light/light with LED diodes Fig.
Vehicle characteristics Technical data Technical data Basic vehicle data Introduction This chapter contains information on the following subjects: Vehicle characteristics Operating weight Payload Measurement of fuel consumption and CO2 emissions according to ECE Regulations and EU Directives Dimensions - Octavia Dimensions - Octavia estate Track gauge front/rear Departure angle 236 237 238 239 240 241 242 243 The details given in the vehicle's technical documentation always take precedence over the
10 11 Maximum permissible front axle load Maximum permissible rear axle load Vehicle identification number (VIN) The vehicle identification number - VIN (vehicle body number) is stamped into the engine compartment on the right hand suspension strut dome. This number is also located on a sign on the lower left hand edge below the windscreen (together with a VIN bar code), and on the type plate.
Engine Transmission Operating weight (kg) MG DSG 1445 1465 MG DSG 1445 1465 DSG 4x4 1550 Transmission Operating weight (kg) MG MG DSG MG MG (EU5) MG (EU6) DSG (EU4, EU5) DSG (EU6) MG AG MG (EU4, EU5) MG (EU6) DSG 4x4 DSG (EU4, EU5) DSG (EU6) MG MG5 MG6 MG 4x4 DSG MG DSG 1247 1252 1277 1416 1272 1277 1287 1292 1232 1272 1337 1342 1450 1352 1357 1327 1327 1280 1435 1342 1347 1367 2.0 l/169 kW TSI 2.0 l/135 kW TDI CR Warning triangle – Octavia Combi Engine 1.2 l/63 kW TSI 1.2 l/81 kW TSI 1.
Measurement of fuel consumption and CO2 emissions according to ECE Regulations and EU Directives The data on fuel consumption and CO2 emissions were not available at the time of going to press. The data on fuel consumption and CO2 emissions are given on the ŠKODA websites or in the sales and technical vehicle documentation. The measurement of the intra-urban cycle begins with a cold start of the engine. Afterwards urban driving is simulated.
Dimensions - Octavia Fig. 255 Vehicle dimensions Vehicle dimensions for operating weight without driver (in mm) » Fig. 25 Specification 5 A B C D E F G H a) b) c) Basic dimensions Vehicles with off-road package Vehicles with SPORT package Front track » page 242 Width Rear track » page 242 Width including exterior mirror Basic dimensions Clearance Vehicles with off-road package Vehicles with SPORT package Basic dimensions Wheel base Vehicles with 1.
Dimensions - Octavia estate Fig. 256 Vehicle dimensions Vehicle dimensions for operating weight without driver (in mm) » Fig. 256 Specification A B C D E F G H a) b) c) Basic dimensions Vehicles with off-road package Vehicles with SPORT package Front track » page 242 Width Rear track » page 242 Width including exterior mirror Basic dimensions Clearance Vehicles with off-road package Vehicles with SPORT package Basic dimensions Wheel base Vehicles with 1.
Track gauge front/rear Engine Front track Rear track 1.2 l/63 kW TSI 1.2 l/81 kW TSI 1.4 l/81 kW TSI G-TEC 1.4 l/110 kW TSI 1.6 l/81 kW MPI 1.8 l/132 kW TSI 2.0 l/162 kW TSI 2.0 l/169 kW TSI 1.6 l/66 kW TDI CR 1.6 l/81 kW TDI CR 2.0 l/105 kW TDI CR 1549 1549 1543 1543 1549 1543/1538a) 1535 1535 1549 1549 1543 1520 1520 1515 1514 1520 1512/1506a) 1506 1506 1520 1520/1518b) 1514 1543/1538a) 1535/1538a)/1543b) 1514/1506a)/1512b) 1506/1512b) 2.0 l/110 kW TDI CR 2.
Departure angle Angle » Fig. 257 A Overhang angle, front B Overhang angle, rear Overhang angle The values shown indicate the maximum incline of an embankment, up which the vehicle can drive at a slow speed without collision of the bumper or underbody. The values listed correspond to the maximum axle load, front or back. Fig. 257 Departure angle: Octavia/Octavia Combi Departure angle (°) - Octavia Octavia » Fig.
Vehicle-specific information depending on engine type Introduction This chapter contains information on the following subjects: 1.2 ltr. / 63 kW TSI engine 1.2 ltr. / 81 kW TSI engine 1.4 l/81 kW TSI G-TEC engine 1.4 ltr./110 kW TSI engine 1.6 l/81 kW MPI engine 1.8 l/132 kW TSI engine 244 244 245 245 245 246 2.0 l/162 kW TSI engine 2.0 ltr./169 kW TSI engine 1.6 ltr./66 kW TDI CR engine 1.6 ltr./81 kW TDI CR engine 2.0 l/105 kW TDI CR engine 2.0 ltr./110 kW TDI CR engine 2.0 ltr.
1.4 l/81 kW TSI G-TEC engine Output (kW/rpm) Maximum torque (Nm at rpm) Number of cylinders/displacement (cm3) Body Transmission Top speed (km/h) Acceleration 0-100 km/h (s) 81/4800-6000 200/1500-3500 4/1395 Octavia MG 195 10.9 Octavia Estate MG 193 11 1.4 ltr./110 kW TSI engine Output (kW/rpm) Maximum torque (Nm at rpm) Number of cylinders/displacement (cm3) Body Transmission Top speed (km/h) Acceleration 0-100 km/h (s) 110/5000-6000 250/1500-3500 4/1395 Octavia MG 219 8.1 Octavia Estate DSG 219 8.
1.8 l/132 kW TSI engine Output (kW/rpm) Maximum torque (Nm at rpm) Number of cylinders/displacement (cm3) Body Octavia 132/5100-6200 (132/4500-6200)a) 250/1250-5000 (280/1350-4500)a) 4/1798 Octavia Estate Transmission MG DSG DSG 4x4 MG DSG DSG 4x4 Top speed (km/h) Acceleration 0-100 km/h (s) 231 7.3 231 7.4 229 7.4 229 7.4 229 7.5 227 7.5 a) DSG 4x4 Scout 216 7.8 Applies to 4x4 vehicles. 2.
1.6 ltr./66 kW TDI CR engine Output (kW/rpm) Maximum torque (Nm at rpm) Number of cylinders/displacement (cm3) Body Transmission Top speed (km/h) Acceleration 0-100 km/h (s) 66/2750-4800 230/1400-2700 4/1598 Octavia MG 186 12.2 Octavia Estate MG 183 12.3 1.6 ltr./81 kW TDI CR engine Output (kW/rpm) Maximum torque (Nm at rpm) Number of cylinders/displacement (cm3) Body Transmission Top speed (km/h) Acceleration 0-100 km/h (s) 81/3200-4000 250/1500-3000 4/1598 MG5 197 10.6 MG6 206 10.
2.0 ltr./110 kW TDI CR engine Output (kW/rpm) Maximum torque (Nm at rpm) Number of cylinders/displacement (cm3) Body Transmission Top speed (km/h) Acceleration 0-100 km/h (s) a) 110/3500-4000 320/1750-3000 (340/1750-3000)a) 4/1968 Octavia Estate Octavia MG MG 4x4 DSG MG MG 4x4 218 8.5/8.4a) 215 8.5 215 8.6/8.5a) 216 8.6/8.5a) 213 8.6 MG 4x4 Scout 207 9.1 DSG 213 8.7/8.6a) Applies to cars with the EU6 emission standard. 2.0 ltr.
Index A abroad lead-free petrol 190 Abroad Headlights 74 ABS Operation 136 Warning light 34 ACC 150 Control symbol 32 Warning lights 40 Acceptance and recycling of used vehicles 181 Accessories 178 Adaptive cruise control automatic stop-start 151 Information messages 155 Operation 150 Operation Overview 152 Set/change the desired speed.
Avoiding damage to your vehicle 134 B Bags on the backs of the front seats Ball head Check fitting Ready position Ball rod Ready position Battery In the remote control key Belts Belt tensioners Bonnet Closing Opening Boot Class N1 vehicles See Boot lid Boot lid automatic locking Closing Opening Brake information messages warning light Brake Assist (HBA) Brake booster brake fluid specification Brake fluid Checking information messages Brake linings warning light Brake pedal (automatic transmission) Warning
Clean Anodized parts Chrome parts Cleaning Alcantara and maintaining belts artificial leather headlight glasses materials natural leather plastic parts seats covers of the electrically heated seats wheels Cleaning safety belt Cleaning seat covers Cleaning the interior artificial leather Seat covers Cleaning the vehicle exterior Camera lens Cavity protection Decorative films Door locking cylinder Headlight glasses Protective films Under-body protection wheels Windows and external mirrors Cleaning vehicle Cle
Disconnecting and reconnecting vehicle battery Display Compass points Coolant temperature Gear changes Natural gas reserve Petrol / Diesel reserve Service interval Disposal Acceptance and recycling of used vehicles Distance driven Distance warning Warning light Door Child safety lock Closing Emergency locking Emergency locking the driver's door Opening Door warning double hooks Drive Driving through water DriveGreen Driver Steering Recommendation (DSR) Driving Emissions Fuel consumption through water Drivin
Fog lights 72 Warning light 36 80 Fold in passenger's mirror Footmats 128 see footmats 128 Force limit Electric boot lid 60 Power windows 63 Sliding/tilting roof 65 Front airbag 15 Front Assist 155 Disable/enable 156 Distance warning 156 157 Information messages Operation 155 Radar sensor 135 Warning and automatic braking 156 Warning light 40 Front door warning light 75 fuel lead-free petrol 190 Fuel 189 CNG 193 Diesel 191 Natural gas reserve display 30 Petrol / Diesel reserve display 30 refer to Fuel 189 1
Temperature gauge Warning lights Interior care Natural leather Interior light Front Interior lights Rear Interior monitor iPad holder Behind the headrests Handling ISOFIX 29 31 186 187 74 75 58 99 99 23 J Jack Maintenance Jump-starting 212 185 219 K KESSY Locking Unlocking Key Locking Starting the engine Stopping the engine Switching off the ignition Switching on the ignition Unlocking Key CAR see Infotainment Knee airbag 55 55 54 121 121 121 121 54 4 17 L Lamp failure Warning light Lamps Warning ligh
Luggage compartment lid Luggage net Luggage storage Multi-function pocket 59 104 107 M Main beam Warning light Maintenance see vehicle care Manual air conditioning Air distribution control Controls Manual gear changing see gear changing Manually adjusting seats Manually adjusting seats MAXI DOT display Lap timer Main menu Menu item assist systems Menu item Audio Menu item navigation Menu item telephone Operation Stop watch MAXI DOT see MAXI DOT display Maximum permissible weights MCB Mechanical window lif
P Park assist Departing from a parallel parking space 147 Information messages 147 Parking 146 Park Assist 144 Automatic brake assist 147 145 Operation Parking space search 146 Parking 128 Park Assist 144 Parking aid 140 Rear View Camera 143 140 Parking aid Automatic system activation when moving forward 143 Function 141 Parking assistance Activation / deactivation 142 Display in the Infotainment display 142 Parking lights 68 Park Pilot 140 Park the vehicle see Parking 128 Part replacement 178 Passive safet
Reversing camera Lens care Revolutions counter Roller blind Luggage compartment cover Roof Load Roof rack mounting points Roof load Stowing in the luggage compartment Rubber seals Running-in Brake linings Engine Tyres 185 29 105 112 110 111 112 111 184 132 132 132 S SAFE See Safe securing system SAFELOCK See Safe securing system Safe securing system Safety Child safety Child safety seats Correct seated position Head restraints ISOFIX TOP TETHER Saving electrical energy Saving fuel Seals Vehicle care Seat
START-STOP 124 Jump-starting 219 Manually deactivating/activating the system 126 operation 125 Warning light 39 START-STOP system 124 Starter button Problems starting the engine 124 Starting the engine 123 Steering column lock locking 122 Steering column lock unlocking 122 Switching off the engine 123 Switching off the ignition 123 Switching on the ignition 123 Starting and stopping the engine at the push of 122 the button Starting and stopping the engine using the key 120 Starting engine Jump-starting 219
Trailer operation 167, 176 138 Trailer stabilization system (TSA) Transmission Warning messages 37 Transport Luggage compartment 100 Roof rack 110 Transporting 89 Transporting children safely 20 TSA 138 Turn signal 69 Turn signal system Warning light 36 Tyre 208 Explanation of the label see wheels 208 Tyre load-bearing capacity see Wheels 208 Tyre pressure 205 Warning light 35 Tyre pressure monitoring 165 Display 35 Infotainment display 166 Saving tyre pressure values 165 Saving tyre pressure values - butto
Visibility Visors see front sun visors see Sun screen 76 76 77 W Warning indicator of a low temperature Warning light Warning lights Warning symbols see Warning lights Warning triangle warning when speeding Washing Automatic car wash system by hand High-pressure cleaner Washing vehicles Waste container Water in the fuel filter Warning light warning messages Weather conditions Wheel bolts Anti-theft wheel bolts Caps Loosening and tightening Wheel rims Wheels Age of wheels Changing Driving style Full trim G
Index 261
262 Index
Reprinting, duplicating, translating and any other use, either in whole or in part, is not permitted without the written consent of ŠKODA AUTO a.s.. ŠKODA AUTO a.s. expressly reserves all rights relating to copyright laws. Subject to change. Issued by: ŠKODA AUTO a.s. © ŠKODA AUTO a.s.
www.skoda-auto.com Návod k obsluze Octavia anglicky 11.
