SIMPLY CLEVER OWNER´S MANUAL ŠKODA Yeti
5L0012720AM
Preface You have opted for a ŠKODA – our sincere thanks for your confidence in us. This Owner's Manual contains instructions about the vehicle operation, important information about safety, vehicle care, maintenance and self-help and technical vehicle data. For vehicles with Infotainment, the operation of some of the functions and vehicle systems is carried out via Infotainment. Please do not read just this Owner's Manual, but also read the Infotainment Owner's Manual carefully.
Table of Contents materials defect liability and ŠKODA warranty for new cars 4 On-board literature 6 Notes 7 Structure of the Owner's Manual and further information 8 Abbreviations Safety Passive Safety General information Correct and safe seated position 10 10 10 Seat belts Using seat belts Inertia reels and belt tensioners 13 13 15 Airbag system Description of the airbag system Airbag deactivation 16 16 19 Transporting children safely Child seat Fastening systems 21 21 24 Using the system
Brake fluid Vehicle battery Wheels Wheels and tyres Operating in winter conditions 147 147 150 150 152 Do-it-yourself 154 154 155 159 161 162 Emergency equipment and self-help Emergency equipment Changing a wheel Breakdown kit Jump-starting Towing the vehicle Remote control and removable light replacing the battery/batteries Emergency unlocking / unlocking of doors Replacing windscreen wiper blades 164 165 166 Fuses and light bulbs Fuses Bulbs 167 167 170 Technical data Technical data Basic vehicle d
materials defect liability and ŠKODA warranty for new cars Materials defect liability Your ŠKODA Partner, as a vendor, is liable to you for material damage to your new ŠKODA car, ŠKODA Genuine Parts or ŠKODA Genuine Accessories in accordance with statutory regulations and the purchase agreement.
▶ Parts fitted on or in the vehicle, whose use has not been approved by ŠKODA AUTO, or modification of the vehicle in a manner not approved by ŠKODA AUTO (e.g. tuning). ▶ Damage caused by you that was not immediately seen to by a specialist garage or was not rectified properly. Note The ŠKODA extended warranty is only available in some countries. It is the customer's responsibility to prove that s/he is not the cause of the damage.
On-board literature You will always find this Owner's Manual in the on-board literature. Depending on equipment fitted, the on-board literature can also contain the Infotainment Owner's Manual or The radio Owner's Manual. Online user manuals Fig. 1 On-board literature online on the ŠKODA web pages Owner´s Manual These Owner´s Manual apply to all body variants of the vehicle and all related model versions as well as all equipment levels.
Notes Terms used “Specialist” - Workshop - a workshop that carries out specialist service tasks for ŠKODA vehicles. A specialist can be a ŠKODA Partner, a ŠKODA Service Partner, or an independent workshop. “ŠKODA Service Partner” - A workshop that has been contractually authorised by ŠKODA AUTO or its sales partner to service ŠKODA vehicles and to sell ŠKODA Genuine Parts.
Structure of the Owner's Manual and further information Structure of the Owner's Manual The Owner's Manual is hierarchically divided into the following areas. ■ Section (e.g. Operating instructions) - the title of the section is shown down in the left-hand corner ■ Main chapter (e.g. Checking and refilling) - the title of the main chapter is shown down in the right-hand corner ■ Chapter (e.g.
Abbreviations Abbreviation Definition Abbreviation Definition Nm Newton meter, measuring unit for the engine torque PIN personal identification number rpm Engine revolutions per minute ABS Anti-lock brake system AF Multi-purpose vehicles AFS Adaptive headlights TSA AG Automatic gearbox TSI Petrol engine with turbo charging and direct injection AGM Vehicle battery type VIN Vehicle identification number SCR TDI CR TCS Traction control W CO2 Carbon dioxide Wi-Fi COC Declaration
▶ Protect children using a suitable child seat » page 21, Transporting children safely. ▶ Adopt the correct seated position. Tell your passengers to assume the correct seated position » page 10, Correct and safe seated position.
WARNING The front seats and all head restraints must be adjusted to match the body size at all times and the seat belt must always be fastened properly to provide the most effective levels of protection to the passengers. ■ Each occupant must correctly fasten the seat belt belonging to the seat. Children must be fastened » page 21, Transporting children safely with a suitable restraint system.
› Adjust the steering wheel to the desired position. The steering wheel can be adjusted in direction of arrow 2 . › Pull the holder in arrow direction 3 until the stop. WARNING Never adjust the steering wheel when the vehicle is moving only when the vehicle is stationary! ■ The safety lever must always be locked so that the steering wheel cannot accidentally change position – There is a risk of an accident! ■ Correct seating position for the front passenger Read and observe on page 11 first.
Seat belts Using seat belts Introduction This chapter contains information on the following subjects: Correct routing of seat belt Fastening and unfastening seat belts Seat belt for the rear middle seat 14 14 15 Seat belts that are fastened correctly offer good protection in the event of an accident. They reduce the risk of an injury and increase the chance of survival in the event of a major accident. The seat belts reduce the kinetic energy (energy of motion) to a considerable extent.
Correct routing of seat belt Seat belt height adjusters for front seats › Push the return pulley upwards in the direction of arrow » Fig. 5 - . › Or: push together the mechanism in the direction of arrows 1 and push the return pulley downwards in the direction of arrow 2 » Fig. 5 - . › Then pull firmly on the belt to ensure that the seat belt height adjuster has correctly locked in place. WARNING Always ensure that the webbing of the seat belts is properly routed.
› Insert the lock tongue into the belt buckle » Fig. 6 – that is part of the seat until it clicks into place. › Pull on the belt to check that it has engaged correctly in the lock. Release › Grip the lock tongue and press the red button in the buckle » Fig. 6 - , the lock tongue pops out. › Guide the belt back by hand so that the seat belt does not twist and the webbing rolls up fully. WARNING The slot of the belt tongue must not be blocked otherwise the belt tongue will not lock in place properly.
WARNING Any work on the belt tensioner system, including the removal and installation of system components because of other repair work, must only be carried out by a specialist garage. ■ If the belt tensioners have been deployed, it is then necessary to replace the entire system. ■ Note The belt tensioners can also be deployed if the seat belts are not fastened. Smoke is generated when the belt tensioners are deployed. This is not an indication of a fire in the vehicle.
D E Rear side airbags Head airbags Airbag deployment Front airbags - the forward thrust of the driver and of the front passenger is cushioned when they make contact with the fully-inflated airbag, and the risk of injury to head and chest is thus reduced. The front airbags can be identified by the lettering featured on the steering wheel and on the dashboard on the passenger side.
The following airbags will be deployed in the event of a severe side collision. ▶ Front side airbag. ▶ Rear side airbag. ▶ Head airbag. When an airbag is deployed, the following events occur. ▶ The hazard warning lights are switched on. ▶ All doors are unlocked. ▶ The fuel supply to the engine is interrupted. ▶ The interior light comes on (if the automatic operation of the interior light is switched on - position ).
WARNING Information about for side and head airbags ■ No objects (e.g. sun visors turned towards the windows) should be located in the deployment area of the side and head airbags. No accessories (e.g. cup holders etc.) should be fitted to the doors - There is a risk of an injury! ■ Hang only light clothing on the hooks in the vehicle, do not leave any heavy or sharp objects in the pockets. Do not use hangers to hang up the clothes.
Deactivating the front passenger airbag WARNING The key cannot be inserted into the key switch while driving. Shocks can cause the key to turn in the slot and trigger the airbag! The airbag can be triggered unexpectedly in an accident - it may result in injury or death! ■ The driver is responsible for whether the airbag is switched on or switched off. ■ Only switch off the airbag when the ignition is switched off! Otherwise a fault can occur in the system for deactivating the airbag.
Transporting children safely Child seat Introduction To reduce the risk of injury in an accident, children should only be transported in child seats! This chapter contains information on the following subjects: Use of a child seat on the front passenger seat Use of a child seat on the front passenger seat Child safety and the side airbag Classification of child seats Use of child safety seats which are secured using a seat belt WARNING (Continued) Children are exposed to an increased risk of injury in
Use of a child seat on the front passenger seat Does not apply to Taiwan Adjust the height of the front passenger seat belt so that the belt does not “jam” in the return pulley. In the event of an accident, there is the risk of injury to the neck of the child carried due to the seat belt! WARNING Never use a rear-facing child seat on the front passenger seat if the passenger airbag is activated. This child safety seat is positioned in the deployment area of the front passenger airbag.
Classification of child seats Child safety and the side airbag Fig. 13 Incorrect seated position of a child who is not properly secured – risk from the side airbag/Child properly protected by safety seat Read and observe Read and observe on page 21 first. Classification of child seats according to the ECE-R 44 standard. Group Weight of the child 0 0 1 2 3 up to 10 kg up to 13 kg 9-18 kg 15-25 kg 22-36 kg on page 21 first.
Fastening systems is a system for securing child seats quickly and safely. There are two fixing eyes between the seat backrest and the seat cushion of the front passenger seat for fixing a child seat with the system.
Group Size class of the child seata) Front passenger seatb) Outer rear seats Rear seat middle 1 9-18 kg D C B B1 A X IL-SU IUF X - X IL-SU X - X IL-SU X 2 15-25 kg 3 22-36 kg a) b) The size category is shown on the label attached to the child seat. If the front passenger seat is fitted with system attachment points, it is suitable for the installation of an child seat with “Semi-Universal” approval.
Fig.
24 Using the system Cockpit 25 Overview 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Door opening lever Electric exterior mirror adjustment Air outlet vents Ticket holder Operating lever (depending on equipment): ▶ Direction and high beam ▶ Speed regulating system Steering wheel with horn / with driver's front airbag Buttons for operating the information system Instrument cluster Operating lever: ▶ Windscreen wipers and washers ▶ Information system Warning light for the front passenger
▶ Instruments and Indicator Lights Instrument cluster 4 Introduction 5 6 7 Displaying the distance and days until the next service interval1) » page 44 ▶ Show AdBlue range1) » page 39 Coolant temperature gauge » page 29 Display » page 38 Fuel gauge » page 29 Operation key: ▶ Reset counter for distance travelled (trip) » page 38 ▶ Setting the time ▶ Enable / disable the mode selected using the 3 button Rev counter The tachometer 1 » Fig. 17 on page 28 shows the actual engine speed per minute.
Coolant temperature gauge Fig. 18 Coolant temperature gauge WARNING For the vehicle systems to function correctly, and thus for safe driving, there must be sufficient fuel in the tank. Never drain the fuel tank completely – risk of accident! CAUTION Never drive until the fuel tank is completely empty! Irregular supply of fuel can cause misfiring, which can result in damage to parts of the engine and the exhaust system. The display » Fig. 18 only works if the ignition is switched on.
If too much water is present in the separator, the following information appears on the instrument cluster display. Auto Check Control Vehicle condition Certain functions and conditions of individual vehicle systems are checked continuously when the ignition is switched on. If there is a system failure, the relevant message is displayed in the MAXI DOTDisplay, in conjunction with indicator lights, if necessary, indicator light illumination takes place in the instrument cluster» page 31, Warning lights.
WARNING If you have to stop for technical reasons, then park the vehicle at a safe distance from the traffic, switch off the engine and switch on the hazard warning light system » page 61. Place the warning triangle at the prescribed distance. Note If the MAXI DOT display shows warning messages, these messages must be confirmed in order to access the main menu » page 40 . ■ As long as the operational faults are not rectified, the warning lights are always indicated again.
Handbrake Read and observe on page 31 first. lights up – the hand brake has been applied. An acoustic signal will sound if you drive the vehicle above 6 km/h while the handbrake is still on. ▶ Release the handbrake. Read and observe on page 31 first. illuminates – the brake fluid level in the brake system is too low. ▶ Park the vehicle, stop driving! Seek help from a specialist garage.
Power steering / steering lock (KESSY system) Read and observe on page 31 first. Fault in the power steering lights up – this indicates a complete failure of the power steering and the steering assist is no longer working (significantly higher steering forces). lights up – this indicates a partial failure of the power steering and the steering forces can be greater. ▶ Switch off the ignition, start the engine again and travel a short distance.
Stability control (ESC) / Traction control (TCS) Read and observe on page 31 first. If your vehicle is equipped with the ESC system, the TCS is part of the ESC system. flashes – the ESC or TCS is currently active. System fault lights up – there is an ESC or TCS fault. ▶ Continued driving is possible with appropriate caution. Seek assistance from a specialist garage immediately. If the warning light comes on after starting the engine, the TCS may be switched off for technical reasons.
Emission control system Read and observe on page 31 first. Diesel particle filter (diesel) Read and observe on page 31 first. lights up – there is a fault in the emission control system. The system makes it possible to drive on in emergency mode - there may be a noticeable reduction in engine performance. The diesel particulate filter separates the soot particles from the exhaust. The soot particles collect in the diesel particulate filter where they are burnt on a regular basis.
An audible signal sounds as a warning. Fuel reserve Read and observe on page 31 first. illuminates – the fuel level in the fuel tank is at the reserve level (approximately 9 litres). An audible signal sounds as a warning. ▶ Please refuel » page 139. Note The text in the display goes out after refuelling and driving a short distance. Read and observe on page 31 first. System fault lights up - there is a fault in the airbag system. Error: Airbag ▶ Seek help from a specialist garage.
Windscreen washer fluid level Read and observe on page 31 first. flashes – the hill descent assistant is engaged at the moment. Main beam illuminates – the windscreen washer fluid level is too low. ▶ Top lights up – the main beam or the headlight flasher is switched on. up the windscreen washer fluid » page 144. Turn signal system Read and observe on page 31 first. flashes – the left turn signal is turned on. flashes – the right turn signal is turned on.
Information system 5 Driver information system 6 Introduction 7 This chapter contains information on the following subjects: Display in the instrument cluster Setting the time Display of the second speedometer Display of AdBlue range Gear recommendation Display in the instrument cluster 38 39 39 39 39 8 9 10 Door alarm Service interval display Outside temperature Total distance travelled Speed regulating system Distance travelled by resetting the memory (trip) Engaged gear / gear recommendation S
Setting the time Fig. 22 Buttons in the instrument cluster MAXI DOT display The display of AdBlue range is part of the multi-function display » page 41, Information overview. Segment display › Press button A » Fig. 22 on page 39 repeatedly until instead of total kilometres travelled, the AdBlue Range is displayed. › Wait around 5 seconds - the system switches to the initial setting. Gear recommendation Use buttons A and B to set the time» Fig. 22. A The choice to change the display (hours or minutes).
- Recommends that you change down to a lower gear On vehicles with a manual gearbox, the recommended gear and an arrow symbol is displayed (e.g. means that it is advantageous to change up from a lower gear to 4. gear). ▶ On vehicles with an automatic gearbox in manual shifting mode (Tiptronic), gearcurrently engaged and an arrow symbol is displayed, (e.g. means that it is advantageous to change up from 4 to a higher gear).
AdBlue® range - drive distance in km which can be covered with the existing AdBlue®tank capacity and with the same driving style. If you drive more efficiently this value can increase. Multifunction display (MFD) Introduction Distance driven - distance driven since the memory was last cleared.
Memory MAXI DOT display Fig. 26 Multi-function display - memory display Introduction This chapter contains information on the following subjects: Menu itemNavigation Menu itemAudio Menu itemPhone Menu itemAssistants Menu item Settings The system stores data from the two memories described below, which are then displayed at position A » Fig. 26. “1” - Single-trip memory Drive data is stored from when the ignition is switched on to when it is switched off.
Menu itemAudio The following information is displayed in the Audio menu item. Radio ▶ Currently playing station (name/frequency). ▶ The selected frequency range (e.g. FM) optionally with the number of the station button (e.g. FM 3), if the station is stored in the memory list. ▶ List of available stations (if more than 5 stations can be received). ▶ TP traffic announcements. Media ▶ Name of the track being played, if necessary, further information regarding title (e.g.
Travel mode Factory setting. Information regarding the service intervals » page 133. Activate/deactivate the travel mode feature» page 62. Prompt in the MAXI DOT display Resetting Lights & Visionmenu item to the factory setting. Coasting -Enable / disable the idle position (coasting) for vehicles with automatic transmission » page 108, Driving in neutral (“coasting”). Time - Setting the time, the time format (24 or 12 hour) and the change-over to summer/winter time.
Messages before reaching the scheduled service date Before the next service date has been reached, the symbol» Fig. 27 as well as a message about the mileage or days until the next service event appears in the display for approx. 10 seconds after switching on the ignition.
connection to SmartGate using Wi-Fi This type of connection is intended for external devices running Android and iOS operating systems. Connecting to an Android external device › Switch on the ignition. › Switch on Wi-Fi in the external device that is to be connected and search for available Wi-Fi networks (see Owner's Manual for the external device). › In the menu of the detected networks, select the “SmartGate_...”1) menu item.
SmartGate web interface Unlocking and opening SmartGate parameters can be set in the SmartGate web interface. The following address must be entered in the web browser of the external device that is connected with SmartGate. HTTP://192.168.123.1 Introduction This chapter contains information on the following subjects: The setting changes are only effective after tapping the buttons “Save” → “Reboot”.
WARNING Never leave the key in the vehicle when you exit the vehicle. Unauthorised persons (e.g. children) could lock the car, turn on the ignition or start the engine - There is risk of injury and accidents! ■ When leaving the vehicle, never leave people who are not completely independent, such as children, unattended in the vehicle. These individuals might not be able to exit the vehicle by themselves or to help themselves.
If the boot lid is closed after locking the vehicle and the key with which the vehicle was locked remains in the luggage compartment, the lid is automatically unlatched (partially opened). After automatically unlocking, the turn signal lights will flash four times. The boot lid remains unlatched (partially opened); the other doors remain locked. Unlocking/locking - KESSY CAUTION Some types of gloves can affect the unlocking or locking device via the sensors in the door handle.
All doors The function allows you to unlock all doors, the boot lid and the fuel filler flap. SafeLock Read and observe and on page 48 first. SafeLock prevents opening the doors from inside as well as window operation. This makes an attempted break-in to the vehicle more difficult. Activating SafeLock is activated when the vehicle is locked from the outside. This function is pointed out by the following message on the display of the instrument cluster after the ignition is switched off.
› To open from the inside pull the door opening lever B and push the door away from you. › To the lock from the inside, grab the handle C and close the door.
CAUTION Before leaving the vehicle, it must be checked that all of the windows, doors and the sliding/tilting roof are locked in order to ensure the full functionality of the anti-theft alarm system. Note The alarm system has its own power source, whose service life is 5 years. Alarm trigger Read and observe on page 52 first. The alarm is triggered when one of the following unauthorised actions is activated on the vehicle with an activated warning system. ▶ Opening the bonnet. ▶ Opening the boot lid.
Opening / closing the boot lid Window operation Introduction This chapter contains information on the following subjects: 54 54 54 55 55 55 Mechanical windows Electric window Opening the windows in the front passenger door and in the rear doors Force limiter Window convenience operation Operational faults Fig. 36 Opening / closing tailgate Read and observe on page 52 first. › To open the lid, press-- --» Fig. 36 button A in the direction of arrow 1.
D Mechanical windows E Right rear door Deactivate/activate the buttons in the rear doors (the deactivation may be advantageous if, for example, children are transported on the rear seats) › To open, lightly press the appropriate button and hold it until the window has moved into the desired position. › or: press the button to the stop, the window automatically opens fully. Renewed pressing of the button causes the window to stop.
› or: press the buttonunderneath to the stop, the window automatically opens fully. Renewed pressing of the button causes the window to stop. › To open, lightly press the button above and hold it until the window has moved into the desired position. › or: press the buttonabove to the stop, the window automatically opens fully. Renewed pressing of the button causes the window to stop. › Or Switch off the ignition, open the driver's door and hold the key A until it stops in the open position » Fig.
Panorama sliding/tilting roof Operation Introduction This chapter contains information on the following subjects: Operation Force limiter Convenience operation of sliding / tilting roof Activate operation of the tilt / slide sunroof Sunshade with electric operation Activating operation of the sunshade 56 56 57 57 57 57 The panoramic tilt / slide sunroof (hereinafter referred to as tilt / slide sunroof) can only be operated when the ignition is turned on and when the outdoor temperature is above -20
WARNING If the tilt / slide sunroof is closed, by pulling on the recess of the switch in the direction of arrow 2 , » Fig. 40 on page 56 and the closing process is hindered by an obstacle, then at the third attempt at closing, the force limitation will cease to function (if less than 5 s passes between the individual attempts to close). The tilt / slide sunroof closes with full force - There is a risk of injury. Sunshade with electric operation Fig.
Operating the lights Lights and visibility Lights Fig.
Note If, with a low beam, the ignition is turned off, then the dipped beam will automatically switch off 1) and the parking lights illuminate. The parking lights are switched off when the ignition key is removed (for vehicles with the KESSY system, after opening the driver's door). ■ If there is a fault in the light switch, the low beam comes on automatically. ■ Turn signal and main beam Fig.
Automatic driving light control Fig. 44 Light switch: AUTO position WARNING If there is a system malfunction the headlights are automatically lowered to the emergency position, which prevents a possible dazzling of oncoming traffic. This reduces the cone of light in front of the vehicle. Seek help from a specialist garage. Fog lights/rear fog light Read and observe Fig. 45 Light switch: Switch on fog lights / rear fog light on page 58 first. The light switch is in position » Fig.
Fog lights with the CORNER function Read and observe Hazard warning light system on page 58 first. Fig. 46 Button for hazard warning light system The CORNER function automatically switches on the fog lights on the respective side of the vehicle (e.g. when cornering), if the following conditions are fulfilled. The turn signal is switched on or the front wheels are turned sharply 1). The vehicle speed is below 40 km/h. The low beam is switched on. The fog lights are not switched on.
Switching on the side light on both sides › Switch on the ignition and turn the light switch to position» page 58, the parking lights are turned on. › Switch off the ignition and lock the car. Front interior light After pulling out the ignition key and opening the driver's door, an audible warning sounds. After a few seconds or after closing the driver's door, the audible warning is turned off. CAUTION Turning on the parking light means the battery is heavily loaded.
Windscreen and rear window heating Interior lighting, rear Fig. 48 Interior lights at the rear Operation (by moving the lens A ) » Fig. 48 Switching on Automatic operation (centre position) 1) Switching off Fig. 49 Buttons for rear and front window heating: Manual air conditioning / Climatronic The heating only works when the engine is running.
Front sun visors Windscreen wipers and washers Introduction This chapter contains information on the following subjects: Windscreen wipers and washers Rear windscreen wipers and washers Headlight cleaning system 65 65 66 The windscreen wipers and the wash system only operate if the ignition is switched on and the bonnet and boot are closed1). WARNING Do not use the windscreen washer system at low temperatures, without heating the windscreen beforehand.
Note Each time the ignition switches off for the third time, the position of the windscreen wipers changes. This counteracts an early fatigue of the wiper rubbers. ■ The windscreen washer nozzles for the windscreen are heated when the engine is running and the outside temperature is less than +10 °C. ■ Windscreen wipers and washers Fig. 51 Operating the windscreen wipers and washer system Read and observe and WARNING Automatic wiping during rain is only a support.
Headlight cleaning system Read and observe and Interior mirror dimming on page 64 first. The headlights are cleaned with every first and after every fifth spraying of the windscreen under the following conditions. The ignition is switched on. The low beam is switched on. The outside temperature is about -12° C to +39° C. To ensure the correct functioning of the system, even in winter, this needs to be regularly cleared of snow and ice (e.g. using the de-icing spray). Fig.
Mirrors Fig. 54 Exterior mirror operation Manual folding mirrors The mirror can be manually folded in towards the side window. To put it back into its original position, it should be folded back from the side window until it audibly clicks into place. Folding-in both of the exterior mirrors using the remote control key › Close all windows and hold the button on the remote control key. The exterior mirror is folded back into the driving position when the ignition is switched on.
CAUTION Never manually fold in/out the electrically folding exterior mirrors - there is a risk of damage to the mirror! ■ When the mirror is swung by external influences (due to impact during manoeuvring, for example), then first fold-in the mirror by turning the knob and wait for a loud clapping noise.
Adjusting the tilt of the backrest (do not lean on the backrest when adjusting) D Setting the extent of the curvature of the lumbar support C Note After a certain time, play can develop within the adjustment mechanism of the backrest angle. Note If the inclination angle of the seat backrest relative to the seat surface is greater than 102 °, then it is not possible for safety reasons to save this setting in the memory of the electrically adjustable seats or the remote control key.
Retrieving the saved setting The retrieval is possible when turned the ignition is switched on and the vehicle speed is less than 5 km/h or when the ignition key is inserted in the ignition lock. › Hold the desired memory button B » Fig. 57 . Stopping the ongoing adjustment › Press any button on the driver's seat or the button on the remote control key.
Folding the seat backrest forwards and folding the seat fully forwards Unlock and removing the seat Adjusting seats in crosswise direction Folding back seats WARNING (Continued) Do not adjust the seat back while driving - There is a risk of injury and accidents! ■ When moving the seat backrest, keep limbs out of the area between the seat and seat backrest – risk of injury! ■ Never transport the following items on the seat backrest when folded forwards. ■ Objects that could restrict the driver's view.
Folding the seat backrest forwards and folding the seat fully forwards › Secure the folded forward seat with the aid of the fixing belt B to a guide rod of the head restraint in the front seat » Fig. 63. WARNING The seat backs in occupied rear seats must be properly engaged. When transporting objects in the luggage compartment that has been enlarged by folding the backrest forward, ensure the safety of the passengers transported on the other rear seats.
Note The outer seats are not mutually interchangeable. In the rear area the left seat is marked with the letter L and the right seat with the letter R. › Press the lever in direction of arrow rest in the direction of arrow 2. 1 » Fig. 66 and fold back the seat backCheck this by pulling on the seat backrest. Headrests Adjusting seats in crosswise direction Fig.
The seat heating only operates when the engine is running. Removing/installing WARNING If you are sensitive to pain and/or temperature, e.g. through medication, paralysis or because of chronic illness (e.g. diabetes), we recommend not to use the seat heating. If the seat heating is used, we recommend to make regular breaks in your journey when driving long distances, so that the body can recuperate from the stress of the journey. Please consult your doctor, who can evaluate your specific condition. Fig.
Useful features Interior fittings Introduction This chapter contains information on the following subjects: Ticket holder Storage compartment on the dash panel stowage compartments in the doors Storage compartment in the front centre console USB and AUX input Cup holders Cigarette lighter Ashtray 12-volt socket Waste container Multimedia holder Storage compartment under the front arm rest storage net in the front centre console Glasses compartment Storage compartment on the front passenger side Storage
Storage compartment on the dash panel Fig. 71 Opening the storage compartment Read and observe and on page 75 first. Storage compartments » Fig. 72 A Storage compartment B Bottle holder with a capacity of max. 1 l C Bottle holder with a capacity of max. 0.5 l WARNING The storage compartment A » Fig. 72 is to be used exclusively for storing objects which do not stick out - There is a risk of restricting the effectiveness of the side airbags. Read and observe and on page 75 first.
Cup holders USB and AUX input Fig. 74 AUX input: underneath the armrest / above the storage compartment Fig. 76 Cup holders: in the front centre console / on the folding table in the centre backrest Fig. 75 USB input Read and observe and on page 75 first. Fig. 77 Cup holders in the rear centre console: Open / Adjust size Depending on equipment fitted, the AUX input is located below the armrest » Fig. 74 - or above the storage compartment » Fig. 74 - .
WARNING Do not use any cups or beakers which are made of brittle material (e.g. glass, porcelain). This could lead to injuries in the event of an accident. ■ Never put hot beverage containers in the cup holder. If the vehicle moves, they may spill – There is a risk of scalding! Ashtray ■ CAUTION Do not leave open beverage containers in the cup holders during the journey. There is a risk of spilling e.g. when braking which may cause damage to the electrical components or seat upholstery.
Rear ashtray - low centre console › To open, grasp the lid on the edge C and fold in the direction of arrow 1 until the stop » Fig. 79. › To remove, grasp the ashtray at the handle D and remove in direction of arrow 2 . › To use Insert the ashtray in the console away from arrow 2 and push in. › Connect the plug for the electrical appliance to the socket. WARNING Do not place anything on the dashboard.
Closing takes place in reverse order. Waste container Replace bags › Remove the waste container from the slot. › Press the two locking lugs on the frame in the direction of arrow 1 » Fig. 83. › Pull the bag together with the frame down in the direction of arrow 2 . › Remove the bag from the frame. › Pull the new bag through the frame and pull it over the frame in the direction of arrow 3 .
Storage compartment under the front arm rest storage net in the front centre console Fig. 86 Storage net Fig. 85 Open storage compartment / open air supply Read and observe and on page 75 first. Storage compartment › To open, lift the armrest in the direction of arrow A » Fig. 85. › To close, lift the armrest in the direction of arrow A until the stop and then fold down against the direction of the arrow A . Read and observe and on page 75 first. The storage nets» Fig.
Storage compartment on the front passenger side Read and observe and on page 75 first. The storage compartment under the passenger seat is used for storing an umbrella. › To open, pull the handle in direction of arrow 1 pull and open the compartment in the direction of arrow 2 » Fig. 89. › To close, screw in the lid in the opposite direction of arrow 2 until it audibly clicks into place. CAUTION Never store a wet umbrella in the storage compartment - there is a risk of damage to the umbrella. Fig.
WARNING Never leave any heavy or sharp-edged objects in the pockets of the items of clothing hung up - There is a risk of injury. ■ Do not use hangers to hang up the clothes - there is a risk of restricting the effectiveness of head airbags and a danger of injury from the hanger. ■ Make sure that any clothes hanging from the hooks do not impede your vision. ■ › To close, swivel the compartment against the direction of the arrow.
Folding table on the middle seat backrest Fig. 94 Middle seat backrest already folded forward Read and observe and on page 75 first. After folding forwards,the centre seat backrest can be used as an armrest or table with cup holders » Fig. 94. CAUTION If the middle rear seat backrest should be folded forward for lengthy periods, then make sure that the belt locks are not located below it - this can warp the upholstery or fabric.
Attaching the rear headrests Handle holder Fig. 96 Inserting: Adapter / Holder Fig. 98 Tilt and rotate holder Fig. 99 Adjust holder size Fig. 97 Removing: Holder / Adapter Read and observe on page 84 first. › To insert, attach the opened adapter to the guide rods of the front headrest and clip in the direction of arrow 1 » Fig. 96 » . › Clip the holder in the direction of arrow 2 into the adapter.
WARNING Never exceed the maximum permissible load of the respective fasteners, nets, hooks etc.
Fastening elements Read and observe and on page 86 first. Fastening examples for nets » Fig. 101 A Horizontal pocket B Floor net C Vertical pocket The maximum permissible load of each of the nets is 1.5 kg. Multifunction pocket Fig. 102 Securing the multifunction pocket Fig. 100 Fasteners: Version 1/version 2 Read and observe and on page 86 first. The fasteners are located on both sides of the luggage compartment. Overview of the fastening elements » Fig.
Fastening bar with sliding hook Flexible storage compartment Fig. 104 Flexible storage compartment Fig. 103 Sliding hook onto the mounting bar / removing hook Read and observe and on page 86 first. A fastening bar is located on both sides of the luggage compartment with two moveable hooks each, in order to attach small items of luggage, such as bags, etc. The maximum permissible load of each of the hooks is 7.5 kg. Moving the hook › Fold up the hook in direction of arrow 1 » Fig.
Luggage compartment cover WARNING Do not place any objects on the cover during the trip - there is a risk of injury if braking suddenly or colliding! Net partition Fig. 105 Remove the luggage compartment cover Read and observe and on page 86 first. If the support straps A » Fig. 105 are attached to the boot lid, then opening the lid will raise the boot lid cover (hereafter referred to as cover).
› Put the net partition folded together in the bag and close it. › Attach the bag with the aid of the plastic carabines to the eyes on the left Removable storage box and right boot trim panel. Fig. 108 Storage box Installing and removing the net partition behind the rear seats with variable loading floor is carried out in the same way as behind the rear seats without variable loading floor. Use the lower fixing eyelets on the carrier rails in order to attach the carabines.
Lamp charges The lamp is supplied by three rechargeable type NiMH AAA batteries. The batteries are charged continuously with the engine running (to fully charge the battery takes approximately 3 hours). Replace batteries » page 164. CAUTION The light is not waterproof, so it must be protected from humidity - otherwise there is risk of damage. Fig. 110 Removable light: Removing / Inserting Read and observe and on page 86 first.
Removing/fitting variable loading floor Fig. 111 Fold up / removal variable loading floor › To fold together, grasp the variable loading floor on handle A and lift in the direction of arrow 1 » Fig. 111. › Fold up the variable loading floor in direction of arrow 2 . › Pull on both sides of the locking levers in direction of arrow 3 . › Remove the variable loading floor in direction of arrow 4 . Insertion takes place in reverse order. Secure the variable loading floor in the raised position Fig.
The sides of the variable loading floor can be folded in the direction of arrow » Fig. 114 - . Heating and ventilation The room under the variable loading floor » Fig. 114 - can be used to stow the load. Heating, manual air conditioning system, Climatronic Transportation on the roof rack Roof load The maximum permitted weight of the load incl. carriers is 100 kg. WARNING The following instructions must be observed to aid road safety when transporting cargo on the roof rack.
WARNING The blower should always be on to prevent the windows from misting. Otherwise there is a risk of accident. ■ Under certain circumstances, air at a temperature of about 5 °C can flow out of the vents when the cooling system is switched on. ■ Note The air inlet in front of the windscreen must be free of e.g. ice, snow or leaves to ensure that the heating and cooling system operates properly.
Adjust the blower speed ▶ Increase speed ▶ Decrease speed Switching the airflow to the windscreen on and off Air flow to the windows Air flow to the upper body Air flow in the footwell Switch the automatic recirculation on/off » page 96 Switch on/off the rear window heater » page 63 Switching automatic mode on » page 95 Switch the Climatronic system off Switching the cooling system on/off Switch the temperature setting in Dual mode on/off When the function is switched on,
Air distribution control Read and observe on page 94 first. The recirculation mode prevents contaminated outside air getting into the interior of the vehicle. In recirculated air mode air is sucked out of the interior of the vehicle and then fed back into the interior. Heating and manual air conditioning system › To switch on press thebutton. › To switch off, press the button again.
Note The air outlet vents 6 » Fig. 118 are only fitted on vehicles with the higher centre console. Auxiliary heating (auxiliary heating and ventilation) Introduction This chapter contains information on the following subjects: Switch on / off System settings Remote control Fig. 118 Air vents at the rear Read and observe on page 94 first. The direction of airflow can be adjusted using the air outlet vents 3, 4 » Fig. 117 and 6 » Fig. 118 – the outlets can be opened and closed individually.
Note The aux. heating only switches the blower on, if it has achieved a coolant temperature of approx. 50 °C. ■ In the engine compartment, water vapour may form during the operation of the aux. heating. ■ Switch on / off After switching off the system, the coolant pump and the aux. heating will continue running a little while longer in order to burn the remaining fuel in the heating.
Display warning light B Remote control Fig. 120 Radio remote control Lights up orange for 2 seconds, then green or red. Lights up orange for 2 seconds, then flashes green or red. Flashes orange for 5 seconds. Read and observe and Meaning The battery is weak, however the switching on or off signal was received. The battery is weak, however the switching on or off signal was not received. The battery is discharged, however the switching on or off signal was not received.
Note Do not warm up the engine while the vehicle is stationary. If possible, start your journey as soon as the engine has started. Through this, the engine reaches its operating temperature faster.
Starting engine › On vehicles with ignition lock, turn the key to position 3 and the engine starts» Fig. 121 on page 101 . Then release the key, the engine will start automatically. Switch on/off ignition If the engine does not start within 10 seconds, turn the key to position 1 . Repeat the start-up process after 30 s. › On vehicles with starter button, press the button briefly » Fig. 121 on page 101 - , the motor will start automatically.
Note The engine running noises may be louder at first for a short time after starting the cold engine. ■ You should not switch on any major electrical components during the heating period, otherwise the vehicle battery will be drained unnecessarily. ■ After switching off the ignition, the radiator fan may (also intermittently) continue to operate for approx. 10 minutes.
Requirements for the system to function correctly The following conditions must be met for the system to function correctly. The driver's door is closed. The driver has fastened the seat belt. The driving speed was higher than 4 km.h after the last stop. No trailer or other accessory is connected to the trailer socket. System status The system status is indicated in the instrument cluster display when stopped.
The wear and tear on the brake pads is dependent on the operating conditions and driving style. In difficult conditions (e.g. urban, sporty driving), the condition of the brakes should be checked between services by a specialist garage. Brake response can be slower if the brakes are covered in moisture or, in winter, have a layer of ice or salt on them. The brakes should be cleaned and dried by applying the brakes many times over » .
A warning signal sounds if the vehicle is inadvertently driven off with the handbrake applied. The handbrake warning is activated if the vehicle is driven at a speed of over 5 km/h for more than 3 seconds. WARNING Disengage the handbrake completely. A handbrake which is only partially disengaged can result in the rear brakes overheating.
CAUTION If not in the process of changing gear, do not leave your hand on the gearshift lever while driving. The pressure from the hand can cause the gearshift mechanism to wear excessively. Pedals The operation of the pedals must not be hindered under any circumstances! Only a floor mat (ex-factory or from the ŠKODA Original Accessories range) which can be secured to the attachment points should be used in the driver's footwell.
D S Driving forwards - In mode D, the forward gears are automatically changed according to the engine load, accelerator pedal actuation and driving speed Sports mode - the gear change takes place in the position S at higher engine speeds than in mode D Before changing to mode S from mode D, press the lock button in the direction of arrow 1 » Fig. 128 on page 107. Note To switch the selector lever from mode P to mode D/S or vice versa, move the selector lever quickly.
Starting-off and driving Read and observe and Running in and economical driving on page 106 first. Moving off and pausing temporarily › Firmly depress and hold the brake pedal. › Start the engine. › Press the locking button and move the selector lever to the desired position » page 106. › Release the brake pedal and accelerate. The selector lever position N does not have to be selected when stopping for a short time (e.g. at a crossroads).
Avoiding damage to your vehicle Driving through water Introduction Fig. 130 Maximum permissible water level when driving through water This chapter contains information on the following subjects: Driving Tips Driving through water 109 109 Driving Tips Only drive on roads and terrain that are appropriate to the vehicle parameters » page 175, Technical data. The driver is always responsible for deciding whether the vehicle can cope with the conditions and the terrain.
WARNING The general information relating to the use of assistance systems must be observed » page 110, in section General information. Assist systems General information WARNING The assistance systems only serve to support and do not relieve the driver of the responsibility for driving the vehicle.
Traction control (TCS) Electronic Differential Lock (EDL) Read and observe on page 110 first. EDL prevents the turning of the respective wheel of the driven axle. EDL brakes a spinning wheel if required and transfers the drive power force to the other drive wheel. Driving becomes easier on road surfaces with different traction under each wheel of the driven axle. EDL switches off automatically to avoid excessive heat generation on the brake of the wheel being braked.
The HHC is active on gradients upwards up 5% if the driver door is closed. HHC is only ever active on slopes when in forward or reverse start off. WARNING The general information relating to the use of assistance systems must be observed » page 110, in section General information. ■ A lack of fuel can cause irregular engine running or cause the engine to shut down.
The following functions are integrated in the OFF ROAD mode. 113. ▶ Downhill Drive Support » page ▶ TCS OFF ROAD » page 113. ▶ EDL OFF ROAD » page 113. ▶ ABS OFF ROAD » page 113. ▶ Start-Off Assistant » page 114. Note If the engine stalls while driving and is started again within 30 seconds, then OFF ROAD mode will be automatically activated. Read and observe and WARNING For the correct operation of the assistant the road surface must be sufficiently adherent.
The system is only available, if the front wheels are in the straight-ahead position. WARNING (Continued) External noise sources may affect the signals of the system sensors. There is a danger that obstacles may not be recognised by the system sensors. ■ Before reversing, you should satisfy yourself that there are no small obstacle, such as a rock, thin post etc., in front or behind your vehicle. Such obstacles may not be recognised by the system sensors. ■ The system operates at speeds of up to 50 km/h.
Fig. 134 Sampled areas and range of the sensors Note If with Version 3 vehicles not all fields around the vehicle are active after activation the vehicle should be moved forwards or backwards. ■ The signal tones for front obstacle recognition are factory-set to be higher than for rear obstacle recognition. ■ The sound of the park-assist can be adjusted via the MAXI DOT display in the Assistants menu option » page 43. ■ Display in the Infotainment display Read and observe and on page 114 first. Fig.
Activation / deactivation Reversing camera Fig. 136 System key (option 2, 3) Introduction This chapter contains information on the following subjects: Operation Guidelines and function keys 117 117 The rear view camera (hereinafter referred to as system) helps the driver when parking and manoeuvring by displaying the area behind the vehicle in the Infotainment display (hereinafter referred to as display).
Operation Guidelines and function keys Fig. 137 Installation location of the camera / scanned area behind the vehicle Read and observe and on page 116 first. The camera for capturing the area behind the vehicle is in the grip of the boot lid » Fig. 137. Area behind the vehicle » Fig. 137 A Detection range of the camera B Area outside the detection range of the camera The system can assist the driver when parking and manoeuvring under the following basic conditions. The ignition is switched on.
WARNING The general information relating to the use of assistance systems must be observed » page 110, in section General information. ■ During the parking process, the system automatically performs rapid steering movements. While it is doing so, do not place your hands between the steering wheel – risk of injury! ■ During a parking manoeuvre on loose or slippery surfaces (gravel, snow, ice, etc.) you may stray from the calculated road.
▶ The display shows instructions and information before the start and during the parking. ▶ Based on the calculated road surface, the front wheels will be automatically rotated during the parking. Conditions for the system function The system can look for a parking space only if the following basic conditions are met. The system is activated. The vehicle is travelling at less than 40 km/h. The vehicle is travelling at less than 20 km/h.
› Depress the brake pedal and wait until the steering wheel automatically ro- Parking tates into the required position, the symbol goes out. › Carefully drive forwards. › If the backwards arrow is flashing in the display - , select reverse gear again or move the selector lever into position R. The display shows the icon (brake pedal). › Depress the brake pedal and wait until the steering wheel automatically rotates into the required position, the symbol goes out. › Carefully move backwards.
The Cruise Control System (CCS) maintains a set speed without you having to actuate the accelerator pedal. The state where the CCS maintains the speed is referred to hereinafter as the control. Automatic brake assist Read and observe and on page 118 first. Automatic brake assist when speeding If a velocity of 7 km / h is exceeded during the parking manoeuvre for the first time, the speed will be automatically reduced by the system to less than 7 km / h.
Operation description Fig. 141 Cruise control system controls Note During control, speed can be increased by pressing the accelerator pedal. Releasing the accelerator pedal will cause the speed to drop again to the set speed. Fatigue detection The fatigue detection system (hereinafter referred to as system) recommends the driver takes a break from driving when driver fatigue can be detected due to the driver's steering behaviour. Read and observe on page 121 first.
Note In some situations, the system may evaluate the driving incorrectly and thus mistakenly recommend a break (e.g. sporty driving, adverse weather conditions or poor road conditions). ■ The system is designed primarily for use on motorways. ■ Tyre pressure monitoring Fig. 142 Key for storing the pressure values WARNING The general information relating to the use of assistance systems must be observed » page 110, in section General information.
Description Towing device and trailer Hitch Introduction This chapter contains information on the following subjects: Description Setting the ready position Check the setting of the standby position Assemble the ball rod Check proper mounting Removing ball rod - Step 1 Removing ball rod - Step 2 Vertical load with mounted accessories 124 125 125 125 126 126 127 127 The maximum trailer nose weight when towing a trailer is 80 kg, for vehicles with four-wheel drive and the 2.0 l / 103 kW TDI CR or 2.
Setting the ready position Read and observe on page 124 first. Correctly adjusted standby position » Fig. 145 The locking balls A can be pushed fully into the tow bar. The red marking B on the hand wheel is located in the green box on the tow bar. The key C is in the unlocked position and cannot be removed. There is a clear gap of approx. 5 mm D between the hand wheel and the tow bar. When in the ready position, the key cannot be removed from the lock.
Check proper mounting Fig. 148 Correctly secured ball head Fig. 147 Locking the lock and removing the key/replacing the lock cap Read and observe on page 124 first. › Grip the cap on the rear bumper B » Fig. 146 at the handle A , release in the direction of the arrow 1 and remove in the direction of the arrow 2 . › Remove the cover for the mounting recess 4 » Fig. 143 on page 124 in a downwards direction. › Adjust the ball rod to the ready position » page 125.
› Remover the cover A from the handwheel lock in the direction of the arrow 1 » Fig. 149. › Insert the key into the handwheel lock. › Turn the key B 2 in the direction of the arrow as far as the stop. Removing ball rod - Step 2 The ball rod must be cleaned before storing in the box with the vehicle tool always. WARNING Never allow the tow bar to remain unsecured in the boot.
Note We recommend that you use accessories from ŠKODA Original Accessories. Using the towing device Trailer (accessory) connect and disconnect Fig. 152 Swivel out the 13-pin power socket, safety eyelet Power supply of the trailer / accessory power system In the electrical connection between the vehicle and trailer (accessory), the trailer (accessories) is supplied with power from the vehicle (with ignition switched on and off).
Trailer The permissible trailer load must not be exceeded under any circumstances. Permissible trailer load Engine 1.2 ltr./81 kW TSI 1.4 ltr./92 kW TSI 1.4 ltr./110 kW TSI 1.6 l./81 kW MPI 1.8 ltr./112 kW TSI 2.0 ltr./81 kW TDI CR 2.0 ltr./103 kW TDI CR 2.0 ltr.
Brakes Apply the brakes in good time! If the trailer is fitted with a trailer brake, apply the brakes gently at first, then brake firmly. This will avoid brake jolts resulting from the trailer wheels locking. On downhill sections shift down a gear in good time to also use the engine as a brake. WARNING Always drive particularly carefully with the trailer. CAUTION With frequent towing, the vehicle is excessively loaded so this must also be checked between service intervals.
Vehicle operating under different weather conditions General Maintenance Care and maintenance Introduction This chapter contains information on the following subjects: Vehicle operating under different weather conditions Statutory checks ŠKODA service partner ŠKODA Original parts ŠKODA Original accessories Spoiler Component protection Airbags Acceptance and recycling of used vehicles on page 131 first.
ŠKODA Original parts Read and observe Spoiler on page 131 first. We recommend the use of ŠKODA Genuine Parts for your vehicle, as these parts are approved by ŠKODA AUTO. These parts comply wholly with ŠKODA AUTO regulations and are identical to the parts used in series production. ŠKODA AUTO is able to warrant the safety, suitability, and long life of these products.
WARNING No changes may be made to airbag system components, the front bumper and the bodywork. ■ Any work on the airbag system including the installation and removal of system components due to other repair work (e.g. removal of the steering wheel) must only be carried out by a specialist garage. ■ Do not manipulate individual parts of the airbag system, as this might result in the airbag being deployed. ■ If the airbag has been deployed, the airbag system must be replaced.
Inspectionb) Variant 1 Overview of service intervals Inspectionb) Variant 2 Inspectionb) Variant 3 Brake fluid change Fig. 153 Vehicle data: Service Interval a) b) In order to operate a vehicle with a variable service interval, it must only be filled and topped up with the prescribed engine oil. If this engine oil is not available, the oil change is subject to a fixed service interval. In this case, the vehicle must be changed to the fixed service interval.
WARNING The brake fluid must always be changed after the first 3 years and then every 2 years. Longer intervals between changing the brake fluid can cause vapour bubbles to form in the brake system when braking sharply. This can impair the efficiency of the brakes – risk of accident! Digital Service Plan We therefore recommend that you always have the record of work carried out in a service printed out for you.
If your vehicle is fitted with any particular attached parts (e.g. spoiler, roof rack system, aerial etc.) it is best to consult the operator of the car wash system beforehand. Exterior car care After an automatic wash with wax treatment, the wiper blades should be cleaned with cleaning agents specially designed for the purpose, and then degreased. Pressure Washers When washing the vehicle with a high-pressure cleaner, the instructions for use of the equipment must be observed.
The towing device is maintenance-free. Coat the ball head of the towing device with a suitable grease whenever necessary. Protection of cavities All the cavities of your vehicle which are at risk from corrosion are protected by a layer of long-lasting protective wax applied in the factory. If any small amount of wax flow out of the cavities at high temperatures, these must be removed with a plastic scraper and the stains cleaned using a petroleum cleaner.
Caring for the interior Read and observe Vehicle components and on page 135 first.
Petrol and diesel refuelling Inspecting and replenishing Fuel Introduction Fig. 154 Stickers showing the prescribed fuel Fig. 155 Open fuel filler flap / unscrew tank cap / place the tank cap on the fuel filler flap This chapter contains information on the following subjects: Petrol and diesel refuelling Unleaded petrol Diesel fuel 139 140 140 The correct fuel for your vehicle is specified on the inside of the fuel filler flap» Fig. 154.
Read and observe Lower than 91 octane petrol should not be used, even in an emergency! If a fuel other than unleaded fuel which complies to the above mentioned standards (e.g. leaded petrol) is put in the tank by mistake, do not start the engine or switch on the ignition. ■ ■ Unleaded petrol and on page 139 first. The correct fuel for your vehicle is specified on the inside of the fuel filler flap» Fig. 154 on page 139.
Operating under different weather conditions Use only diesel in accordance with the current or expected weather conditions. Ask the petrol station personnel whether the diesel fuel offered corresponds to these conditions. CAUTION The following instructions must be observed, otherwise there is a risk of damage to the engine and to the exhaust system. ■ If a different fuel other than diesel fuel, which complies to the above mentioned standards (e.g.
Refilling AdBlue® refill › Fold up the flooring in the luggage compartment in the arrow direction Fig. 156 Raise flooring / remove box / cover lid 1 » Fig. 156. › Remove the box for the vehicle tools in the direction of arrow 2 . › Open the filler cap in the direction of the arrow 3 » Fig. 157. › Unscrew the tank cap in the direction of arrow 4 . › Fill the AdBlue® through the filler A according to the instructions on the refill bottle.
WARNING (Continued) Firmly apply the handbrake. For vehicles with manual transmission the lever into the neutral position. For vehicles with automatic transmission, place the selector lever in the P position. ■ Allow the engine to cool. ■ Never open the bonnet if you can see steam or coolant flowing out of the engine compartment – There is a risk of scalding! Wait until the steam or coolant has stopped escaping.
Engine compartment overview Read and observe and on page 142 first. The windscreen washer fluid reservoir A is located in the engine compartment » Fig. 160. The capacity of the reservoir A is about 3 litres or about 5.5 litres on vehicles that have a headlight cleaning system1). Use a suitable windscreen washer fluid for the current or expected weather conditions. We recommend that you use windscreen washer fluid from ŠKODA Original Accessories.
WARNING The following instructions must be followed at all times when working on the engine compartment » page 142. CAUTION Do not add any additives to the engine oil - There is a risk of engine damage. Note We recommend that you use oils from ŠKODA Original Accessories. CAUTION If no prescribed engine oil is available, then max. 0.5 l oil of the following specifications can be refilled. ■ Petrol engines: ACEA A3/ACEA B4 or API SN, (API SM); ■ Diesel engines: ACEA C3 or API CJ-4.
CAUTION The oil level must never be below range A » Fig. 161 – risk of damage to the engine as well as to the exhaust system. ■ If a top up with oil is not possible or the oil level is above range A , Stop driving! Switch off the engine and seek assistance from a specialist garage. ■ CAUTION Do not cover the radiator and install any parts (e.g auxiliary lights.) in front of the air intakes - There is a risk of the engine overheating.
CAUTION If the expansion tank is empty, do not top up with coolant. The system could aerate - There is a risk of engine damage! Stop driving! Switch off the engine and seek assistance from a specialist garage. ■ Do not fill the coolant above the mark A » Fig. 162. The coolant could, when heated, be expelled from the cooling system - There is a risk of damage to the engine parts. ■ If it is not possible to add coolant, stop driving! Switch off the engine and seek assistance from a specialist garage.
Warning symbols on the vehicle battery Symbol Meaning Always wear eye protection. Battery acid is severely caustic. Always wear gloves and eye protection. Keep fire, sparks, open flames and lit cigarettes well clear of the vehicle battery. When charging the vehicle battery, a highly explosive gas mixture is produced. CAUTION Ensure that battery acid does not come into contact with the bodywork – There is a risk of damage to the paintwork.
Battery discharge If frequent short journeys are made, the vehicle battery does not recharge sufficiently. The battery capacity decreases at low temperatures. If the vehicle is not used for longer than 3 to 4 weeks, disconnect the negative terminal of the battery or charge the battery completely with a very low charging current. Read and observe Read and observe and on page 148 first. The new vehicle battery must have the same capacity, voltage, current and the same size as the original Battery.
Fitting new tyres Only fit approved radial tyres of the same type, size (rolling circumference) and the same tread pattern on one axle on all four wheels. Wheels Wheels and tyres When mounting new tires the tires have to be replaced axle by axle.
Tyre pressure WARNING Do not drive with incorrect tyre pressure - There is a risk of accident. In the event of very rapid pressure loss (e.g. in the event of tyre damage) an attempt should be made to bring the vehicle carefully to a stop without sudden steering movements and without any hard braking - risk of accident. ■ ■ Note The declaration of conformity (COC document), can be obtained from a ŠKODA1) partner. Fig.
To ensure uniform wear on all tyres, we recommend that you change the wheels every 10 000 km, in line with the schedule» Fig. 166 - . WARNING ■ Change the tyres at the latest when they are worn down to the wear indicators -There is a risk of an accident. ■ Faulty wheel alignment affects handling - There is a risk of an accident. ■ Unusual vibrations or the vehicle “pulling ” to one side could be a sign of tyre damage.
The speed limit for all-season or “winter”Tires can be adjusted in MAXI DOTDisplay in the menu item winter tires » page 43. If the vehicle has all-season or “winter”tires of a lower speed category then the specified maximum speed of the vehicle (referring to tyres that have not been delivered by the factory, a warning label with the maximum value of the speed category provided for the mounted tyres must be fixed in the interior of the vehicle in a constantly visible place in the driver’s field of vision.
WARNING Properly secure the first aid kit and the warning triangle - there is a risk of injury in the event of sudden braking or a vehicle collision. Do-it-yourself Emergency equipment and self-help Emergency equipment Location of reflective vest Introduction Fig.
WARNING Always properly secure the fire extinguisher - there is a risk of injury in the event of sudden braking or a vehicle collision. Vehicle tool kit WARNING The factory-supplied lifting jack is only intended for your model of vehicle. Under no circumstances attempt to lift other vehicles or loads with it – there is a risk of injury.
› Jack up the vehicle» page 158 until the wheel that needs changing is clear of the ground. › Unscrew the wheel bolts and place them on a clean surface (cloth, paper, etc.). › Remove the wheel carefully. › Attach the spare wheel and slightly screw on the wheel bolts. › Lower the vehicle. › Tighten the wheel bolts opposite each other using the wheel wrench (“pulling crossways”)» page 158. › Replace the wheel trim » page 156 and caps » page 157.
Install trim › Press the wheel trim onto the wheel rim at the designated valve opening. › Then press the trim into the wheel rim until its entire circumference locks correctly in place. Anti-theft wheel bolts Fig. 173 Anti-theft wheel bolt and attachment The position of the anti-theft wheel bolt is indicated by means of a symbol on the back of the wheel trim supplied ex-factory or from the ŠKODA Original Accessories. If using the anti-theft wheel bolt it should be fitted at this point » .
Loosening/tightening wheel bolts Fig. 174 Loosening the wheel bolts Fig. 176 Attach lifting jack › Insert the wheel wrench onto the wheel bolt to the stop. Use the associated attachment for the anti-theft wheel bolts » Fig. 173 on page 157. › To loosen the screws, grasp the key end and turn the screw about one turn rotation in the direction of the arrow » Fig. 174. › Totighten the screws, grasp the key end and turn the screw about against the direction of the arrow » Fig. 174, until it is tight.
CAUTION It is important to ensure that the jack is correctly positioned against the bar of the lower beam - otherwise there is a risk of damage to the vehicle.
Preparing to use the breakdown kit Read and observe on page 159 first. For safety's sake, the following instructions must be observed before undertaking a wheel repair on a road. › Park the vehicle as far as possible away from the traffic flow - choose a place with a flat and firm surface. › Switch off the engine. › For vehicles with manual transmission, select 1. gear. › For vehicles with automatic transmission, place the selector lever in the P position. › Firmly apply the handbrake.
If the tyre inflation pressure is 1.3 bar or more › Set the tyre pressure back to the correct value » page 151. › Continue driving carefully to the nearest specialist garage at a maximum speed of 80 km/h (50 mph). Jump-starting using the battery from another vehicle WARNING A tyre filled with sealant has the same driving characteristics as a standard tyre. The following guidelines must be observed. ■ Do not drive faster than 80 km/h (50 mph).
WARNING Never clamp the jump cable to the negative terminal of the discharged battery -There is a risk of an explosion.
Front towing eye Towing eye rear Fig. 180 Remove cap / install towing eye Fig. 181 Remove cap / install towing eye Cap removal/fitting › To remove, press down on the cap in the direction of arrow 1 and remove it in the direction of arrow 2 » Fig. 180. › To fit it, insert the cap in arrow range 1 and then press on the opposite edge of the cap. The cap must engage firmly. Cap removal/fitting › To remove, press down on the cap in the direction of arrow 1 and remove it in the direction of arrow 2 » Fig.
› Remove the discharged battery in the direction of arrow 2 and install a new battery. › Insert the battery cover A and press it down until it clicks audibly into place. Remote control and removable light - replacing the battery/batteries Introduction Remote control of the auxiliary heating This chapter contains information on the following subjects: Key with fold-out key bit Remote control of the auxiliary heating Removable light Fig.
› Lever off the cover for the rechargeable batteries with a narrow and pointed object from the area of the lock clips A . › Replace the batteries. › Insert the cover for the rechargeable batteries and press it down until it clicks into place. CAUTION Make sure you do not damage the paint when performing an emergency locking/unlocking.
Replacing the windscreen wiper blades Selector lever-emergency unlocking Fig. 189 Setting the service position for the wiper arms Fig. 188 Remove / release the selector lever › Firmly apply the handbrake. › Insert a slot screwdriver or similar tool into the gap in the arrow area 1 » Fig. 188 and lift the cover in arrow direction 2 . › Press on the yellow plastic part in the direction of arrow 3 , simultaneously press the lock button in the selector lever handle and put the lever in position N.
Attaching the windscreen wiper blade › Slide the windscreen wiper blade in the opposite direction to arrow 3 until it locks into place. Check that the windscreen wiper blade is correctly attached. › Fold the windscreen wiper arm back to the windscreen. › Turn on the ignition and press the lever in the direction of the arrow » Fig. 189. Fuses and light bulbs Fuses The windscreen wiper arms move into the home position. Introduction Fig.
Fuses in the dashboard Fig. 193 Distribution board cover. Read and observe No. 1 2 3 4 5 Read and observe and on page 167 first. The fuses are located on the left side of the dash panel behind a cover. Replacing fuses › Remove the ignition key, turn off the lights and all electrical consumers. › Insert a screwdriver into the opening in the cover in the direction of the arrow » Fig. 193. › Remove the cover of the fuse box and remove.
No.
No. off the ignition and all of the lights before replacing a bulb. bulbs must only be replaced with the same type of bulbs. The designation is located on the light socket or the glass bulb.
Bulb arrangement in the front headlights Fig. 197 Left headlight › Remove the connector to the bulb in the direction of arrow 2 . › Remove the connector. › Insert the connector with the new bulb so that the fixing lug A fits on the bulb» Fig. 198 into the recess on the reflector. › Insert the respective protective cap » Fig. 197 on page 171 and rotate it clockwise until it stops. Note We recommend you have the bulb replacement performed by a specialist garage.
Protective grille for removing fog lights- plug for Park Assist sensor Changing light bulbs for fog lights Fig. 202 Remove the number plate light / replace the bulb Fig. 200 Guard: Version 1/version 2 Read and observe and on page 170 first. First remove the grille for the fog lights and before changing bulbs » Fig. 199 on page 171 and / or » Fig. 200 on page 172. Removing the headlight › Unscrew the screws A » Fig. 202 with the screwdriver from the tool kit.
CAUTION For vehicles with parking assistance, we recommend that after changing the light bulb in the fog lights, the system is checked by a specialist. Removing/installing taillights Changing the bulb for the licence plate light Fig. 204 Remove light / pull out connector Fig. 203 Remove / replace the bulb for the number plate light Read and observe and on page 170 first. › Open the boot lid. › Push the light in the direction of arrow 1 » Fig. 203 until it comes loose.
Replacing the bulbs in the taillight assembly Light with LED diodes › Unlock the bulb holder using the locking latches in the areas » Fig. 206 marked with arrows and remove the bulb holder from the light. › Turn the respective light bulb » Fig. 206 until it stops counter-clockwise and remove it from the bulb holder. › Insert a new bulb into the holder and turn in a clockwise direction to the stop. › Insert the lamp holder in the lamp until it is secure. Fig.
Vehicle data Technical data Technical data Basic vehicle data Introduction This chapter contains information on the following subjects: Vehicle data Operating weight Payload Measurement of fuel consumption and CO2 emissions according to ECE Regulations and EU Directives Dimensions Angle and gradeability 175 176 176 177 178 179 The details given in the vehicle's technical documentation always take precedence over the details in the Owner's Manual.
10 11 Maximum permissible front axle load Maximum permissible rear axle load Vehicle identification number (VIN) The vehicle identification number - VIN (vehicle body number) is stamped into the engine compartment on the right hand suspension strut dome. This number is also located on a sign on the lower left hand edge below the windscreen (together with a VIN bar code), and on the type plate. Engine number The engine number (three-digit identifier and serial number) is stamped on the engine block.
Measurement of fuel consumption and CO2 emissions according to ECE Regulations and EU Directives The data on fuel consumption and CO2 emissions were not available at the time of going to press. The data on fuel consumption and CO2 emissions are given on the ŠKODA websites or in the sales and technical vehicle documentation. The measurement of the intra-urban cycle begins with a cold start of the engine. Afterwards urban driving is simulated.
Dimensions Fig. 208 Vehicle dimensions Vehicle dimensions for operating weight without driver (in mm) » Fig.
Angle and gradeability C D Overhang angle, rear Pitch angle / climbing ability The departure angle values indicate the maximum incline of a slope, up which the vehicle can drive at a slow speed without the bumper or underbody making contact with the slope. The values listed correspond to the maximum axle load, front or back. The ramp angle indicates the value to which the vehicle can travel at a slow speed on a ramp without setting the underbody on the ramp edge.
Engine 2.0 ltr./110 kW TDI CR a) Transmission Front overhang angle (°) Rear overhang angle (°) Ramp angle (°) Slope angle (°) / climbing ability (%) MG MG 4x4 19 19 32 32 19.6 19.6 41/86 39/80 DSG 4x4 19 32 19.6 38/77 Applies to vehicles with tyre size 205/55 R 16.
Vehicle-specific data depending on the engine Introduction This chapter contains information on the following subjects: 1.2 ltr. / 81 kW TSI engine 1.4 l/92 kW TSI engine 1.4 l/110 kW TSI engine 1.6 l/81 kW MPI engine 1.8 ltr./112 kW TSI engine 2.0 ltr./81 kW TDI CR engine 2.0 ltr./103 kW TDI CR engine 2.0 ltr.
1.4 l/110 kW TSI engine Output (kW/rpm) Maximum torque (Nm at 1/min) Number of cylinders/displacement (cm3) Transmission Top speed (km/h) Acceleration 0-100 km/h (s) 110 / 5000-6000 250 / 1500-3500 4/1395 MG 4x4 195 8.7 DSG 4x4 191 8.9 1.6 l/81 kW MPI engine Output (kW/rpm) Maximum torque (Nm at 1/min) Number of cylinders/displacement (cm3) Transmission Top speed (km/h) Acceleration 0-100 km/h (s) 81/5800 155/3800 4/1598 MG 175 11.8 AG 172 13.3 1.8 ltr.
2.0 ltr./81 kW TDI CR engine Output (kW/rpm) Maximum torque (Nm at 1/min) Number of cylinders/displacement (cm3) Transmission Top speed (km/h) Acceleration 0-100 km/h (s) MG (EU4, EU5) MG (EU6), MG 4x4 MG (EU4, EU5) MG (EU6), MG 4x4 MG (EU4, EU5) 177 11.6 81/4200 81/3500 250 / 1500-2500 250 / 1750-3000 4/1968 MG (EU6) 179 11.7 MG 4x4 175 12.2 2.0 ltr.
Index A ABS Operation Warning light Acceptance and recycling of used vehicles Accessories Adaptive headlight see xenon headlight AdBlue Check level indicator light refill Adjusting Steering wheel Adjusting seats manually Adjusting the seats Advice on tyre/wheel usage AFS Display messages Warning light AHL see xenon headlight Air-conditioning system Air outlet vents Airbag Adjustments and impairments to the airbag system Deactivation Deployment Warning light Airbag system Air conditioning Air distribution co
C Camera See reversing camera Car battery Check condition Cover Disconnecting and reconnecting Replacing Winter operation Car care Exterior Interior Car computer See multifunction display Care and maintenance Carrier Car washing Exterior Interior Washing Central locking Problems Central locking button Changing Batteries for the removable light Battery Windscreen wiper blades Changing a wheel Changing Changing gear Selector lever Changing wheels Wheels Charging a vehicle battery Check Brake fluid Engine oil
Door Child safety lock Emergency locking Emergency locking of the driver's door Opening/Closing warning light door open Door alarm Door open warning light Drive Driving through water Driver Steering Recommendation (DSR) Driving Emissions Fuel consumption through water Top speed DSR 51 165 165 50 32 38 32 109 111 177 177 109 181 111 E 108 Economical driving EDL 111 Electrical power windows 55 Button in the rear doors 54 Electric power windows 53 Electric window Buttons in the driver´s door 54 Electric wind
G Gear change Gear recommendation Information on the selected gear Gear changing Gear stick Genuine parts Glasses compartment GPS See Owner's Manual Infotainment gradeability 39 39 105 132 81 6 179 H Handbrake Warning light Hazard warning light system HBA Headrests Heating Air distribution control Controls Mirrors Seats Windscreen and rear window Help in an emergency HHC Hill Start Assist (HHC) Hitch Horn 104 32 61 111 73 93 96 94 67 74 63 8 111 111 124 27 I Ignition lock Images See Owner's Manual Infot
Lock Individual settings Key Locking Central locking button in case of emergency KESSY Remote control Lock steering lock Low tyre pressure warning refer to the tyre pressure monitoring Luggage compartment Cover Fastening elements Fastening with sliding hook Fixing nets Flexible storage compartment Floor covering on both sides Net partition Side compartments unlock manually Unlock the boot lid Variable loading floor Luggage compartment cover Luggage compartment lid Luggage Storage lighting removable lamp 50
Parking Park Assist Parking aid Reversing camera Parking aid Function Parking assistance Activation / deactivation Display in the Infotainment display Parking lights Parking the vehicle See Parking ParkPilot Parts replacement Passive safety Before setting off Driving safety Passive Safety Pedals Footmats Petrol Phone See Owner's Manual Infotainment Pocket in the luggage compartment Pockets Power limit Tilt / slide sunroof Power steering Power windows Button in the front passenger door Practical equipment st
Seatbelts Inertia reels 15 Seat belts Warning light 32 Seat electrical adjustment 69 Seats Electrical adjustment 69 Folding front passenger seat 70 front 68 Front armrest 71 Headrests 73 Heating 74 Manually adjusting 68 Memory Function of the electrically adjustable 69 seat Rear 71 Setting 68 Storing in memory of remote control key 70 Seats and head restraint 68 Selector lever 106 Selector lever control 106 Selector lever lock Warning light 37 Service 131 Service interval display 44 Service intervals 133, 1
T Table on the front seat backrest on the middle rear seat backrest Tablet holder TCS Deactivate/activate Function Warning light Technical data Through-loading bag Ticket holder Tilt / slide sunroof Activate operation Operation Time Tiptronic Tools Top speed TOP TETHER Towing Towing a trailer Towing away Towing device Accessories Description Vertical load Towing eye Towing protection Towing the vehicle Traction control (TCS) Trailer Connect and disconnect Load loading Towing a trailer Trailer stabilization
Vehicle length Vehicle tool kit Vehicle width Vest VIN Vehicle Identification Number Visibility Visors Voice Operation See Owner's Manual Infotainment 178 155 178 154 175 63 64 6 W Warning lights MAXI DOT display Warning of a low temperature Warning symbols MAXI DOT display see Warning lights Warning triangle warning when speeding Warranty Waste container Water in the fuel filter Weather conditions Weights Wheel bolts Anti-theft wheel bolts Caps Loosening and tightening Wheels Full trim Load Index Snow ch
Index 193
194 Index
Reprinting, duplicating, translating and any other use, either in whole or in part, is not permitted without the written consent of ŠKODA AUTO a.s.. ŠKODA AUTO a.s. expressly reserves all rights relating to copyright laws. Subject to change. Issued by: ŠKODA AUTO a.s. © ŠKODA AUTO a.s.
www.skoda-auto.com Návod k obsluze Yeti anglicky 11.2016 S90.5610.29.
