Datasheet

Technical parameters
Assembly instruction
1. Switch off the mains to which the lamp is going to be connected. Double check with a measuring device if the power is off.
2. Drill 4 mounting holes in the ceiling (diameter: 6 mm; depth: 30 mm). Refer to the drawing for the correct spacing when drilling in concrete.
The set includes also special wall plugs for plasterboard. Openings for this type of mounting should have 8 mm diameter.
3. Unscrew fastening bolts (1) and remove the lower casing (2).
4. Place the wall plugs (4) in the mounting holes.
5. Drag the wires L, N, PE through the opening (6) in the body.
6. Fix the body (3) to the ceiling with screws (5).
7. Connect the wires to the terminal plate (8) according to the description (7). Place the plastic cover (11) on the terminal plate (8).
8. Tread the steel cord (9) through the opening in the lamp yoke (12). Use two cords for each yoke.
9. Loosen the fastening clamp in the body (10) and thread the cord (9) through the opening in the clamp. Adjust the cord (9) length and tighten
the fastening clamp (10). Repeat this action for all four cords so that their length is the same. After adjustment, cut off the cord ends so that
they do not interfere with the electrical wiring system.
10. Place the lower casing (2) on the body (3) and fix it with fastening bolts (1). Hold the lamp up – loose cords will enable easier casing
assembly.
11. Turn the power on.
Electrical wiring diagram
Electrical installation Lamp
CAUTION!
All assembly works should be carried out by a qualified person. The installation should be performed according to the diagram. A correctly
installed lamp is ready to use after connecting to the mains. For 1st class protection against the electric shock ensure that the ground wire
is neither damaged nor broken. DC power supply applied in the LED lamp is protected against short-circuit and overload.
The maximium power consumption is 25 W. For such low energy consumption the lamps emit 1200 luminous flux [Lm]. For comparison: the
luminous flux of a standard 100 W bulb is 1360. Moderno lamp efficiency is almost 4 times higher compared to a standard incandescent lamp.
Lamp dimensions
MODERNO ELEGANTE Ceiling lamp 50 W MODERNO ELISSE Ceiling lamp 50 W
Colour of light
Rated voltage
1800 lm
10 x 5 W LED 4500 – 5500 K
10 x 5 W LED 3000 – 3500 K
Rated power
Material
50 W
Protection class
L, N, PE
I
Type of switch
Ingress protection
universal double wall switch
IP20 – interiors only
Weight 5,4 kg
Conformity with EMI standards
(emission)
PN-EN 55015:2007, PN-EN 55015:2007/A1:2007
PN-EN 55015:2007/A2:2009
Conformity with LVD standards PN-EN 60598-1:2007, PN-EN 60598-2-6:2000
PN-EN 61547:2002
Protection
against short-circuit and overload
Cold white
Index
Cold white
MODERNO ELEGANTE Ceiling lamp MODERNO ELISSE Ceiling lamp
Warm white
Warm white
Technical parameters
230 V AC 50Hz –15%, +10%
Light stream
Connection wires
Conformity with EMI standards
(resistance)
aluminum and glass
MO–LWI–C–W
MO–LWI–C–H
ME–LWI–C–W
ME–LWI–C–H
Najlepsza inwestycja w światło
The best investment in light
www.skoff.pl MADE IN POLAND
43-500 Czechowice-Dziedzice
ul. Legionów 243 D, POLAND
tel./fax [phone]
email: info@skoff.pl
www.skoff.pl MADE IN POLAND
43-500 Czechowice-Dziedzice
ul. Legionów 243 D, POLAND
tel./fax [phone]
email: info@skoff.pl