Contents 1 Safety Precautions ......................... 2 2 Overview......................................... 4 3 Installing the SIM card ................. 5 4 Installing the storage card ............ 7 5 Charging ......................................... 7 6 Power on / Power off ..................... 8 7 Android Home Screen Guides ...... 9 8 Changing OSD Language & System Time .................................... 10 9 Connecting to Wi-Fi® ..................
Notice The phone pictures, as well as data on the phone appearance, color and design features found in the manual are for reference only. We reserve the right to change the appearance and technical parameters of the product without prior notice. 1 Safety Precautions Never attempt to disassemble your phone. You alone are responsible for how you use your phone and any consequences of its use. As a general rule, always switch off your phone wherever the use of a phone is prohibited.
hearing damage, do not listen at high volume levels for long periods. Explosive materials: Please comply with warning signs at gas stations asking you to switch your phone off. You will need to comply with radio equipment usage restrictions in places such as chemical plants, fuel depots and at any location where blasting operations are under way. Electronic equipment: To avoid the risk of demagnetization, do not let electronic devices close to your phone for a long time.
phone a minimum of 10mm from your body. The use of other accessories may not ensure compliance with radiofrequency exposure guidelines. If you do not use a body worn accessory and are not holding the phone at the ear, position the phone a minimum of 10mm from your body. • Data operation: When using a data feature, position the phone a minimum of 10 mm from your body for the whole duration of the data transmission.
Touch Screen Light Sensor Earpiece Charging Indicator Light Frontal Camera Back Panel Back Camera Flash Light Speaker Microphone 3 Installing the SIM card You need to remove the back cover before you can install the SIM card and battery.
always turn off the power before installing or replacing the SIM card and battery. To prize up the back cover 1) Make sure your device is turned off. 2) Use your nail or pick to open up the back cover, since there is a slot at the right bottom corner of back cover. To install the SIM card Your device is supported both 2G and 3G (WCDMA) SIM cards. 1) Remove the battery if it is installed. 2) Locate the SIM card slot, and then insert the SIM card with it's direction as the following figure.
4 Installing the storage card To have additional storage for your images, videos, music, and files, you can purchase a memory card and install it into your device. 1) Make sure that your device is turned off, and then remove the back cover. 2) Remove the battery if it is installed. 3) Locate the memory card slot on the upper part of the exposed Right panel. 4) Insert the memory card into the slot according to the indication icon. To remove the memory card, perform converse installations.
you start using your device, it is recommended that you install and charge the battery. Some batteries perform best after several full charge/discharge cycles. Plug the DC end of adapter to the micro USB port of the device and plug the AC end to the wall socket for charging. Normally it takes approximately 3~5 hours to fully charge the device. Operating the device during charging with the AC adapter may extend the time of full charging.
Notice If the system halts, press and hold the Power button until it is turned off completely.
8 Changing OSD Language & System Time On the Home menu tap on the icon and select Settings icon to access the list of options. Select Settings---Language & input---Language to change OSD language. Select Settings---Date & time to change system time. 9 Connecting to Wi-Fi® On the Home menu tap on the icon and select Settings icon to access the list of options. Select Wireless & Networks. If the Wi-Fi® is off, tap on the Wi-Fi® line to turn it on.
Your device will now attempt to establish a connection to the Wi-Fi® access point with the network parameters you entered. 10 Transferring Contents from PC Connect the device to your PC/Notebook via USB cable. If the network of your PC/Notebook is on, it will install the required driver automatically then tap "Turn on USB storage" on the screen to turn on USB storage function. Select the contents you want to transfer from your PC/Notebook. Drag the contents from the PC/Notebook to the device.
11 Troubleshooting Q1: What if water enters the device? A: 1) DO NOT turn on the device. 2) Disconnect the outlet cable in order to turn it off instead of pressing the power button. Disconnect all external devices and then send to the service center for advice. Q2: How to check the device if it won’t turn on? A: If the power is low, connect the adapter to charge. Remove the micro-SD card and any other external device.
Set the sleep time to proper level on Settings--- Display---Sleep menu. Q5: What to do if the micro SD or SIM card can’t be read? A: Please turn off the device and re-insert the card. Q6: Why are the Bluetooth and 3G function disabled? (Applicable only for model with Bluetooth and 3G function) A:Check if the “Airplane mode” is enabled, if it is then the Bluetooth and 3G function can’t be activated.
12 Technical Specifications Processor MT6580 RAM (#) 2GB Storage capacity(#) EMMC 16GB Size Resolution Descriptions Communications Operating Temperature 5.0” HD Capacitive Multi-touch 720x1280 pixels Front: 8.0M pixel; Back: 13.0M pixel Wi-Fi® (802.11 b/g/n), Bluetooth®(BT4.
13. FCC WARNING Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver.
technician for help. 14 Specific Absorption Rate (SAR) information SAR tests are conducted using standard operating positions accepted by the FCC with the phone transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value, in general, the closer you are to a wireless base station antenna, the lower the power output.
For body worn operation, this model phone has been tested and meets the FCC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that contains no metal and that positions the handset a minimum of 10 mm from the body. Non-compliance with the above restrictions may result in violation of RF exposure guidelines. ISEDC WARNING This device complies with Innovation, Science, and Economic Development Canada licence-exempt RSS standard(s).
(1) l'appareil nedoit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Radio apparatus containing digital circuitry which can function separately from the operation of atransmitter or an associated transmitter, shall comply with ICES-003. In such cases, the labelling requirements of the applicable RSS apply, rather than the labelling requirements in ICES-003.
et la conformité and compliance d’acquérir les informations correspondantes La distance minimale du corps à utiliser le dispositif est de 10mm.