UG0214

4. To turn the meat slicer ON, push the Green "I" buon. (Fig. 2)
5. To turn the meat slicer OFF, push the Red "O" buon.
6. When operang slicer, stand to the side of the slicer opposite the blade.
7. Place a tray or plate behind the Meat Slicer and below the Blade #8 to collect the sliced
food as it exits the blade area.
8. Hold the Food Pusher Handle #11 with right hand. Keep your hands protected behind
the Food Pusher #5.
9. NEVER USE THIS SLICER WITHOUT THE FOOD PUSHER #12
Important: Refer to "Food Slicing Tips" secon, when slicing different types of food items.
10. Using an even, steady moon, SLOWLY begin slicing. Apply light steady pressure with
the Food Pusher #12 to move food toward the Adjustment Plate #3 while SLOWLY sliding
Food Carriage #5 over Blade #8; This will help assure even slicing. Connue sliding SLOWLY,
back and forth, unl you have sliced the desired amount of meat.
NOTE: Meat slicer only makes slices during the forward moon.
11. When finished, turn the meat slicer "OFF" (0) by pushing the Red buon. (Fig. 2)
12. Always unplug meat slicer from power source when the Meat Slicer is not in use.
13. For safety, always rotate the Thickness Adjustment Knob #2 all the way to the "O"
posion aer use to properly shield the sharp edge of Blade #8.
5.1 Food Slicing Tips
FIGURE 02
WARNING
This Meat Slicer is not meant to cut through any bones! Severe damage to Meat
Slicer will occur and Warranty will be voided!
• Always debone meat before slicing
• Fruits should be free of seeds (peaches, apples, avocadoes etc.) The excepon is
tomatoes.
• DO NOT slice fully frozen foods.
• If you have to large of a cut of meat (roast or slab bacon) you may need to cut into a more
manageable slicing pieces.
• Food with an uneven texture, like fish and thin steaks, are oen difficult to slice. Put in
freezer for approx. 20 minutes to parally freeze.
IMPORTANT
Carefully read ALL INSTRUCTIONS of this manual before turning the machine ON.
Be sure to well understand all the informaon contained in this manual. If you
have any queson contact your supervisor or your nearest Dealer.
7.2.1 Danger
An electric cable or electric wire with damaged jacket or bad insulaon might cause
electrical shocks as well as electrical leak. Before use, check the condions of all wires
and cables.
7.2.2 Advices
Be sure to well understand all the informaon contained in this manual. Every operaon
funcon or procedure has to be thoroughly clear.
Before using any commands (switch, buons, lever), be sure it is the correct one. In case
of doubt, consult this manual.
7.2.3 Precauons
The electric cable has to be compable with the power required by the machine.
Cables touching the floor or close to the machine need to be protected against short
circuits.
7.3 Roune Inspecon
7.3.1 Advice
When checking the tension of the belts or chains, DO NOT insert your fingers between the
belts and the pulleys and nor between the chain and the gears.
7.3.2 Precauons
Check the motor and sliding or turning parts of the machine in case of abnormal noises.
Check the tension of the belts and chains and replace the set when belts or chains show
signs of wearing.
When checking the tension of belts or chains DO NOT insert your fingers between belts
and pulleys, nor between the chains and gears.
Check protecons and safety devices to make sure they are working properly.
7.4 Operaon
7.4.1 Warnings
Do not use the machine with long hair that could touch any part of the machine. This might
lead to a serious accident. Tie your hair up well and/or cover it with a scarf.
Only trained or skilled personnel shall operate this machine.