Instructions / Assembly

ManualsBrandsSkyLink ManualsDoors & Windows3/4 HPF Belt Drive Garage Door Opener with Extremely Quiet DC Motor and WiFi Connectivity

IMPORTANT:

•

• Safety Infrared Sensor MUST BE INSTALLED and aligned properly.

• Periodic checks of the opener are required to ensure safe operation.

• Save this manual for future reference.

• This Equipment meets or exceeds all Federal, State and UL325 Safety Requirements.

DO NOT RETURN TO THE STORE

ENGLISH

P/N: 101Y428

ENGLISH

DC Motor Belt Drive

ATOMS /ATOMS+ ATR/ANR Series

GARAGE DOOR OPENER

INTRODUCTION............................................................................................................................... 3

PRE-INSTALLATION CHECKLIST ...................................................................................................

WHAT IS INCLUDED ........................................................................................................................ 5

IMPORTANT INSTRUCTIONS.......................................................................................................... 8

ASSEMBLE THE RAIL ...................................................................................................................... 9

INSTALL THE HEADER BRACKET .................................................................................................14

HANG THE OPENER....................................................................................................................... 17

INSTALL THE DOOR BRACKET.....................................................................................................

INSTALL THE DOOR ARMS ........................................................................................................... 21

INSTALL THE WALL CONSOLE/LCD WALL CONSOLE

CONNECT THE OPENER TO POWER..........................................................................................

INSTALL SAFETY BEAM SENSOR................................................................................................ 27

PROGRAMMING GUIDE 38

SAFETY TEST.................................................................................................................................

OPERATIONS

...............................................................................................................................

MAINTENANCE

.............................................................................................................................. 49

BACKUP BATTERY........................................................................................................................

TROUBLE SHOOTING....................................................................................................................

PROGRAMMING TO THE INTERNET HUB.................................................................................... 57

ACCESSORIES............................................................................................................................... 59

FCC................................................................................................................................................. 61

LIMITED WARRANTY .................................................................................................................... 62

INSTRUCTION MANUAL

TABLE OF CONTENT

CUSTOMER SERVICE.................................................................................................................... 63

Please read this manual and enclosed safety materials carefully!

• For more information, updates and useful links, please visit our website http://www.skylinkhome.com

P/N: 101Y549-001

SET

.............................................................................................................

.............................................................

Summary of content (32 pages)

PAGE 1
INSTRUCTION INSTRUCTIONMANUAL MANUAL TABLEOF OFCONTENT CONTENT TABLE INTRODUCTION............................................................................................................................... 3 DC Motor Belt Drive PRE-INSTALLATION CHECKLIST ................................................................................................... 4 WHAT IS INCLUDED ........................................................................................................................
PAGE 2
INTRODUCTION INTRODUCTION PRE-INSTALLATION PRE-INSTALLATIONCHECKLIST CHECKLIST Congratulations on your purchase of Skylink Garage Door Opener, a garage door opener with many innovative features. Features include extremely quiet operation with DC motor; automatic force adjustment so the door can be closed with just the right amount of force, not overpowered; state of the art safety reversal systems that protect your family and property near the door.
PAGE 3
WHAT WHATISISINCLUDED INCLUDED WHAT IS INCLUDED The garage door opener and all accessories are packaged in one carton.
PAGE 4
IMPORTANT IMPORTANTINSTRUCTIONS INSTRUCTIONS WHAT IS INCLUDED BAG B Rail Assembly To reduce the risk of severe injury or death: 1. READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS. B2 x 1 Bolt B1 x 2 Bolt 2. Check with the door manufacturer to determine if additional reinforcement is required to support the door prior to installation of the garage door opener. B3 x 1 Locknut 3. Install garage door opener only on a properly balanced garage door. An improperly balanced door could cause serious injury.
PAGE 5
ASSEMBLE ASSEMBLETHE THET-RAIL RAIL ASSEMBLE THE RAIL Please note the “ 1. Connect the Rail Sections ” marking on the trolley which indicates this side to the door. Align the 6 Rail sections on the floor. Connect the rails together by sliding the taped ends to the untapped ones. 2. Install the Trolley Assembly Slide the trolley from the back of the rail as shown. 3. Install the Idler Pulley Insert the two spacers (C3) in the top and bottom of the slot.
PAGE 6
ASSEMBLE THE RAIL ASSEMBLE THE RAIL B1 (x2) 5. Attach the Rail to the Opener Raise the rail so the rail assembly can sit on the motor unit. Insert the sprocket assembly into the shaft of the motor. Tighten the sprocket assembly by 2 screws. Tighten the rail sections by 2 screws and mounting brackets on the motor unit. Insert a bolt to the stop bolt hole and secure it with nut. 8. TIghten the Belt Connect the 2 ends of the turnbuckle assembly together.
PAGE 7
INSTALL INSTALLTHE THEHEADER HEADERBRACKET BRACKET ASSEMBLE THE RAIL Remove the “U” pin from the turnbuckle after tighten the belt tension properly. 1. Mark the Door Centerline Close the door from inside the garage and mark the vertical centreline of the door on the wall and the top door panel. 9. Attaching the Sprocket Cover Squeeze the cover slightly and insert the 2 tabs on the cover in the slots on the motor unit. Sectional Door “U” Pin Jamb Door 2.
PAGE 8
INSTALL THE HEADER BRACKET INSTALL THE HEADER BRACKET 3. Attach a 2x4 (if necessary) 5. Position The Opener If the calculated header bracket is above the door header, attach a 2x4 between two studs to install the header bracket. Position the pulley bracket against the header bracket. Use lag screws (not included) to attach the 2x4. Door header Position the opener on the floor with packaging material as protective base. 4.
PAGE 9
HANG HANGTHE THE OPENER OPENER HANG THE OPENER 1. Raise the Opener 2. Attach the Hanging Brackets Raise the opener onto a stepladder. Use extra spacers on top of the ladder if the ladder is not tall enough. Hanging brackets should be angled to provide rigid support. Measure the distance from the motor unit to the structural support. Cut and bend the hanging brackets as required. D3 (x2) Sectional Door Carefully raise the door to the fully open position.
PAGE 10
INSTALL INSTALLTHE THEDOOR DOOR BRACKET BRACKET INSTALL THE DOOR BRACKET One-Piece Wood Doors Top of Door Door Bracket Location Door arm connects directly to vertical reinforcement Sectional Wood Doors Bolt 5/16 x 2” (8 x 50 mm) (not included) For wood doors, drill 5/16” (8 mm) holes through the door and secure bracket with 5/16 x 2” (8 x 50 mm) carriage bolts, lock washers and nuts (not included).
PAGE 11
INSTALL INSTALLTHE THEDOOR DOORARMS ARMS INSTALL THE DOOR ARMS 1. Attach Emergency Release Rope 3. Connect the Door Arm to the Trolley Thread the red rope through the hole in the trolley release handle and tie an over-hand knot. Leave the trolley release lever in the released position until further testing is completed. Engaged Released Sectional Door One-piece Jamb Door Connect the straight door arm to the trolley with clevis pin and hitch pin.
PAGE 12
TM INSTALL ATOMS INSTALLTHE THE WALL WALL BUTTON/CONSOLE CONSOLE/LCD WALLFOR CONSOLE INSTALL THE WALL CONSOLE/LCD WALL CONSOLE 1. Location Install LCD Wall Console on ATOMS+ Place the wall console or LCD wall console at least 5’ (1.5 m) above the finished floor or the topmost step. 3a. Secure the mounting bracket with two screws. TM 3b. Slide the wall console onto the mounting bracket until you hear a click. Screw 5 ft (1.5 m) Install Wall Console on ATOMS 4.
PAGE 13
CONNECT TOPOWER POWER CONNECT THE THE OPENER OPENER TO CONNECT THE OPENER TO POWER 3. Permanent Wiring/Remove the Power Cord 1. Connect AC Power Plug motor unit into grounded outlet. If a grounded outlet is not available, contact a qualified electrician to install a proper outlet. DO NOT ACTIVATE THE OPENER UNTIL INSTRUCTED. 4. Permanent Wiring/Remove the Bushing 2. Permanent Wiring/Remove Cover Be sure the power cord is unplugged. Cut the cord about 6” (15 cm) above the bushing.
PAGE 14
INSTALL INSTALLSAFETY SAFETYBEAM BEAMSENSOR SENSOR INSTALL SAFETY BEAM SENSOR 3. Mounting the Sensor on the Door Track Slide (1) and clip (2) the mounting bracket onto the garage door track. Ensure the sensor is mounted between 4” (10 cm) and 6” (15 cm) above the ground. 1 2 Follow the same procedure to install the sensor on the other track ensuing the sensors are facing each other. Important Information: The safety beam sensor can detect obstacles in the path of its invisible beam.
PAGE 15
INSTALL SAFETY BEAM SENSOR INSTALL SAFETY BEAM SENSOR 7. Testing with Obstruction With the sensors properly aligned, place an obstacle in the path of the beam. Press the [SET] button once on the Master sensor, the Master sensor’s blue LED should be on, the Slave sensor’s red LED should be off. NOTE Remove the spring bracket from the mounting bracket if installing to the wall or floor. 1. Slide the sensor from the mounting bracket. 2. Slide the spring bracket from the mounting bracket. 2 3 3.
PAGE 16
INSTALL SAFETY BEAM SENSOR INSTALL SAFETY BEAM SENSOR 2. Mount the shielded Wireless Safety Beam sensor back to back on the door tracks. 5. Once the Wireless Safety Beam sensor is programmed, both the green LED on the Radio Module and the blue LED on the Wireless Safety Beam sensor will flash once. This is indicating you have successfully programmed the Wireless Safety Beam sensor to the Radio Module.
PAGE 17
INSTALL SAFETY BEAM SENSOR INSTALL SAFETY BEAM SENSOR
PAGE 18
INSTALL SAFETY BEAM SENSOR INSTALL SAFETY BEAM SENSOR
PAGE 19
INSTALL SAFETY BEAM SENSOR TM PROGRAMMING GUIDE – LCD WALL CONSOLE (ATOMS+ ONLY) Program your garage door opener with following Option 1 or Option 2. Option 1: from the Wall Console While programming, the  and  buttons can be used to move the door as needed. 1. Connect the opener to an approved power source. The dot in the LED display stays on. 2. Press and hold button on the wall console for 5 seconds until the LCD display shows the number “1” and up and down arrows are flashing. 3.
PAGE 20
TM PROGRAMMING GUIDE – LCD WALL CONSOLE (ATOMS+ ONLY) 12. The LCD display will flash the number “4”. 13. Press the [ ] button again to close the garage door. The flashing “4” will change to solid. 14. The garage door opener will beep once when door is fully closed and the display will show “F”. 15. Press [  ] button to confirm. 16. The LCD display will flash the remote icon. 17. Program a Remote: Within 30 seconds, press any button on the remote that you would like to program to the opener.
PAGE 21
PROGRAMMING GUIDE - ATOMS TM PROGRAMMING GUIDE - ATOMS & ATOMS+TM TM & ATOMS+TM Option 2: from the Garage Door Opener While programming, the  and  buttons can be used to move the door as needed. A. Set Up Travel Limit and Open/Close Force 1. Connect the opener to an approved power source. The dot in the LED display stays on. 12. The LED display will show the number “4”. 13. Press the wall button again to close the garage door to its fully closed position. 14. The LED display will turn off.
PAGE 22
PROGRAMMING GUIDE - ATOMS TM & ATOMS+TM PROGRAMMING GUIDE - ATOMS TM & ATOMS+TM C. Keypad Initial Setup D. Erasing all the Remote Controls from Opener The factory default PIN is 0 0 0 0. It will be used during the keypad initial setup. After you set your own PIN, you will need to use your current PIN instead of 0 0 0 0 in below steps. Note: To erase any unwanted remote controls, first erase all remotes. 1. FOR SINGLE DOOR: A. Enter 0 0 0 0 and * . B. Enter the new PIN (2 to 8 digit password) and * .
PAGE 23
SAFETY TEST OPERATION
PAGE 24
OPERATION OPERATION
PAGE 25
OPERATION OPERATION TM SET-UP Auto closer * on ATOMS (Deluxe Wall Console) SET-UP Auto closer * on ATOMS+TM (LCD Wall Console) The opener has the option to program how long the door should be closed after it has been opened. Press the large button on the wall console to activate the garage door opener. 1. Press and hold 5 seconds. On the wall console there are 3 additional features: 1. Light feature. button for 2. Lock feature. 3. Door closer timer.
PAGE 26
MAINTENANCE MAINTENANCE Lithium battery CR-2032 included.
PAGE 27
BACKUP BATTERY NOTE • These steps must be performed in this exact order very carefully to prevent a short in the battery by accident. Connecting the battery backup unit to the garage door opener unit   Connect the 2-wire harness to the garage door opener unit. Insert the 2-wire harness to the battery backup unit.
PAGE 28
55 56
PAGE 29
44 42 42 41 belt 57 60 58 5860
PAGE 30
PROGRAMMING TO THE INTERNET HUB * - Not application for ANR series LEARN WIRELESS CONTROL   Press the [Set] button for one second. The LED display will show the letter “P”.
PAGE 31
ACCESSORIES FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation. WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
PAGE 32
LIMITED WARRANTY CUSTOMER SERVICE Skylink Group (the Company) warrants to the original purchaser that products delivered hereunder will be free of defects in material and workmanship for the period listed below from the date of purchase.