www.skylinkhome.com Emergency Dialer DIAL-ALERT TM MODEL: AD-105 If you would like to order Skylink’s products or have difficulty getting them to work or download information and user manual, please : 1. visit our FAQ section at www.skylinkhome.com, or 2. email us at support@skylinkhome.com, or 3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
SKYLINK TECHNOLOGIES INC. Your Guide to the Emergency Dialer DIAL-ALERT TM MODEL: AD-105 TABLE OF CONTENTS PACKAGE CONTENTS............................................................................................4 OVERVIEW.....................................................................................................5-6 INSTALLATION..............................................................................................................7-9 LIGHTS AND SOUNDS.....................................
PACKAGE CONTENTS All materials required for installation are included with this package 1 1 1 1 1 Dial-Alert (AD-105) Telephone Line antenna (installed) AC adapter 9 volt alkaline battery OVERVIEW The AD-105 emergency dialer can call multiple phone numbers during an emergency situation and it will playback prerecorded messages. There are 2 operating modes you can set up in the AD-105 dialer.
OVERVIEW Dial Alert AD-105 must work with the specific sensors listed below. Ensure only the listed sensors are used with the AD-105, otherwise, the communication between the sensors and the Dial Alert may not function properly. If you have a Skylink wireless device or sensor that is not listed below, and uncertain whether it can work with your AD-105, please contact our customer support team.
INSTALLATION 2. Thread the telephone line through the top hole in the back of the unit and plug it into the "LINE" jack. If you want to have an answering machine on the same line as the dialer, thread the phone line through the bottom hole in the back of the unit and plug it into the "PHONE" jack of the dialer. The phone line(s) must be inserted through the back of the unit before it is attached to the wall. 3.
LIGHTS AND SOUNDS STANDARD PROGRAMMING Below is an explanation of the lights and sounds of the Dial-Alert LIGHTS ACPWR light on ACPWR light off LOBATT. light off LOBATT. light on ARM light on ARM light off Keypad backlight dialer is being powered by AC adapter. dialer is not receiving any AC power. backup battery is connected and working. backup battery is weak, battery needs to be replaced. the dialer is in armed condition.
STANDARD PROGRAMMING RECORD A VOICE MESSAGE You must record a message and program at least one phone number in order for the Dial Alert to work. The voice recording procedure is different between the 2 operating modes, SC-001 Mode and Sensor Mode. To record a voice message under SC-001 Mode: 1. Enter the current password (factory default password is 0000), then press [PROG], display will show [P] meaning you are now in programming mode. 2. Enter [3] which represents voice recording. You will see [P3 0 40].
STANDARD PROGRAMMING STANDARD PROGRAMMING Do not program the phone number to police or fire dept directly into your Dial-Alert unless you have checked with your local authorities. Please also inform all the recipients that their phone numbers have been programmed into your dialer, so they know exactly what happens when they receive your emergency message. 1. Enter the current password (factory default password is 0000), then press [PROG], display will show [P] meaning you are now in programming mode. 2.
OPERATIONS SC-001 Mode When the display shows “rEAdy”, that means the unit is in standby mode. It will dial when it receives a panic signal from the alarm panel, or its own panic button is pressed. It will dial the programmed phone numbers and playback the voice message. It is not necessary to put the AD-105 in arm mode. Once the display shows “rEAdy”, the AD-105 will respond if it receives a command to dial out.
ADVANCED PROGRAMMING ADVANCED PROGRAMMING Changing Password Erase Programmed Panic Transmitters / Alarm Panels / Sensors Password is required for programming purposes. Factory default is 0000. To change the setting, follow the instructions below. You may erase the programmed wireless devices, panic transmitter, alarm panels and wireless sensors. You cannot erase a specific device, you must erase all the devices and then program the ones that you would like to keep. 1.
ADVANCED PROGRAMMING ADVANCED PROGRAMMING 3. Enter [1] to disable universal dial tone meaning a proper dial tone must be presented before dialing, or [2] to enable universal dial tone, so the Dial Alert will dial regardless of the dial tone. 4. If the new setting is accepted, it will emit 2 beeps. If you don’t hear 2 beeps, that means the setting is not accepted, retry again. 1.
ADVANCED PROGRAMMING BATTERY MAINTENANCE CONNECT THE DIAL-ALERT WITH YOUR EXISTING ALARM SYSTEM You may connect your existing alarm system with the Dial-Alert so that the dialer will be triggered by your alarm system when it is activated. There are 2 ways you can connect your dialer with your existing alarm system. 1. Connect the dialer with the alarm system using hard wire (normally closed). 2. Connect the dialer with the alarm system using the Audio Sensor (AS-101). PANEL OR SENSOR N.C..
ADDITIONAL ACCESSORIES Additional sensors and transmitters as well as add on accessories are available to work with your Dial-Alert.
ADDITIONAL ACCESSORIES Audio Sensor (AS-101) - Detects alarm sound from existing security system alarm; sends signal to Dial-Alert. - Eliminates need for monitoring service.