Instructions / Assembly

TOTAL PROTECTION SYSTEM
1. Enter the MPIN (Master Personal Identification Number) on the control
panel (SC-001).
2. Press [B] on the control panel.
3. If you are programming the tramsmitter to the security control panel
SC-001, press [5] on the control panel. This is the zone where the
keypad transmitter will communicate with the security control panel.
ONLY PROGRAM THE KEYPAD TRANSMITTER TO THE DESIGNATED
ZONE, OTHERWISE THE TRANSMITTER WILL NOT WORK PROPERLY.
4. Press [*] within 8 seconds on the control panel, you will hear a long
beep from the control panel.
5. Activate the keypad transmitter by pressing the panic button (red key)
on the keypad transmitter. The “ON” light on the transmitter will be on.
You will hear a long beep from the control panel, the keypad transmitter
will now communicate with the control panel.
You can use the keypad transmitter to arm the security system in
different arming sequences, and disarm the system. Please refer to the
user’s instructions of the main system for details.
Here is a summary of how to arm the system in different arming
sequences:
1. PROGRAMMING
2. OPERATION
Arming Sequence
Away Sequence [Password] [B] [C]
Home Sequence [Password] [C]
Night Sequence [Password] [A] [B]
Chime Sequence [Password] [A] [#]
Disarm [Password] [#]
Panic [O] – Red Panic Button
Note: [Password] can be the master password or secondary password.
In order to erase any unwanted transmitters, you must erase all of them,
then reprogram each keypad transmitter you wish to use.
Follow the instructions below to erase a keypad transmitter from SC-001
control panel.
1. Enter the master password
2. Press [B]
3. Press [5]
4. Press [*]
5. Do not activate any keypad or keychain transmitter for 30 seconds
after [*] was pressed.
6. You have now successfully erased all the transmitters in zone 5.
Please re-program the transmitters you would like to use by
following the programming instructions.
Refer to Changing Password to assign new password (master and
secondary) to change existing password.
AAA+
TM
Home Smart Center
Follow the instructions below to program keypad transmitter to the
AAA+
TM
Control Panel.
There are 5 locations you can program the keypad transmitter to (you
can program max 5 keypad transmitters to the AAA+ Control Panel),
select one location that is not occupied then you can program the
keypad transmitter to this location.
1
2
3
4
[PROG]
[MPIN]
Enter
Programming
mode
Enter master
password to
programming
mode
3 beeps for valid
password. 1 long
beep for invalid
password.
[4]
Select learn
remote
program-
ming
After [4] is entered,
some zone LEDs will
flash or stay off.
The zone LEDs
represent whether
that zone is already
occupied by another
remote.
** See Table A below.
[6] to [0]
Select remote
location
(Max. 5
remotes)
Select a remote
location [6], [7],
[8], [9] or [0].
After you have
selected the remote
location, that zone
LED will be on.
Trigger
remote
Once the signal
is transmitted
to the Control
Panel, that
signal which will
be stored.
You will hear
[Device X Accepted],
where “X” is the
remote location.
Activate the
remote by
pressing
any one of
the buttons.
Step Keys Function Description Note
1. PROGRAMMING
ZONE LED DESCRIPTION
Off Zone is not occupied by any remote
Flashes twice This zone is occupied by another remote.
Programming another remote to this zone will
overwrite the previous remote.
Flashes once This zone is occupied by a control module (Optional).
You can still program a remote to this zone, and it will not
overwrite the control module you have in this zone.
Flashes once, This zone is occupied by a remote AND a control module.
then twice If you program another remote to this zone, it will overwrite
the previous remote, but not the control module.
** Table A: Zone LED status for learning keychain/keypad remote(s).
Remote [6] is represented by zone LED 1
®
ZONE
LED
1 6
2 7
3 8
4 9
5 0
REMOTE
LOCATION
3. ERASE KEYPAD TRANSMITTERS