Instructions / Assembly

2. OPERATION
1
2
3
[PROG]
[MPIN]
Enter
Programming
mode
Enter master
password to
programming
mode
3 beeps for valid
password. 1 long beep
for invalid password.
[0]
Select erase
remote
programming
After [0] is entered,
some zone LEDs will
flash or stay off. The
zone LEDs represent
whether that zone is
occupied by any
remote.
** See Table B below.
Select
remote
location
you would
like to
erase
Af ter you have selected
the remote location, you
will hear 3 beeps and
verbal confirmation
[Device X Empty
Memory], where X is the
remote location you
have selected.
To erase
an
occupied
remote,
press [6]
to [0].
Select a
remote
location [6],
[7], [8], [9]
or [0].
Step Keys Function Description Note
ZONE LED DESCRIPTION
Off Zone is not occupied by any remote
Flashes twice This zone is occupied by a remote. You may select this
zone to erase this remote.
Flashes once This zone is occupied by a control module (Optional).
THIS IS NOT A REMOTE CONTROL, THEREFORE,
SHOULD NOT BE ERASED
Flashes once, This zone is occupied by a remote AND a control module.
then twice You may select this zone to erase the remote.
You can use the keypad transmitter to arm, disarm or activate the panic
for the AAA+ Control Panel.
Here is a summary of how to operate different modes on AAA+ Control
Panel.
Arm [Password] [B] [C]
Disarm [Password] [#]
Panic [O] – Red Panic Button
Refer to AAA+ Home Smart Center User’s Instructions to erase keypad
transmitter from the AAA+ Control Panel.
Follow the instructions below to erase keypad remotes.
** Table B: Zone LED status for erasing keychain/keypad remote(s).
3. ERASE KEYPAD TRANSMITTERS
To change a password, you must have the master password, which is
the password that allows setting additional password. Up to 3
secondary passwords can be assigned to each keypad transmitter.
Therefore, the total number of password is:
1 Master Password (Programming and Operation)
3 Secondary Password (Operation Only)
To change the master password, follow the instructions
below:
To change the password, follow the instructions below:
1. Enter the current password (000 is the factory default password)
2. Press [*]
3. Press [0]
4. Press [*]
5. Enter the new password (password can be from 3 to 6 digits)
6. Press [*]
If the keypad transmitter accepts the new password, it will a long beep.
If it emits 3 short beeps, it means the password has not been changed.
Start again from step 1.
To assign or change secondary password, follow the
instructions below:
1. Enter the current master password (000 is the factory default
password)
2. Press [*]
3. Press the numeric key that represents the secondary password
user, either [1], [2], or [3].
4. Press [*]
5. Enter the new secondary password (password can be from 3 to 6
digits)
6. Press [*]
If the keypad accepts the new secondary password, it will emit a long
beep. If it emits 3 short beeps, it means the password has not been
assigned or changed. Start again from step 1.
To delete a secondary password, follow the instructions below:
1. Enter the current master password (000 is the factory default
password)
2. Press [*]
3. Press the numeric key that represents the secondary password
user, either [1], [2], or [3].
4. Press [*]
5. Press [*] again
If the secondary password is successfully deleted, it will emit a long
beep. Otherwise, start from step 1 again.
CHANGING PASSWORD
Refer to Changing Password to assign new password (master and
secondary) to change existing password.
The Keypad Transmitter operates on two 3 volt lithium batteries (CR2032).
This transmitter comes with the batteries already installed. It is time to
replace the batteries when the low battery indication is on. Low battery
condition is indicated by the “LO BATT” light on
when the keypad is activated.
To replace the batteries:
1. Remove the keypad transmitter from the wall.
2. Undo the screw on the back of the unit.
3. Use a screwdriver to open the battery compart-
ment by rotating it.
4. Remove the batteries from the battery com-
partment.
5. Place the new batteries in position. See diagram.
6. Close the battery compartment and reinsert the
screw.
+
BATTERY