www.skylinkhome.com Emergency Dialer DIAL-ALERT TM MODEL: AD-103 If you would like to order Skylink’s products or have difficulty getting them to work or download information and user manual, please : 1. visit our FAQ section at www.skylinkhome.com, or 2. email us at support@skylinkhome.com, or 3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
–2– –19– Pager Pause Dialing Sequence Universal Dial Tone [PIN]+[PROG]+[8] [PIN]+[PROG]+[9] Erase Control Panel [PIN]+[PROG]+[7] [PIN]+[PROG]+[6] Phone Number Program Control Panel Voice Message Recording [PIN]+[PROG]+[3] [PIN]+[PROG]+[4] [1] - Off, [2] - On [2] - Finish dialing first phone number then begins second number [1] - Dials each number once, then redial if necessary, [1] - 1 sec, [2] - 2 seconds.......
BATTERY MAINTENANCE The AD-103 Dial-Alert comes with 1 battery that at some point you may have to replace: One 9 volt alkaline battery for the Dial-Alert Recommendation: Test your Dial-Alert periodically to ensure that the battery is working. Dial-Alert Battery The Dial-Alert comes equipped with a 9V backup battery in case the electrical power is interrupted for any reason. When the dialer backup battery is low, the LOBATT. light goes on. To replace the dialer backup battery: 1.
PACKAGE CONTENTS 1 1 1 1 1 Dial-Alert (AD-103) Telephone Line antenna (installed) AC adapter 9 volt alkaline battery 9 VOLT All materials required for installation are included with this package ADVANCED PROGRAMMING 2. Enter [8], display now shows [P8 2], the most right digit represents the dial sequence. 3. To change the setting, enter either 1 or 2, where 1 is Dial Sequence 1, and 2 is Dial Sequence 2. 4. If the new setting is accepted, it will emit 2 beeps.
ADVANCED PROGRAMMING Erase Programmed Control Panel You may erase the programmed control panel. If you have multiple control panels programmed, you cannot erase a specific control panel, you must erase all the control panels and then program the ones that you would like to keep. To erase all the control panels, follow the instructions below. 1. Enter the current password (factory default password is 0000), then press [PROG], display will show [P] meaning you are now in programming mode. 2.
INSTALLATION ADVANCED PROGRAMMING The Dial-Alert is installed using the screws provided. We have also included double sided tape, to use for temporary installation while you are positioning the dialer. Once the dialer is positioned correctly, install it permanently with screws. We have also included wall anchors and a template to help position the screws correctly. How to use the template: 1. Cut the template in the correct position 2. Screw part way into the surface where the holes are marked 3.
OPERATIONS When the display shows “rEAdy”, that means the unit is in standby mode. It will dial when it receives a panic signal from the alarm panel, or its own panic button is pressed. It will dial the programmed phone numbers and playback the voice message. Once the display shows “rEAdy”, the AD-103 will respond if it receives a command to dial out. INSTALLATION 2. Thread the telephone line through the top hole in the back of the unit and plug it into the "LINE" jack.
STANDARD PROGRAMMING INSTALLATION Speaker On/Off Switch The speaker must be on during programming and recording the voice message in order to use the playback feature. For security purposes, the speaker may be turned off after programming to allow for silent dialing when the dialer is activated. The On/Off switch for the speaker is located on the lower right corner of the circuit board. The default setting for the speaker is "On".
STANDARD PROGRAMMING PROGRAM A PHONE NUMBER You may program up to 9 different phone numbers. Follow the instructions below to program phone numbers. 1. Enter the current password (factory default password is 0000 ), then press [PROG], display will show [P] meaning you are now in programming mode. 2. Enter [4] which represents phone number programming. You will see [P4 PHonE 1]. The number on the most right represents the phone number, from Phone 1 to Phone 9. 3.
STANDARD PROGRAMMING STANDARD PROGRAMMING There are a few programming steps you must perform before the dialer can operate. Please follow the instructions below to program these fields, including: 3. Enter [0] to [5] to select which message you would like to record. If you enter [3], you should see [P3 3 05].
