Home Security System User Manual

ManualsBrandsSkyLink ManualsHome Safety ProductPS-434A

i. Enter the current MPIN (Master Identification Number) in the

Security Control Panel (SC-001)

ii. Press [B].

iii. Press the number key to identify which zone to add the Motion

Sensor to [1, 2, 3, 4]. We recommend you program the motion

sensor to zone 2. The zone light will flash for eight seconds.

iv. While the zone light is flashing, press [*].

v. While the zone light is flashing, press the Learn Button inside the

battery compartment (diagram 1) of the Motion Sensor in order to

activate it. You will hear a long beep if the motion sensor is

“learned” to the control panel. The zone light will stop flashing and

the remote sensor will now communicate to that zone.

2. SET UP THE MOTION SENSOR

1. INTRODUCTION

Motion Sensor

Model PS-434A

The Motion Sensor is designed to monitor movement around your house.

It can be placed either indoor or outdoor.

In this package, you should find a

Motion Sensor (battery included),

ball-head joint and screws.

Please follow the instructions below to setup your motion sensor.

2 pcs 3 x 18 screws

(Included)

Motion Sensor

(battery included)

Ball-head joint

The sensitivity of the motion sensor is adjustable. Change the setting by

placing the connector on either the ”High” or “Low” position. When the

sensitivity is set to “Low”, more movement is required to trigger the

sensor. It is recommended to set the

sensitivity to “Low” and perform a

“Walk Test” (Described in Section 3 -

“Walk Test”). If the walk test result is

satisfied, the sensitivity does not

require to be adjusted further. If the

walk test result shows the sensitivity

is too low, then you can change the

sensitivity setting to “High”. Please

perform the walk test after changing

the sensitivity setting.

5. SENSOR SENSITIVITY

Sensitivity Connectors on Motion Sensor

A ball-head joint is necessary to mount the sensor at a desire location.

A height of 5-6 ft is recommended, depending on your application. Once

a location is selected, mount the ball-head joint to this location by screws

provided, (see diagram 2). Once the ball-head joint is mounted to the

wall, slide the back of the sensor into the ball-head joint (see diagram 3).

The mounting angle can be adjusted. Please refer to Section 3 “Walk

Test” to determine the best mounting angle.

2. PROGRAM THE MOTION SENSOR TO THE SECURITY CONTROL PANEL

(SC-001)

i. With only the “ON” light lit on the Audio Alarm, press and hold the

learn button located on the bottom of the Audio Alarm.

ii. While pressing down on the button, press the Learn Button inside

the battery compartment (diagram 1) of the Motion Sensor in order to

activate it.

iii. If a connection has been made, the Audio Alarm will stop beeping

and make a continuous tone until the black learn button on the Audio

Alarm is released.

3. PROGRAM THE MOTION SENSOR TO THE AUDIO ALARM (AA-433)

i. Press [L], [5] when in clock mode, the display will show “L5 Id code”.

ii. Within 5 seconds, press the Learn Button inside the battery

compartment (diagram 1) of the Motion Sensor in order to activate

it. The display will return to clock mode once the Motion Sensor

has been learned.

iii. If the Motion Sensor detects any movement, it will trigger the

Emergency Dialer and start dialing the preset phone numbers

(refer to AD-433S, AD-1010, ED-1010 User’s Instruction).

4. PROGRAM THE MOTION SENSOR TO THE EMERGENCY DIALER

(AD-433S, AD-1010, ED-1010)

4. FCC

Diagram 2

Diagram 3

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that

may cause undesired operation.

WARNING:

Changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful inter-

ference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment dose cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Learn button

Insert a 9V alkaline battery to the

motion sensor. The sensor

requires a warm up time of

approx. 45 seconds before it can

function properly.

Insert 9V alkaline battery to the sensor

1. POWER UP

Diagram 1

1. MOUNTING

3. INSTALLING THE MOTION SENSOR

After mounting the sensor at the desired location,

it is important to perform a walk test in order to

determine if the sensor is detecting the things you

want to detect.

In order to control how far the sensor can “see”, this can be done by

adjusting the angle of the sensor. To reduce the detection range, simply

move the sensor downward. To increase the range, move the sensor

up to around 12 degrees. This will give the maximum range. However,

this may not be desired if the sensor is placed outdoors, since a false

trigger may occur if the sensor is set to detect motion in a distance.

Disarm the control panel or dialer before you perform the work test, or

you will trigger an alarm (please refer to the user’s instruction of your

receiver)

2. WALK TEST

You should walk in the area that you would like the sensor to monitor. If

movement is detected the red light inside the unit will appear. If the red

light does not appear, adjust the mounting angle accordingly. Perform

the walk test again after 30 seconds. Repeat this procedure until your

motion is detected. There should be no movement in the detected area

during the 30 seconds.

Perform walk test in the undesired

area to ensure movement cannot

be detected.

Tips: The sensor should not face

towards direct sunlight, placing

near heat or cold producing devices

(i.e. A/C or furnance vents, fans,

ovens, heaters etc.) that may

cause false triggers.

12º

Move the sensor

downward to

reduce the range.

Move the sensor up

to around 12 º to give

maximum range.

Summary of content (2 pages)

PAGE 1
Motion Sensor Model PS-434A 1. INTRODUCTION 3. INSTALLING THE MOTION SENSOR The Motion Sensor is designed to monitor movement around your house. It can be placed either indoor or outdoor. In this package, you should find a Motion Sensor (battery included), ball-head joint and screws. 2 pcs 3 x 18 screws (Included) Ball-head joint Motion Sensor (battery included) 1. MOUNTING A ball-head joint is necessary to mount the sensor at a desire location.
PAGE 2
5. WARRANTY If, within one year from date of purchase, this product should become defective (except battery), due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of purchase and a Return Authorization are required. 6. CUSTOMER SERVICE If you would like to order Skylink’s products or have difficulty getting them to work, please : 1. visit our FAQ website at www.skylinkhome.com, or 2. email us at support@skylinkhome.com (reply within 24 hrs), or 3.