Instructions / Assembly

ManualsBrandsSkyLink ManualsElectricalWireless Door/Window Sensor

The sensor must be programmed to the Household Alert

Long Range

Receiver before they can communication. You may program the sensor

to one of the 4 zones. Follow the instructions below;

1. Plug in an AC adapter to the receiver.

2. Power up the Receiver unit. The green LED will be on indicating it

is turn on.

3. Open the back cover and there is a learn button. Press and hold

this learn button for 5 seconds, until both green LED and zone 1

red LED flash. You may now release the learn button.

4. If you would like to program the sensor to zone 1, activate the

sensor while the zone 1 red LED is flashing. Activate the Sensor

by separating the magnetic contact from the sensor.

5. If you would like to program the sensor to other zones, press the

learn button again, until the red LED flashes at the zone you want

to program the sensor to, then activate the sensor.

6. Once the sensor is programmed, the green LED will be steadily on

and none of the red zone LEDs will be on.

Note: Each zone can program up to 4 sensors. If you try to program a

fifth sensor into a zone, the first programmed sensor will be erased.

1. INTRODUCTION

Model WD-434TL

The Door/Window Alert is designed to monitor any door or window

within your house. When the monitored window or door is opened, the

receiver will flash along with alert beeping or alarm.

In this package, you should find a Door/Window Sensor, a magnet, 3V

lithium battery (installed) and other mounting accessories.

Please follow the instructions below to setup your door / window

sensor.

Sensor

Plug in the adapter to the receiver

2. PROGRAMMING

Learn Button

Door/Window Sensor

Magnet

Mounting

Accessories

Separate the magnet from

the sensor, Receiver zone LED

stops flashing.

Test Sensor

After learning the sensor to the Receiver unit, you may test the com-

munication by placing the magnet beside the sensor (where the red

marking is) and remove the magnet from the sensor.

When the magnetic is closed, the

receiver will not beep.

When the magnetic contact is broken (open),

the receiver will beep and zone LED will flash.

1) Zone LED of this sensor will flash.

2) Beeping according to the zone number [Operating mode is set to

“Alert”]. 1 beep for zone 1, 2 beeps for zone 2 and etc, until the

magnetic contact is closed.

Erasing a sensor

You cannot erase a specific sensor. You must erase all sensors from

the receiver, then program the ones you would like to keep. To erase all

the sensors from the receiver:

1. Remove the adapter from the receiver.

2. Open the back cover, press and hold the learn button. Do not release

the learn button until step 4.

3. While holding onto the learn button, plug in the adapter to the receiver.

4. You may release the learn button when the LEDs on the receiver are

on.

5. You have erased all sensors from the receiver.

3. INSTALLATION

2. PROGRAMMING (CONT)

Sensor

Magnet

"Red Marking"

on the side

"Red Marking"

on the side

The transmitters should be mounted on the door frame or window frame

by double sided tape. The magnet should be mounted on the door or

window by either double sided tape or screws. Make sure the magnet is

aligned with the red marking on the transmitter. If the surface of the frame

is flat enough, double-sided foam tape is sufficient, otherwise, it is

recommended to screw the mounting plate to the frame, then apply

double sided tape. After mounting the sensor, if the Skylink logo is

inverted, remove the front cover and rotate it so the Skylink logo is in the

upright position.

Mounting plate

and screws (optional)

Double-sided

foam tape

Sensor

4. OPERATION

There are 3 different operating modes for the Household Alert

Long

Range Receiver.

1) Alert - Beeps when a sensor is activated, corresponding zone LED

will also flash.

2) Alarm - Sounds an alarm when a sensor is activated, corresponding

zone LED will also flash.

3) Off - No audio sound will be emitted when sensor is activated.

Zone LED will flash to indicate the activated

sensor.

To select the operating mode, place the

slide switch on the side at the desired setting:

OFF - No Audio

ALERT - Alert Mode

ALARM - Alarm Mode

Summary of content (2 pages)

PAGE 1
Door/Window Sensor Model WD-434TL 1. INTRODUCTION 2. PROGRAMMING (CONT) The Door/Window Alert is designed to monitor any door or window within your house. When the monitored window or door is opened, the receiver will flash along with alert beeping or alarm. In this package, you should find a Door/Window Sensor, a magnet, 3V lithium battery (installed) and other mounting accessories. Magnet 1) 2) Zone LED of this sensor will flash.
PAGE 2
7. FCC 4. OPERATION (CONT) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Operation Alert When the magnetic contact is broken, such as when the door or window is open, the sensor will send a signal to the receiver. It will beep and the corresponding zone red LED will flash.