User Manual
6.
07 ·
MC3000
· 06
MC3000
QUICK START GUIDE QUICK START GUIDE
Insert round batteries in the empty slots observing correct polarity. Be aware of the battery type!
The display shows the voltage of the correctly inserted batteries and a blinking "PROGRAM[01]"
for them. "#1" refers to the first slot counted from the left, i.e. the slot with slot number button 1,
whereas "[01]" means the program with the program number 01. Note: In the Simple and
Advanced UI modes the device will NOT determine battery chemistry automatically but only issue
a warning at questionable battery voltage levels and for safety reasons refuse to proceed. For
incorrectly inserted batteries the screen continues to display "NO BATTERY" making you realize
that you did something wrong.
1
2
3
4
# V O L T C U R R m A h
1 . 3 3 P R O G R A M [ 0 1 ]
4 . 0 5 P R O G R A M [ 0 2 ]
4 . 0 1 P R O G R A M [ 0 3 ]
3 . 8 3 P R O G R A M [ 0 3 ]
Battery
Slot No.
Operation
Mode
Battery
Voltage
ProgramNo.01-30
How to Make a Program
1
2
3
4
# V O L T C U R R m A h
1 . 4 8 P R O G R A M [ 0 1 ]
3 . 8 5 P R O G R A M [ 0 1 ]
3 . 8 6 P R O G R A M [ 0 1 ]
3 . 8 3 P R O G R A M [ 0 1 ]
B A T T T Y P E :
M O D E :
C A P A C I T Y :
C . C U R R E N T :
# 1 P R O G R A M [ 0 1 ]
L i I o n
C h a r g e
O F F
1 . 0 0 A
1
Press SNB to
Go to SPV
Example:
In slot #1, we insert NiMH battery. Let’s make program[02] for this battery (Discharge,
discharging current: 0.8A).
B A T T T Y P E :
M O D E :
C A P A C I T Y :
C . C U R R E N T :
# 1 P R O G R A M [ 0 2 ]
L i I o n
C h a r g e
O F F
1 . 0 0 A
Change to
program[02]
B A T T T Y P E :
M O D E :
C A P A C I T Y :
C . C U R R E N T :
# 1 P R O G R A M [ 0 2 ]
L i I o n
C h a r g e
O F F
1 . 0 0 A
B A T T T Y P E :
M O D E :
C A P A C I T Y :
C . C U R R E N T :
# 1 P R O G R A M [ 0 2 ]
N i M H
C h a r g e
O F F
1 . 0 0 A
Continue on next page
B A T T T Y P E :
M O D E :
C A P A C I T Y :
C . C U R R E N T :
# 1 P R O G R A M [ 0 2 ]
N i M H
C h a r g e
O F F
1 . 0 0 A
Change to
Discharge
M O D E :
C A P A C I T Y :
C . C U R R E N T :
D . C U R R E N T :
# 1 P R O G R A M [ 0 2 ]
D i s c h a r g e
O F F
O F F
- 0 . 4 0 A
M O D E :
C A P A C I T Y :
C . C U R R E N T :
D . C U R R E N T :
# 1 P R O G R A M [ 0 2 ]
D i s c h a r g e
O F F
O F F
- 0 . 4 0 A
C U T V O L T :
C U T T E M P :
C U T T I M E :
S A V E T O :
# 1 P R O G R A M [ 0 2 ]
O F F
4 5 C
1 8 0 m i n
[ 0 2 ]
M O D E :
C A P A C I T Y :
C . C U R R E N T :
D . C U R R E N T :
# 1 P R O G R A M [ 0 2 ]
D i s c h a r g e
O F F
O F F
- 0 . 8 0 A
C A P A C I T Y :
C . C U R R E N T :
D . C U R R E N T :
# 1 P R O G R A M [ 0 2 ]
O F F
O F F
- 0 . 8 0 A
C . R E S T I N G : O F F
Navigate down
Confirm, then
Navigate down
Before starting the slots, make sure that a proper program is assigned to them. For this, short-
press the slot number buttons to transfer to Slot Programming View where you can change the
program number, or check & edit the respective program settings (see "How to Make a
Program"). Long-press the ENTER-button to confirm any changes made and to transfer back to
Total Overview.
Finally, long-press SNB of the ready slots to start their programs one after the other.
Alternatively, short-press ENTER to start all the ready slots at once.
7.
8.
Edit settings
of program[02]
Access battery type
B A T T T Y P E :
M O D E :
C A P A C I T Y :
C . C U R R E N T :
# 1 P R O G R A M [ 0 2 ]
L i I o n
C h a r g e
O F F
1 . 0 0 A
B A T T T Y P E :
M O D E :
C A P A C I T Y :
C . C U R R E N T :
# 1 P R O G R A M [ 0 2 ]
N i M H
C h a r g e
O F F
1 . 0 0 A
Change
battery type
Confirm selection
Access
operation mode
Continue on next page
Save To (optional),
Press and hold to Save settings
B A T T T Y P E :
M O D E :
C A P A C I T Y :
C . C U R R E N T :
# 1 P R O G R A M [ 0 2 ]
N i M H
D i s c h a r g e
O F F
1 . 0 0 A