Universal Battery Charger & Analyzer NiMH / NiCd / NiZn / Eneloop / RAM / Lithium-Ion / LiIo4.35 / LiFePO4 / LTO Instruction Manual This content is subject to change. Latest version can be downloaded from www.skyrc.com If you have any question about this document, please contact SkyRC by sending a message to info@skyrc.cn All Rights Reserved. Manufactured by SKYRC TECHNOLOGY CO., LTD. www.skyrc.com 2018 SkyRC Technology Co., Ltd. All Rights Reserved. 7504-0680-05 [Version 1.
TABLE OF CONTENTS INTRODUCTION INTRODUCTION 01 Welcome WARNING AND SAFETY PRECAUTIONS 03 QUICK START GUIDE 04 BATTERY KNOWLEDGE 10 BATTERY VOLTAGES 11 TOTAL OVERVIEW 12 GLOBAL SETUP VIEW 14 SLOT PROGRAMMING VIEW 17 SLOT OPERATION VIEW 24 Charging batteries is usually a primitive, boring task. Can’t fool your friends, it still is. In fact, this charger merely knows three elementary routines: charge, discharge, rest. However ...
INTRODUCTION WARNING AND SAFETY PRECAUTIONS User Interface The UI can be switched between Dummy, Simple and Advanced menu modes. The advanced menu lets the user control every single technical parameter of the operation mode whereas a simpler mode with less options may be more convenient for quick everyday usage.
QUICK START GUIDE QUICK START GUIDE Do not overcharge nor over discharge batteries. Recharge drained batteries as soon as possible. Remove all batteries and unplug the charging unit from the power source when not in use. Opening, disassembling, modifying, tampering with the unit may invalidate its guarantee, check warranty terms. # VOLT TYPE CURR 1 1.33 NIMH: 0.7A 2 3.99 LIIO: 0.7A 3 NO BATTERY 4 NO BATTERY QUICK START GUIDE # 1 2 3 4 Read the Warning and Safety Precautions first and follow them.
QUICK START GUIDE QUICK START GUIDE 6. Insert round batteries in the empty slots observing correct polarity. Be aware of the battery type! The display shows the voltage of the correctly inserted batteries and a blinking "PROGRAM[01]" for them. "#1" refers to the first slot counted from the left, i.e. the slot with slot number button 1, whereas "[01]" means the program with the program number 01.
QUICK START GUIDE # 1 2 3 4 VOLT 1.48 3.85 3.86 3.83 QUICK START GUIDE CURR mAh PROGRAM[02] PROGRAM[01] PROGRAM[01] PROGRAM[01] INFO MESSAGE #1: Saved to [02] #2: PROGRAM[01] #3: PROGRAM[01] #4: PROGRAM[01] The following illustration shows how the five common views of the user interface are interconnected: SOV Slot Operation View DDV Diagram Drawing View SNB Start All # 1 2 3 4 VOLT CURR mAh Processing... Processing... Processing... Processing... Programs Starting # 1 2 3 4 VOLT CURR 1.45 -0.
BATTERY KNOWLEDGE BATTERY VOLTAGES What Does 0.5C, 1C, -C/4, Etc Mean? It is a short way of specifying charge transfer rates as function of battery capacity. Substitute the nominal capacity for "C", divide by 1h, then multiply with the factor. For example, 0.3C for a 2100mAh battery equals a charge rate of 630mA or 0.63A (= 2100mAh/1h * 0.3 ), -C/4 or -0.25C for a 3400mAh battery equals discharging it at 0.85A.
TOTAL OVERVIEW (TOV) TOTAL OVERVIEW (TOV) How to get there — Depending on the situation, depressing the STOP button or clicking it once, twice, or thrice will get you back to TOV. How to exit — In TOV, remove all batteries and unplug the device from mains. # VOLT CURR mAh 1 NO BATTERY 2 4.18 0.00 3467 3 4.20 2.99 1289 4 3.75 PROGRAM[05] • Clicking the SNB of an inactive slot will get you to its SPV. • Clicking the SNB of an active slot will get you to its SOV, whereas depressing it will stop the slot.
GLOBAL SETUP VIEW (GSV) GLOBAL SETUP VIEW (GSV) How to get there — In TOV, if all slots are inactive, depressing the STOP button will transfer to GSV. How to exit — In GSV, pressing the STOP button once or twice will cancel changes, quit the view and return to TOV. SETUP Language: English UI Mode: Dummy Names: Default Temp Unit: C Dummy Lets the user confirm NiMH/LiIon as the presently supported coupling of the two most common rechargeable battery types in the Dummy UI Mode.
GLOBAL SETUP VIEW (GSV) SLOT PROGRAMMING VIEW (SPV) LCD Contrast Lets the user adjust the contrast of the LCD screen. How to get there — In TOV, clicking the SNB of an inactive slot will transfer to SPV. Names How to exit — Pressing the STOP button will eventually lead back to TOV without any changes saved. This option controls the program naming format in TOV. By default and for simplicity, programs are listed with their respective program numbers only.
SLOT PROGRAMMING VIEW (SPV) SLOT PROGRAMMING VIEW (SPV) The controls in SPV are as follows: • Pressing the UP or DOWN button navigates through the items, or lets the user make a selection. • Clicking the ENTER button enters an option (=Enter), confirms a selection (=OK), or navigates through all items from top to bottom (=Next). • Depressing the ENTER button saves all changes and then transfers to TOV (=Save&Exit).
SLOT PROGRAMMING VIEW (SPV) SLOT PROGRAMMING VIEW (SPV) • Discharge - Primitive operation mode which does nothing but 1 discharge routine, D, eventually followed by a rest phase, i.e. D>. Maximum discharge current is -2.00A per slot for all battery types, restrictions apply. Useful for analyzing the remaining amount of electric charge stored in the battery. • Cycle - Automatically repeats the three distinct routines after the specified pattern.
SLOT PROGRAMMING VIEW (SPV) SLOT PROGRAMMING VIEW (SPV) CUT TEMP The temperature cut-off. It is the temperature of the battery, or more precisely the temperature at the slot sensor, at which the program will stop with an abnormal program termination message. A safety option, it can protect batteries against unexpected overheating.
SLOT OPERATION VIEW (SOV) SLOT OPERATION VIEW (SOV) How to get there — In TOV, when there is at least one active slot, clicking its SNB will transfer to SOV. How to exit — In SOV, pressing the ENTER button will return back to TOV. Or, after some period of user inactivity, returns to TOV automatically. #2 LiIon Mode: Charge Capacity: 9mAh Volt: 3.97/4.20V C.Current: 2.99A Volt Shows both the actual battery voltage and the end voltage, i.e.
SLOT OPERATION VIEW (SOV) DIAGRAM DRAWING VIEW (DDV) Total Total time. Shows the elapsed time since the start of the program. In SPV, for long-term cycling make sure to set the parameter of the CUT TIME program option to OFF because CUT TIME is limited to 1 day, whereas the timer of Total can count up to days and days. How to get there — In TOV, if there is at least one active slot, clicking the UP or DOWN button will transfer to DDV.
USER CALIBRATION USER CALIBRATION Very similar to the technology of a modern digital multimeter, the microprocessor of MC3000 measures the actual battery current (in series) and the actual battery voltage (in parallel) directly at the battery in order to control and regulate the discharge or charge process. During the manufacturing process every MC3000 production unit gets tested and calibrated to 2 decimals in an expeditious process observing highest factory standards.
FIRMWARE UPDATE PC LINK The visualization of data helps with the understanding of battery performance or the details of charging algorithms. The free PC Link software offers convenient operation and overview of the charger from a Windows computer; it may also be needed for downloading and installing the latest firmware updates.
BLUETOOTH APP BLUETOOTH APP The Bluetooth 4.0 connectivity allows the user to remote control and monitor the MC3000 comfortably through an app on a portable device such as smartphone, iPad, or iPhone. The iOS app can be downloaded from iTunes Store, the Android app from Google Play Store. Operation of the app is self-explanatory and the same on iOS and on Android. Explicit pairing is not required; after download and installation just activate Bluetooth on your mobile device and launch the app.
ERROR MESSAGE BLUETOOTH APP 3. Press ‘Details’ on the screen to view graphs and slot operation details, such as Battery Voltage, Current, Temperature, Resistance etc., in a single overview. The battery icon is for switching the view between slots. Revo Revo 15:53 Details Back 4.26 4.26 4.12 4.12 3.68 3.68 3.84 2 AA 1 V 4.40 AA 4 AA AA 3 AA AA 2 V 4.40 3 4 3.84 3.70 3.70 T Mode: Status: Capacity: Temp: LiIon Charge 28 mAh 28℃ Time: Voltage: Current: Bat.Res.: 00:01:54 4.
GLOSSARY FAQ’ S 1) When I discharge 4 fully charged 18650 Li-Ion batteries at 1A/slot together at the same time, the plastic radiator grille gets hot, the metal (+) contacts too, but less so when I discharge a single Li-Ion battery at 2A. What's wrong with me? - Nothing. All is good. But if you don't feel comfortable with the high temperatures at full load, how about discharging two batteries instead? You will be surprised how not hot the externals get at reduced loads.
SPECIFICATIONS PACKAGE CONTENTS Input Power DC 12V ~ 18V / 60W PSU adapter output specs Beep Sound Range 2 octaves Circuit Power max. Charge power 50W |x|=x, for x>0 Temperature Sensors 2 for inner, 4 for outer measurements electronics vs. battery slots max.
CONFORMITY DECLARATION LIABILITY EXCLUSION & WARRANTY AND SERVICE SKYRC MC3000 satisfies all relevant and mandatory CE directives and FCC SubPart C Intentional Radiators section 15.247 The product has been tested to meet the following technical standards: Liability Exclusion EN 300328 Wideband transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques article 3.
