Function Dscription z Button set timer & cancel timer function aft Dr On/Off button for Manual mode AUX1 button Use this key to enter into & set Program mode AUX2 button Thermo mode A long push (5 seconds) of A1 & A2 buttons at the same time will start the Initial Set-up. At this time, a separate push for A1 &A2 buttons does not light any operations on the LCD. A short push of P button will enter into PROGRAM mode. A long push (5 seconds) of P button will enter into the setting for PROGRAM mode.
z LCD icon: thermo Timer Manual ON Program Set temperature Battery low Flame UP FLAME aft Dr Thermostat Thermostat NOT Flame down AUX1 CP:Chil d Proof AUX2 Pacific energy company icon Program mode setting and display area Set Temperature: This will ONLY appear when the THERMOSTAT is activated - Timer: Timer Mode will appear and activate the Timer.
Notes: aft Dr The range for the room temperature readout is 32-99 degree F. The room temperature always displays on the LCD. The range for set temperature is 45- 99 90degree F. The High Limit temperature for PROGRAM mode is 90 degree F. This High Limit termperature can not be changed by the users and Will only activate under PROGRAM mode. There is no High Limit temp for MANUAL & THERMO modes.
The FLAME icon will be ON all the time the flame in the fireplace is ON, whether it is under Manual ON, TIMER, THERMOSTAT or PROGRAM modes. The UP arrow will appear on the LCD when the motor drive is to be moving into the higher flame picture. Once the activation of the flame height is stopped, the UP icon on the LCD will disappear. The DOWN arrow will appear on the LCD when the motor drive is to be moving into the Lower flame picture.
Manual Mode: Push ON: The “man＂( for manual ON, OFF. ) ICON will appear And the FLAME icon will appear too. OFF: The man ( ) ICON will disappear and The FLAME icon will disappear too. aft Dr .Flame modulation: The flame can only be modulated when the system is ON. The flame can be ON from the Manual, Timer, Thermostat and Program modes. The FLAME icon should be on all the time the flame in the fireplace is ON, whether It is operated in Manual, Timer, Thermostat or Program modes.
.Timer function: Once this is selected, the timer ( ) icon will be on the screen and the clock will flash “30＂minutes as the start point. But the users still can go down to 10 minutes and up to 180 minutes. The 10-minute segments remains unchanged. By pushing (TIMER) button, You can set TIMER or cancel TIMER function. aft Dr You use (DOWN) or (UP) button to set your desired TIMER. 9 The range of TIMER is from 10 minutes to three hours or 180 minutes, in 10 minute segments.
.Thermo mode: Selection of (THERMO) button will light the temperature ICON and will light the smaller set of numbers ( ) aft Dr The SET area should flash to 5 seconds and during this period of time the UP and Down arrows will operated the Set Temperature to the correct setting. Once the correct temperature is obtained, the temperature will continue to flash for 5 seconds and then it will stop flashing (This means the SET process is completed.
. Program mode: (PROGRAM) button will select/operate the A short push of PROGRAM mode. A long push (push & hold for more than 5 seconds) aft Dr of button will enter into the Setting of PROGRAM mode.
next setting. & Then use ON＂. & will flash. or to change the setting of “P2 Then, use OK button to enter into next setting. & & will flash. aft Dr Then use or to change the setting of “P2 OFF＂. Then, push OK button to enter into next setting. SS & & You can use on the LCD will flash. or to change the setting of “P1 OFF＂. Then, push OK button to enter into next setting. SS & & You can use on the LCD will flash. or to change the setting of “P1 OFF＂.
*This feature is to be activated/de-activated by push TIMER/THERMO keys at the Same time for more than 5 seconds.. *When this feature is activated, the LOCK icon will appear for 5 seconds and then disappear. This LOCK icon will appear for 5 seconds again and then disappear if any of the buttons of the TX is pushed. This tells the users that the TX is LOCKED. aft Dr FCC Notice This device complies with part 15 of the FCC Rules.
