User's Manual

ManualsBrandsSkytech II ManualsElectronicsTransmiter

FUNCTIONAL SPECIFICATION

VCS-ECOTSS01

EcoFlow Touch-Screen Transmitter

Revision History

Rev. 0: Draft Release. M.R. 12/11/2012.

Rev. 1: Clarified transmission delay when cycling to THERMOSTAT mode. M. Rogers 12/12/2012.

Rev. 2: Modified transmission delay to include all modes instead of THERMOSTAT mode only. M.

Rogers 12/13/2012.

Rev. 3: Changed transmission delay from 3-seconds to 2-seconds. M. Rogers 12/12/2012

Rev. 4: Changed transmission frequency from 433.92MHz to 303.0MHz. M.R. 12/17/2012.

Rev. 5: Changed reaction to 1

touch of LCD screen (will only illuminate backlight – no reaction to

associated Zone function). M.R. 12/21/2012.

Rev. 6: Changed reaction to 1

press of push-buttons (will only illuminate backlight – no reaction to

associated button function). M.R. 2/7/2013.

Rev. 7: Changed Room Temperature Limit feature to operate in ALL modes of operation (including OFF

modes). M.R. 3/21/2014.

Rev. 8: Added LCD display flashing sequence during Main Burner ON and Cont. Pilot ignition sequences.

Reference SKCN16-019. M.R. 10/19/2016

Summary of content (10 pages)

PAGE 1
FUNCTIONAL SPECIFICATION VCS-ECOTSS01 EcoFlow Touch-Screen Transmitter Revision History Rev. 0: Draft Release. M.R. 12/11/2012. Rev. 1: Clarified transmission delay when cycling to THERMOSTAT mode. M. Rogers 12/12/2012. Rev. 2: Modified transmission delay to include all modes instead of THERMOSTAT mode only. M. Rogers 12/13/2012. Rev. 3: Changed transmission delay from 3-seconds to 2-seconds. M. Rogers 12/12/2012 Rev. 4: Changed transmission frequency from 433.92MHz to 303.0MHz. M.R. 12/17/2012. Rev.
PAGE 2
Objective Define basic construction, touch-screen LCD & button layout, and operational parameters for a wireless transmitter to operate the Copreci Valve IPI control module. Basic Construction • Transmitter body should be the same construction as model series AF-4000TSS##. • Touch-Screen LCD and three push buttons will allow input from users - the 1st touch of the LCD screen or press of a push button will only illuminate the backlight (will not respond to associated function).
PAGE 3
Functional Description Note: All function adjustments will be automatically accepted 15-seconds after pressing a given touch zone or button. The user may press the MODE/SET button to immediately accept the adjustment manually. Day and Time Display • The current day of week and time of day will be continuously displayed in the TIME/PROG Zone (except during Setup operations).
PAGE 4
o o o o o o SET TEMP Zone: Blank LIGHT Zone: LIGHT and light setting level is displayed FAN Zone: Blank TIME/PROG Zone: Current day indicator and current time is displayed AUX Zone: AUX and AUX setting is displayed FLAME Zone: Blank MANUAL ON Mode: • Transmits flame ON command • LCD Displays: o MODE Zone: ON will flash (~0.5 seconds on & ~0.5 seconds off) for 15-seconds, then ON will be displayed continuously.
PAGE 5
• • the operational mode is cycled out of, then back into THERMOSTAT mode or if the SET temperature is changed.
PAGE 6
Program Operation • Press the TIME/PROG Zone to activate or deactivate Program Operation. Pressing the MODE Zone or the MODE/SET Button will also deactivate Program Operation. When Program Operation is deactivated, the transmitter will return to MANUAL OFF Mode. • Program Operation will cycle fireplace ignition ON and OFF based on time settings (2 weekend periods and 2 weekday periods) and thermostat settings.
PAGE 7
display in MODE Zone) or PROGRAM and ON (ON display in MODE Zone) will flash 3-times (0.5-seconds OFF, 0.5-seconds ON) to indicate the change has been made. Flame-A (or Main) Adjustment • Transmits a flame height setting command to the control module to adjust the Flame-A height. • Available settings are 1-3 with a factory default of 3.
PAGE 8
Fan Adjustment • Transmits a fan setting command to the control module to adjust the fan output level. • Available settings are 0 (off) – 6 with a factory default setting of 3. If the user changes the fan speed during operation, the control will remember and use the adjusted setting on subsequent fan ON cycles (fan speed memory).
PAGE 9
AUX Adjustment • Transmits an AUX setting command to the control module to turn the AUX output ON or OFF. • While in any mode of operation, press the AUX Zone to enter AUX Adjustment, then press the UP or DOWN buttons to turn the AUX output ON or OFF; press the MODE/SET Button or wait for 15 seconds to accept the new setting. • LCD Display: o When adjusting the AUX output, AUX and AUX setting (ON or OFF) will flash in the AUX Zone.
PAGE 10
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.