User Manual ・
User Manual CONTENT Safety Instruction ....................................................................................................................................................... 4 Chapter 1 Features ........................................................................................................................................................... 1 Chapter 2: Overview .........................................................................................................................
User Manual 6.3.2 Playback .................................................................................................................................................. 43 6.3.3 Configuration .......................................................................................................................................... 46 6.3.4 Local setting............................................................................................................................................ 55 6.3.
User Manual Safety Instruction 1. Read Instruction All the safety and operating instruction should be read before the equipment is operated. 2. Power sources This equipment should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power, please consult your equipment dealer. 3.
Chapter 1 Features Function Brief and Description Real time monitoring Double video output; with monitor, VGA virtual output port or HDMI Output; Support net-viewer and MP live surveillance and also support zoom in/out, auto sequence and PIP display. Record H.
User Manual Chapter 2: Overview 2.1 Front Panel Reminder: DVR is the abbreviation of Digital Video Recorder Equipment. 2.1.1、4CH DVR Front Panel Item 1 Key title or Indicator Remark USB Port Function & Description Connect to USB2.0 port List 2-1 2.2 Rear Panel 2.2.
User Manual 2.2.
User Manual 2.3 4/8-CH Remote Controller Item 1 Key title 1-8 Key function Channel select 1-8; Numeric key 9、0 Numeric key; Clicking numeric “0” allow you switch to GUI (Graphical user Interface) function 3 ALL Multiple display mode 4 Menu 5 ▲ Up arrow key, Volume adjust 6 ▼ Down arrow key, Volume adjust 2 ◄/ Left/Down key, Decrease/increase control bar SEL Select key/Edit key; Confirm the selected operation.
User Manual Mouse Operation Except using buttons of front panel or remote controller, you also can use mouse to perform system operation. TYPE Function In menu lock mode, Enter into pop-up menu and clicking any sub menu to pop up Log-in window; on menu unlock mode, enter into pop-up menu, and then clicking left key to enter into any sub menu directly.
User Manual Chapter 3 DVR INSTALLATION 3.1 HDD Installation （Applicable to the model with HDD drawer） Caution： Please do not Install or take out hard drive when DVR is running! (1) The model has a HDD drawer. Please use provided key to take out the HDD drawer and put HDD into the drawer correctly.
User Manual Chapter 4: DVR Boot up 4.1 System Initialization After connecting the Power cable of DVR to wall outlet and pressing the Power button on the front panel, you will enter into the system initializing screen shown as Picture 4-1 Picture 4-1 4.2 Live Interface After finishing initialization the system will enter into screen. Picture 4-2 is the 16-split display defaulted by system, which is showing no video input status.
User Manual 5.
User Manual 5.3 Main Menu On mode, click [Menu] button on the front panel or Remote controller to enter into Main menu interface shown as Picture 5-2. And Picture 5-2 also you can click [ ] icon to enter the main menu screen. In Main Menu mode, you can control device management settings, such as Display, Record, Network, Search, Device, System and Advanced setting etc. 5.3.1 Display 5.3.1.
User Manual 5.3.1.2 Output mode Go to [Main menu Display Output] to enter into the output set interface shown as Picture 5-5. Click [Live] to pop up the interface shown as Picture 5-6. Now you could perform channel sequence setting. Picture 5-5 Picture 5-6 Click [Spot sequence] to enter into the interface shown as Picture 5-8. Click [Spot output] option and set relative parameters shown as Picture 5-7.
User Manual Picture 5-10 Picture 5-11 5.3.1.3 Privacy Zone The function Allow you setup privacy zone parameters according to Picture 5-12. Each channel could set up to four privacy zones, and please follow below steps to set: 1. Select the area no (Area 1 ~ Area 4); 2. Click [Setup] to adjust position of mask area; 3. After finishing position adjust, click right key of mouse to return back [Privacy zone] interface; 4. Click [Apply] to save the above setting. Picture 5-12 5.3.
User Manual Channel: allow you setup the channel you desired. Record: allows you set up record status (Enable/Disable) of each channel Pack Duration: indicates maximum continuous record time (15, 30, 45 and 60 min). Pre-record: Motion detection and I/O triggered record support Pre-record function. Picture 5-14 5.3.2.2 Schedule Click [Main Menu Record Schedule] to enter into the interface shown as Picture 5-15. [Channel] option allows you select one channel you desired.
User Manual 5.3.3 Search 5.3.3.1 Record Search Click [Main Menu Search Record Search] to enter into the interface shown as Picture 5-17. Channel: allows you select the channel(s) you desire to search. Date Search: In the Video Search screen, user can search for all the records in a specific date.
User Manual 5.3.3.3 Event Search Click [Main Menu Search Event Search] to enter into the interface shown as Picture 5-20. You could highlight and double-click the desired record for playback. And you also can filter the records you want to view based on date, time, and channel and record mode search. (First Page): go to the first page on the list. When you view other pages, clicking [First] button brings you back to Page one. Picture 5-20 (Previous page): go to the previous ones of current page.
User Manual Picture 5-24 After backup finished, please click [OK] button shown as Picture 5-24. Note: File will be saved as *.264 format. You could playback the record files via Dvr Client player. When installing Dvrclient, system will auto install the player. Please make sure the back-up device connect well before backup. 5.3.3.4.2 back-up file based on time Also allow you back-up record files based on time. Please follow below steps to back up these files (Details operations please refer to section 5.
User Manual ：Slow button: click the icon to play the backup record at 1/2, 1/4, 1/8 and 1/16 speed. ：FF button: click the icon to fast forward the backup record at x2, x4, x8 and/or x16 speed. ：Open: click the icon to open one record file. ：click the icon to enter into full screen mode. ：Click the icon to never place one target to top. ：Click the icon to place one target to top. ：Click the icon to place the playing record to top.
User Manual 5.3.4 Network 5.3.4.1 Network set Click [Main menu Network Network] to enter into the below interface shown as Picture 5-30. Picture 5-30 After selecting network mode - such as DHCP, PPPOE or static allocation- and setting up web ports ， you can visit DVR remotely through a network or internet. UPnP (Universal Plug and Play) function: If router supports UPnP function and set to “On”, system will automatically forward port to router. DNS: DNS server is generally provided by local ISP.
User Manual 4. Input a specified IP address to [IP address] column; 5. The Subnet Mask, gateway and DNS server should be consistent with your router’s configurations. 6. Input DNS address. Please check router firstly. The setting should be consistent with router’s 7. Click [Apply] button 8.
User Manual Video: allow you open or close the sub stream output. If you select “Enable” system will select sub-stream preview and guarantee image quality once network is unstable. Frame rate: allow you set net transmittal frame rate. User could select the relative value by pull-down menu. Bit rate: allow you set net transmittal bit rate. User Picture 5-35 could select the relative value by pull-down menu. Audio: When tick-selecting the option, system will record video and audio simultaneously. 5.3.4.
User Manual Click [Main menu Network Mobile] to enter into the [Mobile] interface shown as Picture 5-41. User Name: indicate user name of DVR, and support numbers and characters and 1~15 bits length User password: indicate user password of DVR, and also support numbers and characters and 1~15 bits length Server port: Mobile monitoring port. Setting range is between 1024 and 65535. Picture 5-38 Please note that the server port could not duplicate the port you have set to network set.
User Manual Mobile Viewer’s Access Instruction The DVR is currently compatible with mobile phones running Windows Mobile, Symbian, Iphone, Blackberry and Androids operating systems. Below are these Mobile Viewer’s installation procedures. 1. Windows Mobile ： 1) First you need to copy a program named as “Aseesetup.CAB” that is included on the CD provided by the DVR to the mobile phone.
User Manual Note: Please firstly make sure you have right PTZ parameter setting (details please refer to User Manual-Section 5.2.6.3) on DVR, then you could control PTZ camera through your mobile phone. The captured images will be saved to the defaulted path (Explorer Program Files Moveeye Photo file). If you use this program first time or need to change parameter settings, please click [Setup] button to enter into the window shown as Picture 6.
User Manual Picture 11. 6) If the program is installed into SD card, please enter into 【Application】 menu to find [Asee] icon shown as Picture 12. Picture 10 Picture 11 Picture 12 7) Click [Asee] icon to run the program, and then you will enter into the interface shown as Picture 13. (Function buttons in the bottom in turn are:） 1 CH 1；CH 2 ；CH3；CH 4 2 PTZ Direction :left, right, up, down 3 PTZ Lens control: Focus+/-, Zoom+/- and Iris+/- from left to right in turn.
User Manual 2) Run the iTunes program, and then click the Menu- [Store Search] to enter into its sub-menu. 3) On the [Search] mode, enter the characters “ASee” to search the program “ASee”. 4) Download and install the “ASee” program. 5) After finishing installation, [ASee] icon will be displayed to mobile phone interface shown as Picture 15. Picture 15 Channel select PTZ Direction ( left, right, up, down) Area Selection（ZOOM+、ZOOMFocus（focus +, focus-） ⑤ Aperture（I+,I -）,).
User Manual 4） Choose [Application Loader ] from the Main Menu shown as Picture 18 5） Click [Start] Button on the 【Add/Remove application】menu shown as Picture 19 6） Click [browser] button and tick-select [ASee.alx] file shown as Picture 20 7） Click [Finish] button to finish the installation shown as Picture 21. Picture 18 Picture 19 Picture 20 Setup and operation on the Blackberry phone viewer Picture 21 1） The Blackberry viewer will be installed to the [Downloads] directory shown as Picture 22.
User Manual 4） Enter the Monitor DVR info in the below Setup Menu； Picture 25 Picture 26 4.1 Select the Network Type supported by Blackberry phone. Picture 27 4.2 Click [Save] button to save the above setting, and system will return back to Live display. 4.3 Click the [History] button to enter into the History List shown as Picture 28. 4.4 Highlight one record and click [Enter] button to enter into pop up menu.
User Manual 4.5 When selecting [Edit] option, system will allow you edit the history record. Picture 29 will be deleted. 4.6 When selecting [Delete] option, the history record Picture 31 Picture 30 5) Click [Next Page] icon to search [Channel] option shown as Picture 32 and Picture 33, and then choose the channel you want to display. Picture 32 Picture 33 6) Click [Full screen] icon to enter into full screen display mode, again click the [Trackball] button of mobile to quit the full screen mode.
User Manual 9) Click [Close] button to exit the program shown as Picture 35. 5. Androids Mobile Please make sure the software environment support on your Android Mobile, such as Apkinstaller. 1. Make sure your mobile have been connected to network and could download the software. Picture 36 Picture 37 Picture 38 Picture 38 2. Enter into [Program] option and highlight [E-market] icon shown as Picture 37. 3. Enter into the [E-market] interface shown as Picture 38. 4.
User Manual 6. 7. 8. 9. 10. Enter into [Program] file and click [Apkinstaller] icon shown as Picture 44 Find the ASee.apk file you want to install shown as Picture 45 Click the software to install to your phone shown as Picture 46 and Picture 47. Enter into [Program] option to click [ASee] icon shown as Picture 48. Enter into [ASee] main interface shown as Picture 49.
User Manual 5.3.4.6 DDNS Set DDNS (Dynamic DNS) is a service that register a domain name and the floating IP address with the DDNS server so that the domain name can be routed to the IP address even if the IP address is changed in a dynamic IP system. User can visit a remote DVR by using DDNS on above three types (Static, DHCP and PPPoE) You can apply for a DDNS account for free at the web www.3322.org or www.dyndns.org. You can register on DVR2009.3322.org or dyndns.
User Manual Show Message: You can set show message on the screen when motion alarm is detected. Buzzer time: you can set how long the buzzer will sound when motion is detected (10s, 20, 40s, 60s); Send Email：Allows you set the alarm images is issued to a specified email. Full screen Alarm: The function is defaulted to “On". When the motion is detected, the corresponding channel will be switched to the full screen mode. Record Channel: the record channel will be activated when the object move is detected.
User Manual Record Channel: allow you select channels you want to record. Post Recording: you can set how long alarm record will last when alarm ends (30s, 1minute，2minute，5minute); Copy: allow you copy all the setting of one channel to other ones. Alarm Type Function Sends alarm when DVR can’t receive video signal (such as camera damage, cable broken or Video Loss damaged or power supply malfunction). Motion When an object moves into motion detection area, alarm will be triggered.
User Manual Total Space – Total size of the hard drive currently installed. Free Space – Total amount of free space available on the hard drive currently installed. Useable Rec. Time – Free space currently available in hours. Auto-overwrite – When set to ENABLE the DVR will record over the oldest files on the hard drive.
User Manual Picture 5-46 When operate DVR via keyboard, it is required to set communication protocol. Baud rate: set baud rate of serial communication. Data bit: set data bit of serial communication. Stop bit: set stop bit. Parity Check: set parity check to or other. 5.3.7 System 5.3.7.1 General Click [Main Menu System General] to enter into the interface shown as Picture 5-47 You will be allowed to modify system date, time, date/time format, language, video format and auto logout.
User Manual Picture 5-50 NTP Service：Allow you enable/disable the NTP function. Server Address: currently support three servers, including time.windows.com, time.nist.gov and pool.ntp.org. Time Zone: System supports thirty Time Zones. Update now: Click [Update Now] button to change the above NTP set. Note: The above change will be available only when system connected to internet. And When NTP function is set to “Enable”, system will calibrate the time at every 00:07:50 and every start-up. 5.3.7.
User Manual Manual record: allow you manually start/stop record. Backup: Tick-select the option, the user is allowed to backup the record of all the channels. Live: Tick-select the option and the user is allowed to view all the live images for all the channels. Playback: Tick-select the option and the user is allowed to playback the record you selected. PTZ control: Tick-select the option and the user is allowed to perform the PTZ operation for the selected channel. 5.3.7.
User Manual 5.3.8.2 Event Click [Main menu Advanced Event] to enter into the interface shown as Picture 5-57 Event Type: support the three abnormal types: Disk No Space, Disk Error and Video Loss. Enable: allow you activate abnormal alarm. Alarm out: select [Enable] or [Disable] Latch time: you can set how long the buzzer will sound when external sensor alarm is detected (10s, 20, 40s, 60s); Show Message: You can set show message on the screen when sensor alarm is detected.
User Manual Picture 5-59 We introduced setting PTZ parameters previously in section 5.3.6.2 – PTZ Set. Here we will discuss how to operate PTZ controls. Click the [ ] icon to enter into [PTZ control] menu shown as Picture5-60. Now user can control the camera with Pan, Tilt and Zoom capabilities. Click [Zoom-/+] button to zoom in / out the image; Click [Focus -/+] button to focus the image; Click [Iris -/+] button adjust iris to open or close.
User Manual 5.9 Mute Click the [ ] icon, or press button on the front panel and Remote controller to control the mute of DVR. 5.10 Manual Record You can start manual record function, or you also can click [ ] button on the Front panel or Remote controller to activate manual record. Please stop record manually once you activate manual record. 5.11 Stop record To stop record quickly, please click the icon [ remote controller. ] or [Stop] button on the front panel or 5.
User Manual Chapter 6: Web Application Manager 6.1 Plug-in download and installation Open your web browser and input the IP address and web port of DVR, such as： http://172.18.6.202:8080/ . If your computer is connected to internet, it will download and install “ActiveX” Plug-in automatically. If your computer system is Vista, you may need to setup the user authority. Details please refer to the below picture: Start →setup→ control panel （Tick “√” use UAC to help protect your computer and confirm OK）.
User Manual Picture 6-1 6.2 Web Application Manager Log-in After plug-ins installation, please input user name, password and client port; and select or , and then allow you tick-select ; Now you click [Log-in] button, and then you are allowed to access a remote DVR and monitor live video images using Web browser anytime from virtually anywhere. Noted that defaulted password is empty.
User Manual ：Volume switch ：Record icon: record will be saved to a specified position after starting record. ：Snapshot function: allow you capture the live images and save it to a specified position. The image should be saved as *.bmp format. : clicking the icon will close/open the current channel’s live mode Or click the right key of mouse on each window to pop up the interface shown as Picture 6-4. Show bit rate: show current bit rate; Original Proportions: show original proportions.
User Manual 6.3.1.3 Video control ：Adjust video Hue; ：Adjust video brightness; ：Adjust video Contrast; ：Adjust video saturation; ：Recover ex-factory default value. Picture 6-6 6.3.2 Playback Click [ ] icon to enter into interface shown Picture 6-7. Picture 6-7 The Web Application Manager supports up to 4 channels playback simultaneously. 6.3.2.
User Manual Picture 6-8 Secondly, select record type (Normal record, Alarm record and All) and then click < > button shown as Picture 6-9. On the time axis, red part stand for alarm record, yellow stand for normal record and original part stand for no record during this period. Picture 6-9 > option, that means the selected channel will playback If you tick-select < synchronously; otherwise, you could separately control the channels playback. Thirdly, Click [ ] icon to start record playback.
User Manual Detail brief description is shown as below list Key Description Key Play Description Open/close audio Pause Volume adjust Stop Playback control bar (x1/2,1/4,1/8, normal, x2, x4, x8) By frame Stop all the play Clip Single channel mode Capture Quad mode Download Full screen Open all the channels Stop all the channels Record file clip After opening playback, click [ ] icon to clip the selected file; and click again to stop the clip function. Record clip file will be saved as *.
User Manual Picture 6-12 Tick-select the record file you want to download and click [Start download] System will download the record file in turn and save to local PC. 6.3.3 Configuration Click [Configuration] option to enter into the [Config] interface shown as Picture 6-13 and allow you set Display configuration, Record, Network, Alarm, Device, System parameters and Advance according to your actual request. 6.3.3.
User Manual Picture 6-14 6.3.3.2 Record Click option to unfold its sub-options: Record parameter, Schedule and Main stream. 1、 Record Parameters: Under [Record parameters] option, allow you set channel, record enable, pack time and Pre-record status shown as Picture 6-1 Picture 6-15 2、 Schedule: Detailed parameters please refer to DVR local setting. Green stand for Normal record; Yellow stands for Motion detection; Red stands for I/O triggered record.
User Manual Picture 6-17 This figure is only for D9016 / CIF model reference 6.3.3.3 Network Parameters Unfold option to enter into its sub-options: Network, sub stream, Email, mobile and DDNS configuration. 1、 The model support three network type, including Static, DHCP and PPPoE Static: System default as its network type. User could allocate IP and perform Port forwarding for DVR according to different router. When set to “On”, user no needs to perform port forwarding.
User Manual Set network type to “PPPoE” shown as Picture 6-20. consistent with DVR local setting. Its user name and password should be Picture 6-20 2、 Sub stream (shown as Picture 6-21): Relative parameters should be consistent with DVR local setting. Picture 6-21 3、 Email setting: Click [Email setting] option to allow you set alarm email configuration parameters shown as Picture 6-22. Detailed parameters should be consistent with DVR local setting.
User Manual 4、 Mobile: Its user name, password and port No should be consistent with DVR local setting shown as Picture 5-23. Picture 6-23 5、 DDNS Setting: After user applies for DDNS service shown as Picture 6-24, you could enable function under any one network type mode (Static, DHCP and PPPoE). Now you remotely visit the DVR through domain name (http://domain name: port No). Details setting should be consistent with DVR local setting. Picture 6-24 6.3.3.
User Manual Picture 6-25 1、 Motion Detection: allow you configure its , , and etc. Details setting should be consistent with DVR local setting (Shown as Picture 6-26). Picture 6-26 2、 I/O Alarm: allow you configure , , and etc. Details setting should be consistent with DVR local setting (Shown as Picture 6-27). Picture 6-27 6.3.3.
User Manual Picture 6-28 2、 PTZ Configuration (shown as Picture 6-29): details setting should be consistent with DVR local setting. Picture 6-29 6.3.3. 6 System Click option to unfold its sub-options: General, Users and information. 1、 General: User could check DVR’s language and video system, and also set system time, date format, DST and NTP shown as Picture 6-30. Details setting should be consistent with DVR local setting.
User Manual 2、 Users: Allow you configure user name and password shown as Picture 6-31. Details setting should be consistent with DVR local setting. Picture 6-31 3、 Information: Allow you check out device name, number, type, MAC address, software version, IE version and hardware version shown as Picture 6-32. Picture 6-32 6.3.3. 7 Advanced Click to unfold its sub-options: System update, Load default, Events and system maintain etc.
User Manual Please follow below steps to upgrade the system: a. Select the upgrade file’s path shown as Picture 6-34. Please note that the format of upgrade file is *.sw. Picture 6-34 b. Click , now processing bar will display current upgrade status shown as Picture 6-35. Picture 6-35 2、 Load Default: allow you recover defaulted parameters of DVR remotely shown as Picture 6-36. Details setting should be consistent with DVR local setting.
User Manual 3、 Events: allow you configure abnormal type, buzzer output time, and alarm email and show message shown as Picture 6-37. Details setting should be consistent with DVR local setting. Picture 6-37 4、 Maintain: allow you set auto system maintain for DVR remotely shown as Picture 6-38. Detail setting should be consistent with DVR local setting. Picture 6-38 6.3.
User Manual Chapter 7: Appendix 7.1 Operation Function Table Type Title Set system date/time, display format and day-light saving time 26 Language select Set system language 27 Record search Time based search, channel based search and rec. mode based search.
User Manual Menu button Enter Clicking the button will save current parameter. Default Recovery Clicking the button will recover current parameters to system defaulted value. after clicking [Enter] button ESC Clicking the button will exit the current menu. ○,1Time setting Adjust system time 26 Format HDD 15 Set network type and web port (except of 10 ○,2HDD Manage ○,3Net setting Basic application Guide The option will be effective PPPoE, other type need forward web port to router of DVR.
User Manual www.qq.com @qq.com smtp.qq.com pop.qq.com smtp.163vip.net popx.163vip.net @sina.com.cn smtp.sina.com.cn pop3.sina.com.cn @yahoo.com.cn smtp.mail.yahoo.com.cn pop.mail.yahoo.com.cn @yahoo.com smtp.mail.yahoo.com pop.mail.yahoo.com google.com @gmail.com smtp.gmail.com(465/587) pop.gmail.com(995) www.china.com @china.com smtp.china.com pop.china.com www.sohu.com @sohu.com smtp.sohu.com pop.sohu.com smtp.163.net pop.163.net smtp.163vip.net pop.163vip.net 163.net www.
User Manual A: Check if the battery is power off; or check if the Remote Controller is broken. 8. Q: Can we records whilst playing-back? A: Yeah, you can do it. The system support you records whilst playing-back. 9. Q: Can we erase some recorded file from DVR. A: Considering the safety factor, you can’t delete the recorded file directly from the device. When you actually erase all the recorded files, please select HDD format function 10.
User Manual 8-CH 7.
User Manual The material in this document is the intellectual property of our department . No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without our department prior written permission. Our products are under continual improvement and we reserve the right to make changes without noti ce. But no guarantee is given as to the correctness of its contents. We do not undertake any responsibility for the harms cause by using our product.
