Operation Instruction

ManualsBrandsSkyworth ManualsElectronicsWIFI Module

Shenzhen skyworth RGB electronic co., LTD.

Model: NTUD-U8

Respect of customer, sincerely thank you for purchasing

SKYWORTH equipped with wireless WIFI NTUD-U8 type USB

peripheral products.

This product can support USB2.0 protocol, based on the

IEEE802.11 b/g/n and BT5.0 standard design. With all the way

to send and receive all the way (2T2R) dual channel work,

maximum transmission rate of up to 300 Mbps. Ensure that

users browse and download data flow, security and stability.

NTUD – U8 wireless WIFI USB peripheral product support

Windows XP/Vista / 7 / Linux operating system. In SKYWORTH

TV, have complete embedded in the product and the driver,

without user to install, and at the same time support Linux and

Android.

Used in TV production operation is as follows:

1. Turn on the TV, switch to the "home page" interface.

2. Select "Settings" feature. "OK" to enter

3. Select "network setup" function. "OK" to enter;

4. Choose the "wireless network", "OK" to enter;

Summary of content (7 pages)

PAGE 1
Shenzhen skyworth RGB electronic co., LTD. Model: NTUD-U8 Operation Instruction Respect of customer, sincerely thank you for purchasing SKYWORTH equipped with wireless WIFI NTUD-U8 type USB peripheral products. This product can support USB2.0 protocol, based on the IEEE802.11 b/g/n and BT5.0 standard design. With all the way to send and receive all the way (2T2R) dual channel work, maximum transmission rate of up to 300 Mbps. Ensure that users browse and download data flow, security and stability.
PAGE 2
5. According to the needs, select "auto search", "manual connection", etc. Press the "OK" to enter 6. Choose their own after the AP name "OK" to enter, Enter the password. Television system has the memory function, for the first time to use should be according to the above steps, later need not operation, boot automatically connected. If need to change the AP or change the mode of connection, need according to the above steps again.
PAGE 3
to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/television technician for help.
PAGE 4
(5) RF exposure considerations: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This compliance to FCC radiation exposure limits for an uncontrolled environment, and minimum of 20cm separation between antenna and body. The host product shall show the same or similar statement to the end users.
PAGE 5
(8) Information on test modes and additional testing requirements. Information on test modes: The host manufacturer can use the software “SecureCRT” for access to the test modes. Connected to the computer through the serial port of the host product and enter the command as following. if it does not work, then the host product manufacturer should coordinate with the module manufacturer for access to test mode software. Bluetooth: cd data Signaling mode： ./boots_srv & ./boots -c reset .
PAGE 6
11 b 11M ./wifitest -t 0 -c 1 -R 6 -B 0 -s 1 -i 30 -S 0 -n 0 -p 15 -y 2 -Y 0 11g 6M ./wifitest -t 0 -c 1 -R 4 -B 0 -s 60 -i 30 -S 0 -n 0 -p 18.5 -y 3 -Y 0 11g 54M ./wifitest -t 0 -c 1 -R 12 -B 0 -s 60 -i 30 -S 0 -n 0 -p 18.5 -y 3 -Y 0 11N 20M MCS0 ./wifitest -t 1 -c 1 -N 0 -B 0 -s 1 -g 0 -i 30 -S 0 -n 0 -p 17 -y 3 -Y 0 //-N 0-7 MCS0-MCS7 11N 40M MCS7 ./wifitest -t 1 -c 3 -N 7 -B 1 -s 1 -g 0 -i 30 -S 0 -n 0 -p 17 -y 3 -Y 1 //-N 0-7 MCS0-MCS7 Related command instructions are as follows: .
PAGE 7
c) If the investigation indicates a compliance concern the host product manufacturer is obligated to mitigate the issue. Host products using a modular transmitter are subject to all the applicable individual technical rules as well as to the general conditions of operation in Sections 15.5, 15.15, and 15.29 to not cause interference. The operator of the host product will be obligated to stop operating the device until the interference has been corrected.