Product Brochure

ORDERING DATA
No. 30-75 COMPLETE BASEBOARD
PACKAGE
Contains heating element and
enclosure. Following items included:
expansion cradles, support brackets,
damper vane, 2" wide splice plate
with 5' lengths and longer.
LENGTHS: 2', 3', 3
1
/2', 4', 5', 6', 7', 8',
10', 12'
No. 30-DW ENCLOSURE ONLY
PACKAGE
All parts and lengths as
No. 30-75 WITHOUT heating element
or expansion cradles.
No. E-75
3
/4" ELEMENT ONLY
PACKAGE
Heating element with expansion
cradles; NO enclosure.
LENGTHS: 2', 3', 3
1
/2', 4', 5', 6', 7', 8'
PACKAGING
Each baseboard or enclosure only unit
is individually packed—completely
assembled—in its own Zip-strip carton,
with end flaps clearly marked and
color-coded. See R-01 price list for
packaging of accessories.
HEATING ELEMENT SPECIFICATIONS:
Furnish and install E-75 baseboard heating
element as manufactured by Slant/Fin, con-
sisting of
3
⁄4" nominal copper tubing, with 2
5
⁄8"
x 2
1
⁄8" x .009" aluminum fins, bent to 2
5
⁄16" x
2
1
⁄8", spaced 55 per linear foot. A flange with
four teeth shall be formed on each fin to
increase thermal contact and to space and
lock the fins uniformly in place. One end of
each element tube shall be expanded to
receive the unexpanded end of another,
without couplings.
HOT WATER RATINGS
Fine/Line 30 – No. 30-75 baseboard with 3/4" E-75 element.
BTU/hr./ft. with 65˚ entering air † Millinches per foot. *Ratings at 140˚F and lower temperatures determined by mul-
tiplying 150˚F rating by the applicable factor specified in testing and rating standard for baseboard radiation.
NOTE: Ratings are for element installed as per drawing shown here, with damper open, with expansion cradles.
Ratings are based on active finned length (5" to 6" less than overall length) and include 15% heating effect factor.
Use 4 gpm ratings only when flow is known to be equal to or greater than 4 gpm; otherwise 1 gpm ratings must
be used.
260 North Elm Street Westfield, MA 01085
BRACKETS PER LENGTH
Complete assembly and enclosure only
COVER ASSEMBLY SPECIFICATIONS: Furnish and install Fine/Line 30-75 baseboard cover
assembly as manufactured by Slant/Fin. The cover consists of a one-piece bottom, back and
top panel, one-piece front panel and one piece damper vane that are formed out of galvanized
cold rolled steel. Cold rolled steel that is not galvanized is not acceptable. The galvanized steel
makes the cover rust resistant. Bottom and top of back panel shall have channels along entire
length to receive full-height support brackets. Brackets shall add support to the top of the rear
panel. The factory installed damper vane shall modulate fully and freely, while retaining any
setting through its arc. Damper shall swing in position on damper pivots inserted in die-formed
slots towards top of support bracket. Roll formed pivot point is not acceptable. All cover com-
ponents shall be painted in a Nu-White, thermosetting polyester enamel.
Brackets shall be die-formed of rephosphorized cold rolled steel, for rigid bracing and spring
locking. Each length of baseboard shall have a minimum quantity of factory installed brackets
per length of baseboard cover as follows: 2, 3 and 3
1
⁄2' have 2 brackets; 4 and 5' have 3 brack-
ets; 6, 7 and 8' have 4 brackets; 10' has 6 brackets; 12 and 14' have 8 brackets. Fewer brack-
ets are not acceptable.
Slide-action polypropylene expansion cradles shall protect element bottom and sides from
contact with support brackets and cover, allowing free lateral element expansion for noiseless
operation. Cradles shall be installed on heating elements at location of brackets.
END CAP Left End Cap
3
3
⁄4" wide, No. 30-LEC
with piano-hinged Right end cap
front panel, closed No. 30-REC
end. For use at
doorways.
SLOTTED END CAP Left End Cap
3
3
⁄4" wide, No. 30-LEC-SLOT
with piano-hinged Right End Cap
front panel, slotted No. 30-REC-SLOT
end. For use at wall
partitions.
INSIDE CORNER 90˚ inside corner
3
3
⁄4" wide No. 30-IC-90
at top, with piano- 135˚ inside corner
hinged, contoured No. 30-IC-135
front panel. 91˚to 179˚field
adaptable inside
corner No. IC-FA
VALVE COVER Left valve cover
8" wide, No. 30-LVC
with extra wide Right valve cover
piano-hinged front No. 30-RVC
panel, closed end. Center valve cover
(30-CVC has open No. 30-CVC
ends.)
FILLER SLEEVE (4 piece set)
Cover gaps from 7" filler sleeve
1" to 6" or No. 30-FS-7
1" to 12"
Includes back, 14" filler sleeve
top and front panels No. 30-FS-14
and damper vane.
OUTSIDE 90˚outside corner
CORNER No. 30-OC-90
One-piece unit without 135˚ outside corner
hinged panels. No. 30-OC-135
SOLID WALL TRIM
/SPLICE PLATE 2" solid
2" or 4" solid No. 30-WT-2
(non-hinged), with open
ends. For use at left or
right wall partitions or 4" solid
as one-piece filler sleeve. No. 30-WT-4
Fine/Line 30 Hinged Accessories
WATER
FLOW
PRESSURE
DROP
†
110˚F 120˚F 130˚F 140˚F 150˚F 160˚F 170˚F 180˚F 190˚F 200˚F 210˚F 215˚F 220˚F
1 GPM 47 160* 210* 260* 320* 380 450 510 580 640 710 770 810 840
4 GPM 525 160* 220* 270* 340* 400 480 540 610 680 750 810 860 890
Length, ft. 2 - 3.5 4 - 5 6 - 8 10 12 - 14
Brackets 2 3 4 6 8
Touch-Up Paint
4.5 oz touch up paint
- spray can
Touch-Up Paint
6 oz touch up paint
- mini bottle w/brush