Submittal Sheet

ManualsBrandsSlant/Fin ManualsBaseboard Heaters8 ft. Multi/Pak 83A Baseboard

50 Series

Furnish and install 350 Series Model___________

aseboard cover assembly as manufactured by

lant/Fin Corporation, consisting of one-piece bottom,

ack and top panel, and one-piece 19 (16) gauge front

panel, formed of cold rolled steel. Bottom and top

dges of back panel shall be formed to provide chan-

els along entire length, to receive full-height support

brackets.

Brackets shall be die formed of electro-galvanized

old rolled steel, for rigid bracing and spring locking.

lide-action expansion cradles, formed of polypropy-

ene, shall be inserted between heating element and

support bracket. Cradles shall protect element bottom

nd sides from contact with brackets or cover, confining

lement to free lateral expansion for noiseless opera-

ion.

Provide all required accessories for a complete

nstallation. Cover accessories shall be telescopic and

hall match enclosure color.

ll cover components shall be painted in Nu-White,

oven baked melamine cross-linked polyester enamel.

D Series

urnish and install as shown on the plans HD

Series—slope-top baseboard with element, required

mounting components and accessories as manufac-

ured by Slant/Fin Corporation. Complete two-piece

nclosure assembly shall consist of full back panel with

interlocking slope top front panel, factory packaged with

necessary brackets.

ront cover shall be fabricated from 16-gauge steel,

ack panel from 20-gauge steel. The front panel &

accessories shall be finished in galvanized finish or as

ustom color matched as per specifications. Fin-tube

element(s) shall be Model___________. Provide

engths, heights and capacities as scheduled on plans.

racket with element guide shall be spot welded to

back panel every 12 inches. There shall be dimpled

anchoring holes every 12 inches on front cover. Use 8 x

⁄8" self-tapping screws with countersunk heads to fasten

front cover to brackets. Screws recess into dimpled

anchoring holes on front cover. Screws are supplied in

carton with cover.

Provide all required accessories for a complete

installation. Cover accessories shall be telescopic to

eliminate the need to perfectly butt one length of cover

to the next. Accessories to be fastened with screws

(pan-head) supplied by others.

Multi/Pak 80

Furnish and install Multi/Pak

80 baseboard

cover assembly as manufactured by Slant/Fin

Corporation, consisting of one-piece 21-gauge back

and top panel, and one-piece 18-gauge front panel,

formed of cold rolled steel. Bottom and top edges of

back panel shall be formed to provide channels along

entire length, to receive full-height support brackets.

Brackets shall be die formed of zinc-bonded 16-

gauge quarter-hard cold rolled steel, for rigid bracing

and spr

ing locking. Slide-action expansion cradles,

ormed of polyprop

ylene, shall be inserted between

heating element and suppor

t brack

et.

adles shall pro-

tect element bottom and sides from contact with brack-

ets or cover, confining element to free lateral expansion

or noiseless oper

ation. Room-control damper vane, of

quarter-hard cold rolled steel, shall be provided for each

length of enclosure, and shall modulate fully and freely,

yet retain any setting through its arc without protruding

knobs or other devices. Support bracket shall be formed

to retain and suppor

t damper v

ane without use of addi

tional piv

ots

All co

er components shall be painted in

Nu-White, oven baked melamine cross-linked polyester

enamel.

Base/Line 70

Furnish and install Base/Line 70 baseboard cover

assemb

ly as man

actured b

y Slant/Fin Cor

., consist

ing of back panel, front panel, damper vane and sup-

port brackets (electro-galvanized), formed of cold rolled

steel. Bottom and top edges of bac

k panel shall be

formed to provide channels along entire length to

eceive full-height support brackets. The support brack-

ts shall be formed to accommodate return tubing

bove the heating element using standard fittings.

Damper vane shall modulate fully and retain any setting

hrough it’s arc. All cover components shall be painted

n Nu-White thermosetting polyester enamel.

& EM Series

urnish and install as shown on the plans “F”

r “EM” Series flat-top enclosures with elements,

required mounting components and all accessories as

anufactured by Slant/Fin Corporation. Cover shall be

f one piece construction. Enclosure shall be EM-5,

M-12, EM-19, F-5, F-12 or F-19 and shall have (1,2 or

3) tier element. EM enclosure shall be made of expand-

d steel. F enclosure shall consist of stamped top grille

ith pencil-proof air discharge louvers.

overs shall be fabricated from 18-gauge (16-

gauge for EM) steel in electro galvanized finish or as

custom color matched as per specification.

rackets and hangers shall be channeled

teel in electro galvanized finish. Fin-tube element(s)

shall be Model_________. Provide lengths and capaci-

tiies as scheduled on plans.

urnish required channeled bracket-hanger

ssemblies for rigid element support.

Provide all required accessories for complete

installation. Enclosure accessories in bonded zinc steel

hall be telescopic and match enclosure color.

C-540, C-440 and C-340 Element

Furnish and install C-540, C-440 and C-340

fin-tube heating elements as manufactured by

lant/Fin Corporation, consisting of 1

⁄4"

nominal* cop-

per seamless-drawn tubing* with 4

⁄4" x 4

⁄4"x .020" alu-

inum fins spaced 40 per linear foot. Fins shall be

echanically bonded to the tubing to increase thermal

contact and to space and lock the fins uniformly in

place. A flange with four teeth shall be formed on each

fin to increase thermal contact and to space and lock

the fins uniformly in place. One end of each element

shall be expanded to receive the expanded end of

another, without couplings.

* C-440 is 1" copper pipe. C-340 is

⁄4" copper pipe.

S-540, S-532 and S-832 Element

Furnish and install S-540 and S-532 fin-tube

heating element as manufactured by Slant/Fin

Corporation, consisting of 1

⁄4" IPS steel pipe*

(Schedule 40), with 4

⁄4" x 4

⁄4"x .024"steel fins spaced

40 per linear foot for S-540 and 32 per linear foot for S-

532 and S-832. The pipe shall be forced through under-

sized fin holes to obtain a force-fit mechanical bond. A

flange with four teeth shall be formed on each fin to

increase thermal contact and to space and lock the fins

uniformly in place. Both ends of each element pipe shall

be threaded with IPS standard threads.

* S-832 is 2" IPS steel pipe.

H-1 Element

Furnish and install H-1 baseboard heating

element as manufactured by Slant/Fin Corporation,

consisting of

⁄4" nominal copper tubing, with 3" x

⁄4"x .024"alumin

um fins, spaced 48 per linear foot. Fins

shall be mechanically bonded to the tubing to increase

ther

mal contact and to space and loc

k the fins unif

mly

in place. A flange with four teeth shall be formed on

each fin to increase thermal contact and to space and

lock the fins uniformly in place.

One end of each element tube shall be expanded

to receive the unexpanded end of another, without cou-

plings.

H-3 Element

Fur

nish and install H-3 baseboard heating

element as manufactured by Slant/Fin Corporation,

consisting of

⁄4" nominal copper tubing, with 3

⁄32" x

⁄2"x .011"aluminum fins bent to 2

⁄4"x 2

⁄2", spaced 55

per linear foot. Fins shall be mechanically bonded to the

tubing to increase thermal contact and to space and

lock the fins uniformly in place. A flange with four teeth

hall be formed on each fin to increase thermal contact

nd to space and lock the fins uniformly in place. One

nd of each element tube shall be expanded to receive

the unexpanded end of another, without couplings.

-4 Element

urnish and install H-4 baseboard heating element

as manufactured by Slant/Fin Corporation, consisting of

" nominal copper tubing, with 3

⁄3

x 2

⁄2"

x .011" alu-

inum fins bent to 3"x 2

⁄2"

, spaced 48 per linear foot.

ins shall be mechanically bonded to the tubing to

increase thermal contact and to space and lock the fins

niformly in place. A flange with four teeth shall be

ormed on each fin to increase thermal contact and to

pace and lock the fins uniformly in place. One end of

each element tube shall be expanded to receive the

nexpanded end of another, without couplings.

-5X Element

Furnish and install H-5 baseboard heating

element as manufactured by Slant/Fin Corporation,

onsisting of 1

⁄4"

nominal copper tubing, with 3" x

⁄4"

x .020" aluminum fins, spaced 48 per linear foot.

Fins shall be mechanically bonded to the tubing to

increase thermal contact and to space and lock the fins

niformly in place. A flange with four teeth shall be

ormed on each fin to increase thermal contact and to

space and lock the fins uniformly in place. One end of

each element tube shall be expanded to receive the

nexpanded end of another, without couplings.

H-6X Element

Furnish and install H-6 baseboard heating

element as manufactured by Slant/Fin Corporation,

onsisting of 1

⁄4"

IPS steel pipe (Schedule 40), with 3"

x 3

⁄4"x .028" steel fins, spaced 48 per linear foot. Fins

hall be mechanically bonded to the pipe to increase

hermal contact and to space and lock the fins uniformly

in place. A flange with four teeth shall be formed on

each fin to increase thermal contact and to space and

lock the fins uniformly in place. Both ends of each ele-

ment pipe shall be threaded with IPS standard threads.

E-75E Element

Furnish and install E-75 baseboard heating

element as manufactured by Slant/Fin Corporation,

consisting of

⁄4" nominal copper tubing with 2

⁄8" x

⁄8"x .009" aluminum fins, bent to 2

⁄1

"x 2

⁄8", spaced 55

per linear foot. A flange with four teeth shall be formed

on each fin to increase thermal contact and to space

and lock the fins uniformly in place. End fins are of plat-

ed steel for extra ruggedness. One end of each element

tube shall be expanded to receive the unexpanded end

of another, without couplings.

Rhino Cast Series

Furnish and install as shown on the plans Rhino

Cast series baseboard with required mounting compo-

nents and accessories as manufactured by Slant/Fin

Corporation.

Baseboard shall be 8

⁄16" high and 2

⁄16" deep

. End

sections shall have floor - standing legs cast into base-

board. Intermediate sections shall have adjustable floor

leveling bolts to compensate for uneven floors.

Optional w

all model shall mount on the wall without

floor standing legs below baseboard. Wall mounted cast

iron baseboard shall be 7

⁄16" high and 2

⁄16" deep

Baseboard shall be mounted ______ off of the floor.

Baseboard shall be made of durable cast iron with

metal push nipple used as water seal between sub-

assemblies. Screws securing baseboard to wall shall be

hidden and not visible from the frontal view.

Provide all required accessories for a complete

installation.

SLANT/FIN CORPORATION, Greenvale, N.Y. 11548 • Phone: (516) 484-2600

FAX: (516) 484-5921 • Canada: Slant/Fin LTD/LTEE, Mississauga, Ontario

www.slantfin.com