User's Manual

Mattress Assembly
Sleep Number®
Firmness Control™ system
(2 wired or 1 wireless)
contents
MATTRESS ASSEMBLY
▲
Position Mattress Cover
a) Place BOTTOM SECTION of mattress cover
(zipper side up) on top of the foundation or
bed platform.
b) Unzip the top portion and set it aside.
c) Holes in the bottom of the cover should
be at the head of the mattress and the
SLEEP NUMBER
®
bed label will be at the
foot of the mattress.
d) Place a Corner Lock
™
in each corner of
the mattress
cover.
Install Foam Border Walls
a) Place the two long FOAM BORDER WALLS
along the left and right sides of the
Mattress Cover.
The ends of the Foam Border Walls should
fit snugly inside the Corner Lock
™
.
b) Place the shorter Foam Border Walls
at the head and foot of the bed.
c) Make sure the border
walls are connected
securely and
squarely.
1
2
3
4
5
Inflate Air Chamber
(
s
)
a) Press any button on the remote to activate the hand control. (If using the
wireless remote with L and R buttons, press L or R to choose a side.) Press
the ∆ arrow several times to set the firmness to “20.” Inflation may take
about 10 minutes.
b) For dual chamber models, after the first chamber
is inflated, repeat for second chamber.
Then, insert the CENTER FOAM WALL
between the chambers, centering it
between the head and foot of the bed.
c) Zip on the top portion of the bottom
section and now the bottom
section is complete.
Install Air Chamber
(
s
)
a) Lay the AIR CHAMBER(s) in the mattress
cover so the Hose Connector(s) are on the
bottom and face the head of the bed.
b) Connectors will align with the small
openings at the base of the
mattress cover.
Install Foam Base Pad
a) Carefully shake out the pad prior
to placing in position.
b) Place the FOAM BASE PAD inside
the mattress cover with the clipped
ends at the head of the bed.
The pad should nestle inside the
Foam Border Walls.
Dual chamber model shown.
Install Foam Comfort Pads
a) Set the DUVET section onto the bottom section
with the zipper up.
b) Carefully shake out pads prior to placing in position.
c) Place the FOAM COMFORT PADS inside the
Duvet section (3˝ Intralux
™
Pad is positioned
with the textured side up).
Each sleeper can customize their side of the mattress
by choosing how to position the foam pads. Place
the 1˝ Memory foam pad on top for a more firm,
supportive surface. Place the 3˝ Intralux
™
foam
pad on top for a more plush surface.
6
7
Final Steps
a) Zip on the
duvet cover.
b) Move bed to
your desired
location.
You’re Done!
On the back you will find more information on
using the Firmness Control
™
system.
Q
A
Where are the Caps for Air Chamber(s)?
The caps are in the Firmness Control
™
system box.
Please store these in case you should ever want to
disassemble your bed and temporarily cap your
air chamber(s).
What if my Foam Comfort Pads appear
to be too small or irregular?
Gently shake the pads as you place them on your
mattress and they will recover to full size overnight.
What do I do if the motor doesn’t run?
Make sure the power cord is securely plugged into the
pump and the wall outlet. Check to see if the power
cord is plugged into an outlet which has power and
is not connected to an on/off wall switch.
Will my bed deflate if there is a power
surge or power loss?
No, your mattress will maintain its firmness. To protect
your Firmness Control
™
system, we do recommend using
a surge protector.
What if I notice a rubber smell from the
air chamber?
The odor you may smell is non-toxic and will fade
over time. To minimize the smell, allow the air
chamber to air out for a few hours and then lay
a couple of dryer sheets on top of the air chamber.
What if I feel like I’m rolling toward the
edge or toward the center of the mattress?
Although rare, these sensations could potentially be
experienced if one side of the mattress is set quite firm
and the other side quite soft. Call Customer Service for
a remedy to this situation if it is bothersome to you.
If you have any questions along the way, please look for the answer on our Web site: www.selectcomfort.com or call a Customer Service Representative at 1-800-472-7185.
If you are missing any
items, please e-mail
Customer Service at
customerservice@
selectcomfort.com or
call 1-800-472-7185.
Carefully check the contents of
your mattress boxes and compare
with the list below.
Mattress Cover
2 parts
• Top section (Duvet)
• Bottom section
Comfort
Control System
™
Remote
(
s
)
Varies by model.
All single chamber models include 1 remote only.
Wired remotes will be attached to the Firmness
Control
™™
system.
Foam Border Walls
2 long, 2 short
Air Chamber
(
s
)
2 for dual chamber models
1 for single chamber models
Center Foam Wall
Dual chamber models only
Foam Comfort Pads
1 of each for Twin size.
2 of each for Queen and King sizes.
• Memory Foam
• Intralux
™
Foam
Foam Base Pad
Caps for Air Chambers
2 Packages (Packaged inside the
Firmness Control
™
system box.)
Corner Lock
™
Package of 4
Bottom
Section
B
ottom
Section
B
ottom
Section
Top
S
ection
(Du
vet)
Top
S
ection
(Du
vet)
Top
S
ectio
n
(D
uvet)
Connect Firmness Control
™
system
a) Place the Firmness Control
™
system on the floor at the head of the bed.
Plug the power cord into the Firmness Control
™
system and then into an electrical
outlet. (You will hear several clicks indicating there is power.)
b) There are two hoses for each air chamber (one large and one small).
Pass the end of each hose through the small opening at the
base of the Mattress Cover and under the Foam Border
Wall to the corresponding chamber.
Connect the hose marked with “L” and the adjacent
smaller hose to the left chamber. Connect the other
two hoses to the right chamber.
c) Press hose connections together until they “click.”
Note:
When flipping the
reversible duvet,
stand at the side
of the bed and flip
from side to side.
You may need to
unzip the Duvet
section and
reposition the
foam topper pads
so your desired
pad is on top.
Insert2_JR 2/23/04 12:10 PM Page 2