Installation Guide

ManualsBrandsSloan ManualsToilet Flush Valves Repair Parts186-05 XL

Code No. 0816312

Rev. 1 (05/10)

INSTALLATION INSTRUCTIONS FOR EXPOSED REGAL

WATER CLOSET AND URINAL FLUSHOMETERS

LIMITED WARRANTY

Sloan Valve Company warrants its Regal XL Flushometers to be made of first class materials, free from defects of material or workmanship under normal use and

to perform the service for which they are intended in a thoroughly reliable and efficient manner when properly installed and serviced, for a period of three years (1

year for special finishes) from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or parts which prove to be

thus defective if returned to Sloan Valve Company, at customer’s cost, and this shall be the sole remedy available under this warranty. No claims will be allowed for

labor, transportation or other incidental costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company’s products directly from

Sloan Valve Company for purpose of resale.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY RESPONSIBLE FOR

ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.

Before you install the Regal XL Flushometer, be sure the items listed

below are installed. Also, refer to the rough-in diagrams on the next page.

• Closet or urinal fixture

• Drain line

• Water supply line

Important:

•

NSTALL ALL PLUMBING IN ACCORDANCE WITH APPLICABLE CODES

AND REGULATIONS.

•

WATER SUPPLY LINES MUST BE SIZED TO PROVIDE AN ADEQUATE

VOLUME OF WATER FOR EACH FIXTURE.

•

FLUSH ALL WATER LINES PRIOR TO MAKING CONNECTIONS.

The Sloan Regal XL Flushometer is designed to operate with 10 to 100

psi (69 to 689 kPa) of water pressure.

THE MINIMUM PRESSURE

REQUIRED TO THE VALVE IS DETERMINED BY THE TYPE OF FIXTURE

SELECTED.

Consult fixture manufacturer for minimum pressure

requirements. Most Low Consumption water closets (1.6 gpf/6.0 Lpf)

require a minimum flowing pressure of 25 psi (172 kPa).

Closet Flushometer

1½” (38 mm) Top Spud

MODELS 110/111,

113, 115 & 116

Closet Flushometer

1½” (38 mm) Back Spud

MODEL 120 & 122

Service Sink Flushometer

1½” (38 mm) Top Spud

MODEL 117

Urinal Flushometer

1¼” (32 mm) Top Spud

MODEL 180

Urinal Flushometer

¾” (19 mm) Top Spud

MODEL 186

Squat Toilet Flushometer

1½” (38 mm) Back Spud

MODEL 137

PRIOR TO INSTALLATION

TOOLS REQUIRED FOR INSTALLATION

• Straight blade screwdriver

• Sloan A-50 Super-Wrench™, Sloan A-109 Plier Wrench or smooth jawed spud wrench

Summary of content (6 pages)

PAGE 1
Code No. 0816312 Rev.
PAGE 2
VALVE ROUGH-INS MODELS 110/111 MODELS 113, 115 & 116 † † † † † † † † NOTE: Water Closet Valves with “-2.4” Model Designation deliver 2.4 gpf (9.0 Lpf) MODEL 117 MODELS 120/122 † † † MODEL 180 † MODEL 186 † † † † † NOTE: Model 180 requires 1” I.P.S.
PAGE 3
!!! IMPORTANT !!! !!! IMPORTANT !!! With the exception of Control Stop Inlet, DO NOT use pipe sealant or plumbing grease on any valve component or coupling! Never open Control Stop to where the flow from the valve exceeds the flow capability of the fixture. In the event of a valve failure, the fixture must be able to accommodate a continuous flow from the valve. !!! IMPORTANT !!! Protect the chrome or special finish of Sloan Flushometers — DO NOT USE toothed tools to install or service these valves.
PAGE 4
3 - INSTALL FLUSHOMETER AND HANDLE ASSEMBLY A Lubricate tailpiece O-ring with water. Insert Adjustable Tailpiece into Control Stop. Tighten Tailpiece Coupling by hand. B Align Flushometer directly above the Vacuum Breaker Flush Connection by sliding the Flushometer Body IN or OUT as needed. Tighten Vacuum Breaker Coupling by hand. D Install the red A-31 Handle Gasket on the Handle Assembly. Insert the ADA Handle Assembly (B-73-A) into the Handle opening in the Flushometer Body.
PAGE 5
CARE AND CLEANING DO NOT USE abrasive or chemical cleaners (including chlorine bleach) to clean Flushometers that may dull the luster and attack the chrome or special decorative finishes. Use ONLY mild soap and water, then wipe dry with clean cloth or towel. While cleaning the bathroom tile, protect the Flushometer from any splattering of cleaner. Acids and cleaning fluids will discolor or remove chrome plating. TROUBLESHOOTING GUIDE I. Flushometer does not function (no flush). 5.
PAGE 6
PARTS LIST 8 7 H-700 SE R 3A TO SS P IE 3B 1 2 Item Part No. No.