Installation Sheet

ManualsBrandsSloan ManualsPlumbingRoyal Collection 1.6 GPF Single-Flush Exposed Manual Specialty Water Closet Bedpan Washer Flushometer in Polished Chrome Color

Code No. 0816191

Rev. 2 (05/10)

INSTALLATION INSTRUCTIONS FOR SLIMLINE

BEDPAN WASHER WITH

EXPOSED ROYAL

AND REGAL

XL FLUSHOMETER

LIMITED WARRANTY

Sloan Valve Company warrants its Slimline Bedpan Washer to be made of first class materials, free from defects of material or workmanship under normal

use and to perform the service for which they are intended in a thoroughly reliable and efficient manner when properly installed and serviced, for a period

of three years (1 year for special finishes) from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or

parts which prove to be thus defective if returned to Sloan Valve Company, at customer’s cost, and this shall be the sole remedy available under this warranty.

No claims will be allowed for labor, transportation or other incidental costs. This warranty extends only to persons or organizations who purchase Sloan Valve

Company’s products directly from Sloan Valve Company for purpose of resale.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY RESPONSIBLE

FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.

Before you install the Sloan Bedpan Washer and Flushometer, be sure the items listed below are installed. Also, refer to the rough-in diagram below.

• Closet fixture

• Drain line

• Water supply line

Important:

•

ALL PLUMBING SHOULD BE INSTALLED IN ACCORDANCE WITH APPLICABLE CODES AND REGULATIONS.

•

WATER SUPPLY LINES MUST BE SIZED TO PROVIDE AN ADEQUATE VOLUME OF WATER FOR EACH FIXTURE.

•

FLUSH ALL WATER LINES PRIOR TO MAKING CONNECTIONS.

The Sloan Royal

and Regal

XL Flushometers are designed to operate with 10 to 100 psi (69 to 689 kPa) of water pressure.

THE MINIMUM PRESSURE

REQUIRED TO THE VALVE IS DETERMINED BY THE TYPE OF FIXTURE SELECTED.

Consult fixture manufacturer for minimum pressure requirements. Most

Low Consumption water closets (1.6 gpf/6.0 Lpf) require a minimum flowing pressure of 25 psi (172 kPa).

• Straight blade screwdriver

• Sloan A-50 Super-Wrench™, Sloan A-109 Plier Wrench or smooth jawed spud wrench

Slimline

Bedpan Washers

Royal BPW-1000 Standard

Royal BPW-1005 With Deoseptic Unit

Royal BPW-1010 With Retrofit Elbow

Royal BPW-1015 With Retrofit Elbow & Deoseptic Unit

Rrgal BPW-1000 XL Standard

Slimline

Bedpan Washers for ADA Installations

Royal BPW-1100 Standard

Royal BPW-1105 With Deoseptic Unit

Royal BPW-1110 With Retrofit Elbow

Royal BPW-1115 With Retrofit Elbow & Deoseptic Unit

Royal BPW-1150 With Grab Bar Offset

Royal BPW-1155 With Grab Bar Offset & Deoseptic Unit

Regal BPW-1100 XL Standard

Regal BPW-1150 XL With Grab Bar Offset

Slimline

Bedpan Washers — Diverter Assemblies

DV-100 Standard

DV-105 With Deoseptic Unit

DV-110 For ADA Installation

DV-115 For ADA Installation With Deoseptic Unit

DV-120 With Grab Bar Offset

DV-125 With Grab Bar Offset & Deoseptic Unit

DV-130 Replacement Model

DV-135 Replacement Model With Deoseptic Unit

PRIOR TO INSTALLATION

TOOLS REQUIRED FOR INSTALLATION

Summary of content (8 pages)

PAGE 1
Code No. 0816191 Rev.
PAGE 2
VALVE ROUGH-IN STANDARD INSTALLATION FLUSH VOLUME BPW 1000/1005 DV-100/105 BPW VALVE CAN BE PROVIDED WITH THE FOLLOWING FLUSHING VOLUMES: • Standard — Water Saver, 3.5 gpf (13.2 Lpf) • “-1.6” — Low Consumption, 1.6 gpf (6.0 Lpf) • “-2.4” — 2.4 gpf (9.0 Lpf) – European Standard CENTER LINE OF FIXTURE 4-3/4" (121 mm) 2-1/4" (57 mm) MIN. 1-1/2" (38 mm) 34-3/8" (873 mm) 1" I.P.S.
PAGE 3
!!! IMPORTANT !!! !!! IMPORTANT !!! With the exception of Control Stop Inlet, DO NOT use pipe sealant or plumbing grease on any valve component or coupling! This product contains mechanical and/or electrical components that are subject to normal wear. These components should be checked on a regular basis and replaced as needed to maintain the valve’s performance. !!! IMPORTANT !!! Protect the chrome or special finish of Sloan Flushometers — DO NOT USE toothed tools to install or service these valves.
PAGE 4
- INSTALL DIVERTER VALVE AND WALL SUPPORT FLANGE A Position diverter valve on top of tube gasket and secure with diverter valve coupling nut; tightening hand tight. X DIVERTER VALVE ASSEMBLY D Use the wall support flange as a template and mark off holes on finished wall for mounting screws. Remove diverter valve assembly and drill two 5/16” (8 mm) holes at the locations marked. Install an anchor in each hole.
PAGE 5
7 - INSTALL FLUSHOMETER A Lubricate tailpiece O-ring with water. Insert Adjustable Tailpiece into Control Stop. Tighten Tailpiece Coupling by hand. B Align Flushometer directly above the Vacuum Breaker Flush Connection by sliding the Flushometer Body IN or OUT as needed. Tighten Vacuum Breaker Coupling by hand.
PAGE 6
10 - ADJUST VOLUME OF SOLUTION DRAWN FROM DEOSEPTIC BOTTLE (9005 MODELS ONLY) A Using a screwdriver blade, pry off plug button on side of deoseptic swivel. Turn deoseptic adjustment screw as follows: DEOSEPTIC ADJUSTMENT SCREW Clockwise to DECREASE volume of solution drawn during flush Counterclockwise to INCREASE volume of solution drawn during flush B Replace plug button after making adjustment.
PAGE 7
TROUBLESHOOTING 5. PROBLEM: Water leaking back into Solution Bottle. See Royal, Naval, Dolphin, GEM, Sloan and Regal XL Flushometers Troubleshooting and Maintenance Guide for all problems regarding the flushometer valve and the flushing discharge. 1. PROBLEM: CAUSE: (a.) Rubber Ball damaged or missing. (b.) Rubber Ball not sitting in seat of Swivel & Ball Check Assembly. SOLUTION: (a.) Replace Rubber Ball using DV-1004-A Deoseptic Diverter Rebuild Kit (b.
PAGE 8
PARTS LIST 2 3A 3B TO SS P IE H-700 SE R 1 4 7 5 13 6 8 9B 9A 10 12 11 Item Part No. No.