Installation Guide

ManualsBrandsSloan ManualsToilet Flush Valves Repair Parts3250401

Code No. 0816452

Rev. 0a (05/03)

INSTALLATION INSTRUCTIONS

FOR RETROFIT AND COMPLETE

VALVE INSTALLATION

8100 Series Complete Flushometer Models

RESS Series Retrofit Conversion Kit Models

Made in the U.S.A.

LIMITED WARRANTY

Sloan Valve Company warrants its G2 Optima Plus Flushometers to be made of first class materials, free from defects of material or workmanship under

normal use and to perform the service for which they are intended in a thoroughly reliable and efficient manner when properly installed and serviced, for

a period of five years (1 year for special finishes) from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace any

part or parts which prove to be thus defective if returned to Sloan Valve Company, at customer’s cost, and this shall be the sole remedy available under

this warranty. No claims will be allowed for labor, transportation or other incidental costs. This warranty extends only to persons or organizations who

purchase Sloan Valve Company’s products directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of the batteries.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY

RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.

The Sloan G2 Optima Plus Flushometer provides the ultimate in sanitary

protection and automatic operation. The Optima Plus uses advanced infrared

technology to detect a user's presence and initiate a flushing cycle once the

user steps away. The Optima Plus is powered by four AA batteries which will

provide up to three years of service (based on 4000 flushes per month).

RESS Optima Plus models are used to convert existing Royal and Regal style

flushometers to sensor operation.

8100 series Optima Plus valves are complete flushometer valves and ideal

for new installations.

When installing any Optima Plus valve it is important that the flush model

matches the requirements of the plumbing fixture.

Optima Plus Water Closet Models can be furnished for the following:

1.6 gpf/6.0 Lpf For Low Consumption Bowls

2.4 gpf/9.0 Lpf For 9 Liter European Water Closets

3.5 gpf/13.2 Lpf For older Water Closets

Optima Plus Urinal Models can be furnished for the following:

0.5 gpf/1.9 Lpf For Wash Down Urinals

1.0 gpf/3.8 Lpf For Low Consumption Urinals

1.5 gpf/5.7 Lpf For older Siphon Jet Urinals

3.5 gpf/13.2 Lpf For older Blow Out Urinals

Summary of content (7 pages)

PAGE 1
Code No. 0816452 Rev. 0a (05/03) INSTALLATION INSTRUCTIONS FOR RETROFIT AND COMPLETE VALVE INSTALLATION RESS Series Retrofit Conversion Kit Models 8100 Series Complete Flushometer Models Made in the U.S.A. The Sloan G2 Optima Plus Flushometer provides the ultimate in sanitary protection and automatic operation. The Optima Plus uses advanced infrared technology to detect a user's presence and initiate a flushing cycle once the user steps away.
PAGE 2
VALVE ROUGH-IN — Figure 1 Typical Water Closet Installation Typical Urinal Installation Model 8110/8111 Models 8180 & 8186 Reference for RESS-C Retrofit Reference for RESS-U Retrofit 2¼” (57 mm) MIN. 11½” (292 mm) FINISHED WALL 16½” (419 mm) 2¼” (57 mm) MIN. 1” I.P.S. (25 mm DN) SUPPLY 4¾” (121 mm) C/L OF FIXTURE 11½” (292 mm) 16½” (419 mm) C/L OF FIXTURE 8180 1” I.P.S. (25 mm DN) SUPPLY 8186 ¾” I.P.S.
PAGE 3
INSTALLATION Step 3 — Install Vacuum Breaker Flush Connection (Figure 5) For Complete Valve Installation, Start Here. For RESS Retrofit Installations, Start at Step 5. Slide the Spud Coupling, Nylon Slip Gasket, Rubber Gasket and Spud Flange over the Vacuum Breaker Tube. Insert Vacuum Breaker Tube into fixture spud. Hand tighten Spud Coupling onto fixture spud. If cutting Vacuum Breaker Tube to size, note that Critical Line (C/L) on Vacuum Breaker must typically be 6” (152 mm) above fixture.
PAGE 4
When Retrofitting an Existing Valve, Start Here Step 7 — Assemble Flex Tube Diaphragm to Optima Plus Assembly (Figure 9) Remove Tab at underside of Optima Plus Assembly. Insert metal end of Flex Tube into the hole at underside of Optima Plus Assembly. The O-ring must be fully inserted into the hole. Push the Diaphragm securely against underside of Optima Plus Assembly. Place entire Assembly onto the Valve Body. Note: Sensor Lens must face directly forward.
PAGE 5
OPERATION Step 9 — Test Sensor Operation (Figure 12) Stand in front of the Optima Plus sensor, wait ten (10) seconds, then step away. Solenoid will “click,” indicating that the Optima Plus is operating. STAND IN FRONT OF SENSOR FOR TEN (10) SECONDS Figure 12 click 1. A continuous, INVISIBLE light beam is emitted from the Optima Plus Sensor. 2.
PAGE 6
TROUBLESHOOTING GUIDE For information and instructions on field converting G2 Optima Plus Module settings or to activate the Stadium Flush™ Feature in urinal models, refer to the Sloan G2 Optima Plus Conversion Guide (0816453). This manual and the Optima Plus Repair and Maintenance Guide are available at www.sloanvalve.com. I. Sensor Flashes Continuously Only When User Steps Within Range. A. Unit in Start-Up mode; no problem. This feature is active for the first ten (10) minutes of operation. II.
PAGE 7
PARTS LIST Item Part Number No.