Installation Guide

ManualsBrandsSloan ManualsToilet Flush Valves Repair Parts3250401

Step 9 — Test Sensor Operation (Figure 12)

Stand in front of the Optima Plus sensor, wait ten (10) seconds, then step

away. Solenoid will “click,” indicating that the Optima Plus is operating.

RANGE ADJUSTMENT

The Optima Plus has a factory set sensing range:

Water Closet Models — 22" to 42" (559 mm to 1067 mm)

Urinal Models — 15" to 30" (381 mm to 762 mm)

The Factory setting should be satisfactory for most installations. If a

range adjustment is required, refer to the Range Adjustment

instructions on this page.

Step 10 — Adjust Control Stop to Suit Fixture (Figure 13)

Adjust Control Stop to meet the flow rate required for proper cleansing of the

fixture. If installed, remove Vandal Resistant Control Stop Cap. Open Control

Stop COUNTERCLOCKWISE ½ turn from the closed position. Activate

Flushometer by placing hand in front of Optima Plus Sensor Lens for ten (10)

seconds (or press override button) and then moving it away. Adjust Control

Stop after each flush until the rate of flow delivered properly cleanses the

fixture.

IImmppoorrttaanntt::

A Sloan Flushometer is engineered for quiet operation. Excessive

water flow creates noise, while too little water flow may not satisfy the needs

of the fixture. Proper adjustment is made when:

1. The plumbing fixture is cleansed after each flush without splashing water

out from the lip.

2. A quiet flushing cycle is achieved.

The Control Stop should never be opened to the point where the flow

from the valve exceeds the flow capability of the fixture. In the event

of a valve failure, the fixture must be able to accommodate a

continuous flow from the valve.

Step 11 — Install Stop Cap

For RESS retrofit applications, reuse Stop Cap from existing valve. In

complete valve installations, a new Stop Cap is provided.

For G2 models, follow the instructions packaged with the Free Spinning

Vandal Resistant Stop Cap.

OPERATION

1. A continuous, INVISIBLE light

beam is emitted from the Optima

Plus Sensor.

2. As the user enters the beam's

effective range, 22 to 42 inches

(559 mm to 1067 mm) for

closet installations and 15 to 30

inches (381 mm to 762 mm) for

urinal installations, the beam is

reflected into the Scanner

Window to activate the Output

Circuit. Once activated, the

Output Circuit continues in a

"hold" mode for as long as the

user remains within the effective

range of the sensor.

3. When the user steps away, the

loss of reflected light initiates an

electrical "one-time" signal that

activates the flushing cycle to

flush the fixture. The Circuit

automatically resets and is ready

for the next user.

RANGE ADJUSTMENT (Adjust only If Necessary)

The G2 Optima Plus has a factory set sensing range:

Water Closet Models — 22" to 42" (559 mm to 1067 mm)

Urinal Models — 15" to 30" (381 mm to 762 mm)

The Factory setting should be

satisfactory for most instal-

lations.

If the range is too short (i.e., not

picking up users) or too long

(i.e., picking up opposite wall or

stall door) the range can be

adjusted.

NNoottee::

Water does not have to be

turned off to adjust range.

Loosen the two Screws on top of

the unit. Remove the Override

Button. Remove the Rubber Plug

from top of Electronic Sensor

Module to uncover the

Potentiometer.

RANGE ADJUSTMENT PROCEDURE

For the first ten (10) minutes of operation, a Visible Red Light flashes in the

Sensing Window of the G2 Optima Plus Flushometer when a user is

detected. This Visible Red Light feature can be reactivated after ten (10)

minutes by opening and closing the Battery Compartment Door.

Check the range by stepping toward the unit until the Red Light flashes,

indicating the Sensor's maximum detection limit. Adjust the Range

Potentiometer Screw located on top of the Sensor Module a few degrees

CLOCKWISE to increase the range or a few degrees COUNTERCLOCKWISE

to decrease the range. Repeat this adjustment until the desired range is

achieved.

Always Determine the Sensing Range with Metal Cover and Lens

Window On Top of the Unit.

IImmppoorrttaanntt::

Adjust in small increments only! Range Potentiometer Adjustment

Screw rotates only ¾ of a turn;

DDOO NNOOTT

over-rotate.

When range adjustment is satisfactory, replace the Rubber Plug. Reinstall

Override Button and tighten the two Screws on top of the unit.

STAND IN FRONT

OF SENSOR FOR

TEN (10) SECONDS

STEP AWAY FROM

SENSOR AND LISTEN

FOR “CLICK”

TEST SENSOR WITH COVER IN PLACE

click

Figure 12

Figure 13

COUNTER-

CLOCKWISE

Decreases

Range

Increases

Range

Figure 14