Installation Guide

ManualsBrandsSloan ManualsBathroom Sink FaucetsOptima Polished Chrome Touchless Single Hole Bathroom Sink Faucet

Code No. 0816302

Rev. 3b (11/08)

INSTALLATION INSTRUCTIONS FOR

SENSOR ACTIVATED LAVATORY FAUCETS

LIMITED WARRANTY

Sloan Valve Company warrants its EBF-85 and EBF-187 Faucets to be made of first class materials, free from defects of material or workmanship under normal use and to perform the

service for which they are intended in a thoroughly reliable and efficient manner when properly installed and serviced, for a period of three years (1 year for special finishes) from date of

purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or parts which prove to be thus defective if returned to Sloan Valve Company, at customer's

cost, and this shall be the sole remedy available under this warranty. No claims will be allowed for labor, transportation or other incidental costs. This warranty extends only to persons or

organizations who purchase Sloan Valve Company's products directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of the batteries (battery operated

models).

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES

OF ANY MEASURE WHATSOEVER.

PRIOR TO INSTALLATION

Prior to installing the Sloan EBF-85 or EBF-187 Faucet, install the items

listed below. Also, refer to the Rough-In illustrations on Page 2.

• Lavatory/sink

• Drain line

• Hot and cold water supply lines or tempered water supply line

Mixing Valve

When installing the faucet with a Sloan mixing valve, these Installation

Instructions AND the Installation Instructions packaged with the mixing

valve MUST be followed.

Important:

• INSTALL ALL PLUMBING IN ACCORDANCE WITH APPLICABLE CODES

AND REGULATIONS.

• KEEP THREAD SEALANT OUT OF YOUR WATERWAY TO PREVENT

COMPONENT PART DAMAGE! DO NOT USE ANY SEALANT ON

COMPRESSION FITTINGS. FOR THREADED PIPE FITTINGS, DO NOT

APPLY SEALANT TO THE FIRST TWO “STARTER” THREADS.

• FLUSH ALL WATER LINES UNTIL WATER IS CLEAR BEFORE CONNECTING

SOLENOID TO SUPPLY STOPS.

DO NOT INSTALL THE BATTERIES UNTIL THE FAUCET IS COMPLETELY

INSTALLED. If the batteries are installed before the fiber optic cable has

been connected to the valve module, the faucet will not properly set the

sensing range for the sink on which it is installed.

DO NOT INSTALL THE SPRAY HEAD UNTIL AFTER THE SUPPLY LINES

HAVE BEEN FLUSHED.

BAK-CHEK

TEE USAGE

When connecting the Sloan EBF-85 or EBF-187 Faucet to both hot and cold

water supplies, a Bak-Chek

Tee is provided and required as illustrated in

the Rough-in illustrations on Page 2. Water temperature can be controlled

by adjusting the supply stops.

When connecting the faucet to a single line water supply or a pre-tempered

water supply, a Bak-Chek

Tee is not required.

A Bak-Chek

Tee is not required or provided when a Temperature Mixing

Valve is included with the faucet.

TOOLS REQUIRED FOR INSTALLATION

• Open end wrenches for hex sizes: 1/2”, 9/16”, 5/8”, 15/16”

• Basin wrench

• Phillips head screwdriver, #2

• Hammer (if installing plastic or hollow wall anchors to mount valve

module)

• 0.05” hex wrench (supplied)

• Spray head key (supplied)

• 1/4” drill bit (if plastic wall anchors are used to mount valve module)

• 5/16” drill bit (if hollow wall anchors are used to mount valve module)

• 3/8” drill bit (if toggle nut anchors are used to mount valve module)

Model EBF-85

Battery Powered, Sensor Activated Lavatory Faucet

Furnished with a Black Plastic Throat Plate

Model EBF-187

Battery Powered, Sensor Activated Lavatory Faucet

Furnished with a Chrome Plated Metal Throat Plate

Compliant to: ASME A112.18.1

and CSA B125.1

Summary of content (8 pages)

PAGE 1
Code No. 0816302 Rev. 3b (11/08) INSTALLATION INSTRUCTIONS FOR SENSOR ACTIVATED LAVATORY FAUCETS Model EBF-187 Model EBF-85 Battery Powered, Sensor Activated Lavatory Faucet Battery Powered, Sensor Activated Lavatory Faucet Furnished with a Chrome Plated Metal Throat Plate Furnished with a Black Plastic Throat Plate Compliant to: ASME A112.18.1 and CSA B125.
PAGE 2
FAUCET ROUGH-IN EBF-85 and EBF-187 Faucet with Bak-Chek® Tee for Hot and Cold Water Supply (shown with 4” trim plate) EBF-85 and EBF-187 Faucet with ADM Variation Mixing Valve for Hot and Cold Water Supply (shown with 8” trim plate) EBF-85 and EBF-187 Faucet with BDM and BDT Variation Mixing Valves for Hot and Cold Water Supply (shown with 4” trim plate) FAUCET INSTALLATION EBF-85 and EBF-187 Battery Powered Faucet Install Faucet Spout and Trim Plate — Refer to the appropriate step (1A-1C) for your app
PAGE 3
1B A ETF-312-A (for EBF-187) Single Hole 4” Trim Plate 1C Slide Rubber Faucet Gasket onto Faucet Shank. Ensure that Roll Pin on base of Faucet fits into hole in Rubber Faucet Gasket. ETF-510-A (for EBF-85/187) Single Hole 8” Trim Plate A Slide Rubber Faucet Gasket onto Faucet Shank. Ensure that Roll Pin on base of Faucet fits into hole in Rubber Faucet Gasket. B Slide Trim Plate and Back-up Spacer onto Faucet Shank. Align Roll Pin with small slot in Trim Plate.
PAGE 4
Install Valve Module 4 Connect Flex Hose or Copper Tubing to Solenoid Valve and Connect Fiber Optic Cable 5 A Install Valve Module into Wall Bracket Base as shown below. B Insert tab of Wall Bracket into slot of Wall Bracket Base. C Swing Wall Bracket into position as shown below and secure using the Self-tapping Screw provided. A Connect the free end of the Flex Hose or Copper Tube (now attached to the Spout) to the outlet side of the Solenoid Valve as shown below.
PAGE 5
Start Up Mode 8 Start-Up ® Sloan OPTIMA Plus EBF-85 and EBF-187 Electronic, Sensor Activated Lavatory faucets use Adaptive Sensing technology to automatically set its sensing range once power is supplied to the faucet. No mechanical range adjustments are required. The faucet automatically adapts its range to its surrounding environment. A Remove Spray Head. B Open supply stop(s), then activate Faucet for 30 seconds by placing hands in front of sensor.
PAGE 6
BATTERY REPLACEMENT PROCEDURE (Step 7A on Page 4) SOLENOID SCREEN FILTER CLEANING PROCEDURE Note: Before cleaning the Screen Filter, turn off the water supply at the supply stop(s) and activate the faucet to relieve any pressure in the system. ® Sloan OPTIMA Plus EBF-85 and EBF-187 Battery Powered, Sensor Activated Lavatory faucet models are furnished with four (4) Duracell Csize Alkaline batteries that provide up to 2 years of operation (at 8000 cycles per month).
PAGE 7
TROUBLESHOOTING GUIDE INDICATOR: Module produces audible “BEEPs” when a target is placed in the detection zone of the Sensor and Solenoid Valve produces an audible “CLICK,” but NO water flows. CAUSE: Water supply to faucet is not open. SOLUTION: Open supply stop(s) completely. CAUSE: Bak-Chek® is installed backward. SOLUTION: Reinstall Bak-Chek® properly. CAUSE: Solenoid Filter is clogged. SOLUTION: Remove, clean, and reinsert. Replace with EBF-1004-A Solenoid Filter Kit if necessary.
PAGE 8
PARTS LIST 1 10 2 3 12 11 4 13 5 16 8 6 14 7 15 8 9 Item Part No. No. Description Item Part No. No. Description 1 Faucet and Sensor Assembly (EBF-85 with Black Plastic Throat Plate) Faucet and Sensor Assembly (EBF-187 with CP Metal Throat Plate) Fiber Optic Sensor Cable Assembly Only (replaces EBF-12-A, includes lens holder) 0.5 gpm (1.9 Lpm) Spray Head with Key (female thread) 2.2 gpm (8.3 Lpm) Aerator Spray Head with Key (female thread) 2.2 gpm (8.