Installation Guide

ManualsBrandsSloan ManualsBathroom Sink FaucetsOptima Polished Chrome Touchless 4-in Centerset Bathroom Sink Faucet

Code No. 0816321

Rev. 2b (09/08)

INSTALLATION INSTRUCTIONS

FOR BATTERY POWERED

SENSOR ACTIVATED LAVATORY FAUCETS

LIMITED WARRANTY

Sloan Valve Company warrants its EBF-615 and EBF-650 Faucets to be made of first class materials, free from defects of material or workmanship under normal

use and to perform the service for which they are intended in a thoroughly reliable and efficient manner when properly installed and serviced, for a period of three

years (1 year for special finishes) from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or parts which

prove to be thus defective if returned to Sloan Valve Company, at customer’s cost, and this shall be the sole remedy available under this warranty. No claims will

be allowed for labor, transportation or other incidental costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company’s

products directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of the batteries.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY

RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.

Compliant to:

ASME A112.18.1 and

CSA B125.1

PRIOR TO INSTALLATION

Prior to installing the Sloan EBF-615 or EBF-650 faucet, install the items

listed below. Also, refer to rough-in illustrations on Page 2.

• Lavatory/sink

• Drain line

• Hot and cold water supply lines or tempered water supply line

Mixing Valve

When installing the faucet with a Sloan Mixing Valve, these Installation

Instructions AND the Installation Instructions packaged with the Mixing

Valve MUST be followed.

Important:

• ALL PLUMBING IS TO BE INSTALLED IN ACCORDANCE WITH

APPLICABLE CODES AND REGULATIONS.

• KEEP THREAD SEALANT OUT OF YOUR WATERWAY TO PREVENT

COMPONENT PART DAMAGE! DO NOT USE ANY SEALANT ON

COMPRESSION FITTINGS. FOR THREADED PIPE FITTINGS, DO NOT

APPLY SEALANT TO THE FIRST TWO “STARTER” THREADS.

• FLUSH ALL WATER LINES UNTIL WATER IS CLEAR BEFORE

CONNECTING SOLENOID TO SUPPLY STOPS.

DO NOT INSTALL THE BATTERIES UNTIL THE FAUCET IS COMPLETELY

INSTALLED. If batteries are installed before sensor cable is connected to

control module, the faucet will not properly set the sensing range for the

sink on which it is installed.

TOOLS REQUIRED FOR INSTALLATION

• Open end wrenches for the following hex sizes: 1/2”, 9/16”, 5/8”,

11/16”, 1”

• Basin wrench

• Phillips head screwdriver, #2

• Hammer (if installing plastic or hollow wall anchors to mount control

module)

• Pliers

• 1/4" drill bit (if installing plastic wall anchors to mount control module)

• 5/16" drill bit (if installing hollow wall anchors to mount control module)

• 3/8" drill bit (if installing toggle nut anchors to mount control module)

Bak-Chek

Tee Usage

When connecting the EBF-615 or EBF-650 faucet to both hot and cold

water supplies, a Bak-Chek

Tee is provided and required as illustrated in

Step 3. Water temperature can be controlled by adjusting the supply stops.

When connecting the faucet to a single line water supply or a pre-tempered

water supply, a Bak-Chek

Tee is not required.

A Bak-Chek

Tee is not required or provided when a Temperature Mixing

Valve is included with the faucet.

EBF-615

Pedestal,

Battery Powered,

Sensor Activated

Lavatory Faucet

EBF-650

4” Centerset,

Battery Powered,

Sensor Activated

Lavatory Faucet

Summary of content (8 pages)

PAGE 1
Code No. 0816321 Rev. 2b (09/08) INSTALLATION INSTRUCTIONS FOR BATTERY POWERED SENSOR ACTIVATED LAVATORY FAUCETS EBF-615 Pedestal, Battery Powered, Sensor Activated Lavatory Faucet EBF-650 4” Centerset, Battery Powered, Sensor Activated Lavatory Faucet Compliant to: ASME A112.18.1 and CSA B125.1 PRIOR TO INSTALLATION Prior to installing the Sloan EBF-615 or EBF-650 faucet, install the items listed below. Also, refer to rough-in illustrations on Page 2.
PAGE 2
FAUCET ROUGH-IN EBF-615 Faucet with Bak-Chek® Tee for Hot and Cold Water Supply (shown with 4” trim plate) EBF-615 Faucet with ADM Variation Mixing Valve for Hot and Cold Water Supply (shown with 8” trim Plate) EBF-615 Faucet with BDM and BDT Variation Mixing Valves for Hot and Cold Water Supply (shown with 4” trim Plate) EBF-650 Faucet with BDM and BDT Variation Mixing Valves for Hot and Cold Water Supply EBF-650 Faucet with Bak-Chek® Tee for Hot and Cold Water Supply FAUCET SIDE VIEW EBF-615 EBF-650
PAGE 3
1A Install Faucet Spout and Optional Trim Plate — EBF-615 1B Sloan Valve Company recommends installation of our trim plate with antirotation feature to prevent rotation of this single-hole pedestal-style faucet. A Install Faucet Spout — EBF-650 Refer to the Installation Instructions included with the ETF-578-A Trim Plate for additional information about using an 8" Trim Plate with an EBF-650 faucet. A Install Faucet Spout as shown. Use plumber’s putty to secure optional Trim Plate, if used.
PAGE 4
Mount Control Module to Wall 5 Control Module Connection A Install the Control Module in an appropriate location. Control Module must be installed so that all cables enter from the bottom of the unit. When installed, Cables from the Spout and Solenoid Valve to the Control Module should have some slack. A Route Cables from Solenoid Valve and Spout to the Control Module. B Insert Locking Connector from Solenoid Valve into mating Receptacle.
PAGE 5
Start-Up 8 A B 9 The OPTIMA Plus EBF-615 and EBF-650 Faucets are factory set to operate when hands are placed 4 to 5 inches (102 to 127 mm) from Sensor. This range should be satisfactory for most installations. If range adjustment is required, refer to the following range adjustment procedure. Activate ( "dry fire") Faucet by placing hands in front of the Sensor. The Solenoid Valve should “click.” Once hands are removed the Solenoid Valve should click again.
PAGE 6
11 A Install Cover onto Control Module Operation Install Cover over the Control Module making sure that all four (4) locking tabs snap into place. Secure using the two (2) screws provided. Cover can be installed in only one orientation. 1. A continuous invisible beam of infrared light is emitted from the sensor located on the throat of the lavatory faucet. 2.
PAGE 7
Solenoid Screen Filter Cleaning Procedure A Turn off water supply at supply stop(s). Activate Faucet to relieve system pressure. B Remove Water Supply Line from Inlet Side of Solenoid Valve. Remove Cap, Water Line Fitting, Gasket, Filter Housing and Filter from Solenoid Valve Housing. C Slide Filter off Filter Housing. Clean Filter using fresh tap water only. If necessary, use a small brush to clean. Use caution while cleaning to prevent damage to Filter.
PAGE 8
EBF-650 PARTS LIST EBF-615 8 1A 3 3 2 1B 2 7 6 9 4A 4B 10 5 14 H LD C T CO OT OO LD H 12 11A 11B 13 Item Part No. No. Description Item Part No. No. Description 1A 1B — 2 CP Faucet Assembly 4” Centerset (ETF-650) Pedestal Faucet Spout and Sensor Assembly (EBF-615) Sensor Only 0.5 gpm (1.9 Lpm) Spray Head with Key (male thread) 2.2 gpm (8.3 Lpm) Aerator Spray Head with Key (male thread) CP Spray Head 0.